CURRENT 10.0 Amperes VOLTAGE 50 to 1000 Volts 10A05 THRU 10A10 Features · The plastic package carries Underwrites Laboratory Flammability Classification 94V-0 · High forward current capability · High surge current capability · Construction utilizes void-free molded plastic technique · High temperature soldering guaranteed : 250℃/10 seconds, 0.375"(9.5mm) lead length, 5 lbs, (2.3kg) tension P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. 0.360(9.1) 0.340(8.6) Mechanical Data · Case : P-6 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.07 ounce, 2.1 grams 1.0(25.4) MIN. 0.052(1.3) 0.048(1.2) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols 10A05 10A1 10A2 10A4 10A6 10A8 10A10 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=50℃ I(AV) 10.0 Amps Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) IFSM 600.0 Amps Maximum instantaneous forward voltage at 10.0A VF 1.0 Volts Maximum reverse current at rated voltage TA=25℃ TA=100℃ Typical thermal resistance (Note 2) Typical junction capacitance (Note 1) Operating and storage temperature range IR 10.0 100.0 RθJA 20.0 RθJL 4.0 CJ 150 TJ TSTG -65 to +150 Notes: (1) Measured at 1MHz and applied reverse voltage of 4.0V DC. (2) Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length, P.C.B. mounted with 1.1×1.1"(30×30mm) copper pads. μA ℃/W pF ℃ RATINGS AND CHARACTERISTIC CURVES 10A05 THRU 10A10 FIG.1-FORWARD CURRENT DERATING CURVE FIG.2-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 10 8 INSTANTANEOUS FORWARD CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 12 6 4 2 0 0 20 40 60 80 100 120 140 160 180 200 LEAD TEMPERATURE ( ℃) FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 10 TJ=25℃ PULSE WIDTH=300μS 1 1% DUTY CYCLE 0.1 0.6 600 PEAK FORWARD SURGE CURRENT (AMPERES) 500 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 400 300 FIG.4-TYPICAL REVERSE CHARACTERISTICS 200 100 100 0 1 10 100 INSTANTANEOUS REVERSE CURRENT (μA) NUMBER OF CYCLES AT 60Hz FIG.5-TYPICAL THERMAL RESISTANCE VS LEAD LENGTH THERMAL RESISTANCE (℃/W) 30 25 20 10 TJ=100℃ 1.0 TJ=25℃ 0.1 15 10 0.01 0 20 40 60 80 100 5 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 EQUAL LEAD LENGTH TO HEAT SINK, (IN.) 0.8 0.9 1.0 120 140