CONNOR-WINFIELD EGOV5S3M

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
14 PIN DIP 5.0V HCMOS STRATUM 3 OCVCXO
with OVEN READY MONITOR
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
TABLE 1.0
UNITS
MINIMUM
-40
NOMINAL
-
MAXIMUM
85
UNITS
°C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATIONS
PARAMETER
Center Frequency
Frequency Stability
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
(Vcc)
MINIMUM
40
-0.25
-4.6
0
NOMINAL
-
MAXIMUM
80
0.25
4.6
70
UNITS
MHz
ppm
ppm
°C
Vdc
4.75
5.00
5.25
Power Consumption (Vcc = 5.0V)
-
-
2.0
W
Phase Jitter (BW =12KHz to 20MHz)
-
-
1
pS RMS
Phase Jitter (BW =10Hz to 20MHz)
-
-
3
pS RMS
Period Jitter
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 10KHz offset
Start Up Time: Oscillator
Warm Up Time
TDEV @ 1.0 Sec.
TDEV @ 4.0 Sec.
-
-75
-130
-
3
10
1
1
2
pS RMS
dBc/Hz
dBc/Hz
mS
Minute
nS
nS
INPUT CHARACTERISTICS
Control Voltage Range
(Pin 1)
MINIMUM
NOMINAL
MAXIMUM
UNITS
0.5
2.5
4.5
Vdc
+/-18
-
+/-30
ppm
9
-
-
ppm/V
(Vc)
Frequency Pullability
Slope of Frequency Adjust
Input Impedance
NOTE
1
2
100k
-
-
Ohm
(Pin 3)
(Vih)
2.0
-
-
Vdc
Disable Voltage
(Pin 3)
(Vil)
-
-
0.8
Vdc
FEATURES
MINIMUM
4.0
-
NOMINAL
-
MAXIMUM
15
0.4
UNITS
pf
Vdc
Vdc
-4
45
50
4
55
mA
mA
%
-
-
6
nS
Pin 12
-
-
0.4
Vdc
Pin 12
3.0
-
-
Vdc
(Voh)
(Vol)
Current
(High)
(Low)
Duty Cycle measured at 1.5V
FREQUENCY ADJUST
TRI-STATE ENABLE / DISABLE
FUNCTION
LOW JITTER <1pS RMS
FREQUENCY TOLERANCE: ±4.6ppm
NOTE
TEMPERATURE RANGE: 0 to 70°C
OVEN READY MONITOR
HERMETICALLY SEALED PACKAGE
RoHS COMPLIANT / LEAD FREE
ORDERING INFORMATION
TABLE 5.0
PACKAGE CHARACTERISTICS
5.0V OPERATION
FREQUENCY STABILITY: ±0.25ppm
TABLE 4.0
(Ioh)
(Ioh)
Rise / Fall Time 10% to 90%
Oven Ready Monitor voltage when oven is
cold, not at operating temperature.
Oven Ready Monitor voltage when oven is
warm, at operating temperature.
NOTE
5
HCMOS OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage
(High)
(Low)
The Connor-Winfield
EGOV5S3M is a hermetically
sealed 14 Pin DIP 5.0V Oven
Controlled, Voltage Controlled
Crystal Oscillator (OCVCXO)
with a Tri-State HCMOS
output. The EGOV5S3M
features an Oven Ready
Monitor and is designed for
Stratum 3 applications
requiring low jitter and tight
frequency stability.
3
4
Enable Voltage
Package
Soldering Process
DESCRIPTION
TABLE 3.0
PARAMETER
EGOV5S3M
NOTE
TABLE 2.0
(Fo)
CW
0803
EGOV5S3M
80.0MHZ
14 pin DIP, hermetically sealed, grounded case, welded package
RoHS compliant, lead free. See solder profile on page 2.
EGOV5S3M
OCXO
SERIES
- 080.0M
CENTER
FREQUENCY
Specifications subject to change without notice.
DATA SHEET #:
Cx061
PAGE 1
OF
2
REV: 01
DATE:
01/16/08
aCopyright 2008 Connor-Winfield all rights reserved.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
Notes:
1) Frequency vs. temperature stability, Vc = 2.50V.
2) Inclusive of calibration, operating temperature range, supply voltage change, load
change, shock and vibration, 10 years aging, Vc = 2.50V.
3) After one minute of operation at 25C, the unit will be within +/-0.5ppm of its final
stabilized frequency. The final stabilized frequency is that which is measured after 30
minutes of continuous operation at a stable 25C ambient temperature.
4) Referenced to Fo @ 25°C, Positive Transfer Characteristic
5) Oscillator output is enabled with no connection on pin 3.
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20
seconds.
SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C
±5°C for 20 Seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.
Pin Connections
Package Outline
TABLE 6.0
.430 MAX
Pin
1
3
7
8
12
14
(10.922mm)
.200
(5.08mm)
Dimensional Tolerance:
±.005 (.127mm)
Test Circuit
Connection
Control Voltage
Enable / Disable
Ground (Case)
Output
Oven Monitor
Vcc
Solder Profile
Temperature
260°C
260°C
220°C
OVEN
MONITOR
REF.
SUPPLY
4.5Vdc
14
5.0Vdc
12
180°C
150°C
8
120°C
WW
1
20K
POT
3
7
ENABLE/
CONTROL DISABLE
VOLTAGE
0
120 S
Max.
Time
10 S
60 S
Max.
360 Sec. Max.
Specifications subject to change without notice.
DATA SHEET #:
Cx061
PAGE 2
OF
2
REV:
01
DATE:
01/16/08
aCopyright 2008 Connor-Winfield all rights reserved.