THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. www.conwin.com PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ABSOLUTE MAXIMUM RATINGS TABLE 1.0 PARAMETER Storage Temperature Supply Voltage Control Voltage UNITS MINIMUM NOMINAL MAXIMUM UNITS (Vcc) (Vc) -40 -0.5 -0.5 - 85 4.5 4.5 °C Vdc Vdc NOMINAL MAXIMUM UNITS (Fo) MINIMUM 1.544 - 20.0 1.5 MHz ppm 1 2 3 OPERATING SPECIFICATIONS NOTE TABLE 2.0 PARAMETER Center Frequency Frequency Calibration, Vc=1.59 Vdc -1.5 Frequency Stability Aging (Daily) Aging (20 Years) Total Frequency Tolerance Operating Temperature Range -0.25 -30 -2.5 -4.6 0 - 0.25 30 2.5 4.6 70 ppm ppb ppm ppm °C Vdc Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 450 mA Phase Jitter (BW=12KHz to 20MHz) - - 1 ps rms Phase Jitter (BW=10Hz to 20MHz) - - 3 ps rms Period Jitter SSB Phase Noise at 10Hz offset SSB Phase Noise at 10KHz offset Warm Up Time TDEV @ 1.0 Sec. TDEV @ 4.0 Sec. - -90 -135 - 5 5 1 2 ps rms dBc/Hz dBc/Hz Minutes nS nS MINIMUM NOMINAL MAXIMUM UNITS INTPUT CHARACTERISTICS Control Voltage Range (Vc) 4 0.3 1.59 3.0 Vdc - -25 ppm 6 Frequency at Vc=3.0 Vdc 25 - 38 ppm 6 Slope of Frequency Adjust 18.5 - - ppm/V Input Impedance 100k - - Ohm MINIMUM NOMINAL MAXIMUM UNITS 2.6 -4 45 - - 15 0.4 4 55 6 pf Vdc Vdc mA mA % nS LOAD Voltage (High) (Low) Current (High) (Low) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% PACKAGE CHARACTERISTICS Package 50 - FREQUENCY ADJUST 3.3V OPERATION NOTE TEMPERATURE STABILITY ±0.25ppm FREQUENCY TOLERANCE OF ±4.6ppm OVER TEN YEARS SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING TABLE 5.0 Surface Mount, Non-hermetic package consisting of a n FR4 substrate with grounded metal cover. PROCESS RECOMMENDATIONS Solder Reflow TABLE 6.0 The component solder used internal to this device has a m elting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Ultrasonic cleaning is not recommended ORDERING INFORMATION BSOV3S3 - 12.80MHz Notes: 1) 2) 3) 4) Initial calibration @ 25°C, Vc=1.59 Vdc. Frequency vs. temperature stability At the time of shipment after48 hours of operation. Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 20 years aging. 5) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of contin uous operation at a stable 25°C 6) Referenced to Fo @ 25°C, Positive Transfer Characteristic DATA SHEET #: FEATURES LOW JITTER <1pS RMS TABLE 4.0 (Voh) (Vol) (Ioh) (Ioh) The Connor-Winfield BSOV3S3 is a true Surface Mount 3.3V, Voltage Controlled Oven Controlled Crystal Oscillator (VCOCXO) with an HCMOS output. The BSOV3S3 is designed for Stratum 3 applications requiring high pullability, tight frequency stability and low jitter. NOTE -38 PARAMETER DESCRIPTION 5 Frequency at Vc=0.3 Vdc HCMOS OUTPUT CHARACTERISTICS BSOV3S3 NOTE TABLE 3.0 PARAMETER Wash CW 0107 BSOV3S3 12.80M SURFACE MOUNT 3.3V HCMOS STRATUM 3 OCXO Cx032 PAGE 1 OF 2 REV: 03 DATE: 11/12/04 OCXO SERIES CENTER FREQUENCY Specifications subject to change without notice. aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. www.conwin.com PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1m inute transition. SOLDERING Pad Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 245°C ±5°C Solder pot dip, 95% Coverage. Solder Reflow: The component solder internal to this device has a melt ing point of 221°C, the peak temperature inside t he device should be less than or equal to 220°C for a maximum of 10 seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15mi nute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, half sine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. PIN FUNCTION .330 max (8.382mm) CW DATE CODE BSOV3S3 12.80M 1 7 8 14 CONTROL VOLTAGE GROUND (CASE) OUTPUT Vcc Dimensional Tolerance: ±.005 (.127mm) KEEP OUT AREA 90% .830 (21.08mm) 50% 10% .565 (14.35mm) CONTROL VOLTAGE 3.0Vdc POWER SUPPLY 3.3Vdc 14 8 1 7 Specifications subject to change without notice. DATA SHEET #: Cx032 PAGE 2 OF 2 REV: 03 DATE: 11/12/04 aCopyright 2001 Connor-Winfield all rights reserved.