CURRENT 6.0 Amperes VOLTAGE 50 to 1000 Volts 6A05 THRU 6A100 Features · The plastic package carries Underwrites Laboratory Flammability Classification 94V-0 · High forward current capability · High surge current capability · Construction utilizes void-free molded plastic technique · High temperature soldering guaranteed : 250℃/10 seconds, 0.375"(9.5mm) lead length, 5 lbs, (2.3kg) tension P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. 0.360(9.1) 0.340(8.6) Mechanical Data · Case : P-6 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.07 ounce, 2.1 grams 1.0(25.4) MIN. 0.052(1.3) 0.048(1.2) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols 6A05 6A10 6A20 6A40 6A60 6A80 6A100 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=60℃ I(AV) 6.0 Amps Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) IFSM 400.0 Amps Maximum instantaneous forward voltage at 6.0A VF 1.1 Volts Maximum reverse current at rated voltage TA=25℃ TA=100℃ Typical thermal resistance (Note 2) Typical junction capacitance (Note 1) Operating and storage temperature range IR 10.0 100.0 RθJA 20.0 RθJL 4.0 CJ 150 TJ TSTG -50 to +175 Notes: (1) Measured at 1MHz and applied reverse voltage of 4.0V DC. (2) Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length, P.C.B. mounted with 1.1×1.1"(30×30mm) copper pads. μA ℃/W pF ℃ RATINGS AND CHARACTERISTIC CURVES 6A05 THRU 6A100 FIG.1-FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 5 1000 4 3 INSTANTANEOUS FORWARD CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 6 Ground pane 1" X 1" copper surface area PC BOARD Recommended PC Board Mounting PC Board 2 Standard PC Board mounting 1 0 0 20 40 60 80 100 120 140 160 180 200 LEAD TEMPERATURE ( ℃) FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 10 TJ=25℃ PULSE WIDTH=300μS 1 1% DUTY CYCLE 0.1 0.6 600 PEAK FORWARD SURGE CURRENT (AMPERES) 500 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 400 300 FIG.4-TYPICAL REVERSE CHARACTERISTICS 200 100 100 0 1 10 100 INSTANTANEOUS REVERSE CURRENT (μA) NUMBER OF CYCLES AT 60Hz FIG.5-TYPICAL THERMAL RESISTANCE VS LEAD LENGTH THERMAL RESISTANCE (℃/W) 30 25 20 10 TJ=100℃ 1.0 TJ=25℃ 0.1 15 10 0.01 0 20 40 60 80 100 5 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 EQUAL LEAD LENGTH TO HEAT SINK, (IN.) 0.8 0.9 1.0 120 140