THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722 WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS 14 PIN DIP 5.0V HCMOS STRATUM 3 OCVCXO with OVEN READY MONITOR ABSOLUTE MAXIMUM RATINGS TABLE 1.0 PARAMETER Storage Temperature UNITS MINIMUM -40 NOMINAL - MAXIMUM 85 UNITS °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Control Voltage (Vc) -0.5 - 7.0 Vdc OPERATING SPECIFIC ATIONS Center Frequency MINIMUM NOMINAL MAXIMUM UNITS 10 - 80 MHz -0.25 -4.6 - 0.25 4.6 ppm ppm (Fo) Frequency Stability Total Frequency Tolerance Operating Temperature Range 0 - 70 °C 4.75 5.00 5.25 Vdc Power Consumption (Vcc = 5.0V) - - 2.0 W Phase Jitter (BW =12KHz to 20MHz) - - 1 pS RMS Phase Jitter (BW =10Hz to 20MHz) - - 3 pS RMS Period Jitter - - 3 pS RMS SSB Phase Noise at 10Hz offset SSB Phase Noise at 10KHz offset Start Up Time: Oscillator - -75 -130 - 10 dBc/Hz dBc/Hz mS Warm Up Time - - 1 Minute TDEV @ 1.0 Sec. - - 1 nS TDEV @ 4.0 Sec. - - 2 nS Supply Voltage (Vcc) Control Voltage Range (Pin 1) MINIMUM NOMINAL MAXIMUM UNITS 0.5 2.5 4.5 Vdc +/-18 - +/-30 ppm 9 - - ppm/V (Vc) Frequency Pullability Slope of Frequency Adjust Input Impedance 100k - - Ohm Enable Voltage (Pin 3) (Vih) 2.0 - - Vdc Disable Voltage (Pin 3) (Vil) - - 0.8 Vdc MINIMUM - NOMINAL - MAXIMUM 15 UNITS pf Current (High) (Voh) 4.0 - - Vdc (Vol) - - 0.4 Vdc (High) (Ioh) -4 - mA (Low) (Ioh) - - 4 mA 45 50 55 % - - 6 nS Pin 12 - - 0.4 Vdc Pin 12 3.0 - - Vdc Duty Cycle measured at 1.5V PACKAGE CHARACTERISTICS Package Soldering Process 1 2 3 TABLE 3.0 NOTE 4 5.0V OPERATION FREQUENCY ADJUST TRI-STATE ENABLE / DISABLE FUNCTION LOW JITTER <1pS RMS FREQUENCY STABILITY: ±0.25ppm TABLE 4.0 (Low) Rise / Fall Time 10% to 90% Oven Ready Monitor voltage when oven is cold, not at operating temperature. Oven Ready Monitor voltage when oven is warm, at operating temperature. NOTE The Connor-Winfield EGOV5S3M is a hermetically sealed 14 Pin DIP 5.0V Oven Controlled, Voltage Controlled Crystal Oscillator (OCVCXO) with a Tri-State HCMOS output. The EGOV5S3M features an Oven Ready Monitor and is designed for Stratum 3 applications requiring low jitter and tight frequency stability. 5 HCMOS OUTPUT CHARACTERISTICS PARAMETER LOAD Voltage DESCRIPTION FEATURES INPUT CHARACTERISTICS PARAMETER EGOV5S3M NOTE TABLE 2.0 PARAMETER CW 0803 EGOV5S3M 80.0MHZ NOTE FREQUENCY TOLERANCE: ±4.6ppm TEMPERATURE RANGE: 0 to 70°C OVEN READY MONITOR HERMETICALLY SEALED PACKAGE RoHS COMPLIANT / LEAD FREE ORDERING INFORMATION TABLE 5.0 14 pin DIP, hermetically sealed, grounded case, welded package RoHS compliant, lead free. See solder profile on page 2. EGOV5S3M OCXO SERIES - 080.0M CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Cx061 PAGE 1 OF 2 REV: 02 DATE: 10/12/10 aCopyright 2008 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722 WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Notes: 1) Frequency vs. temperature stability, Vc = 2.50V. 2) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 10 years aging, Vc = 2.50V. 3) After one minute of operation at 25°C, the unit will be within +/-0.5ppm of its final stabilized frequency. The final stabilized frequency is that which is measured after 30 minutes of continuous operation at a stable 25°C ambient temperature. 4) Referenced to Fo @ 25°C, Positive Transfer Characteristic 5) Oscillator output is enabled with no connection on pin 3. ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C ±5°C for 20 Seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. Pin Connections Package Outline TABLE 6.0 .430 MAX Pin 1 3 7 8 12 14 (10.922mm) .200 (5.08mm) Dimensional Tolerance: ±.005 (.127mm) Test Circuit Connection Control Voltage Enable / Disable Ground (Case) Output Oven Monitor Vcc Solder Profile Temperature 260°C 260°C 220°C OVEN MONITOR REF. SUPPLY 4.5Vdc 14 5.0Vdc 12 180°C 150°C 8 120°C WW 1 20K POT 3 7 ENABLE/ CONTROL DISABLE VOLTAGE 0 120 S Max. Time 10 S 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Cx061 PAGE 2 OF 2 REV: 02 DATE: 10/12/10 aCopyright 2008 Connor-Winfield all rights reserved.