TI SN65LBC031D

SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
D
D
D
D
D
D
SN75LBC031 Meets Standard ISO/DIS
11898 (up to 500 k Baud)
Driver Output Capability at 50 mA
Wide Positive and Negative Input/output
Bus Voltage Range
Bus Outputs Short-Circuit-Protected to
Battery Voltage and Ground
Thermal Shutdown
Available in Q-Temp Automotive
– HighRel Automotive Applications
– Configuration Control/Print Support
– Qualification to Automotive Standards
description
D PACKAGE
(TOP VIEW)
TX
GND
VCC
RX
1
8
2
7
3
6
4
5
ASC
CANH
CANL
REF
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
TX
GND
VCC
Transmitter input
Ground
Supply voltage
RX
Receiver output
REF
Reference output
CANL
Low side bus output driver
The SN75LBC031 is a CAN transceiver used as
CANH
High side bus output driver
an interface between a CAN controller and the
ASC
Adjustable slope control
physical bus for high speed applications of up to
500 kBaud. The device provides transmit
FUNCTION TABLE
capability to the differential bus and differential
CANH
CANL BUS STATE RX
TX
receive capability to the controller. The transmitter
L
H
L
Dominant
L
outputs (CANH and CANL), feature internal
High or floating Floating Floating Recessive
H
transition regulation to provide controlled
L = low, H = high
symmetry resulting in low EMI emissions. Both
transmitter outputs are fully protected against battery short circuits and electrical transients that can occur on
the bus lines. In the event of excessive device power dissipation the output drivers are disabled by the thermal
shutdown circuitry at a junction temperature of approximately 160°C. The inclusion of an internal pullup resistor
on the transmitter input ensures a defined output during power up and protocol controller reset. For normal
operation at 500 kBaud the ASC terminal is open or tied to GND. For slower speed operation at 125 kBaud the
bus output transition times can be increased to reduce EMI by connecting the ASC terminal to VCC. The receiver
includes an integrated filter that suppresses the signal into pulses less than 30 ns wide.
The SN75LBC031 is characterized for operation from –40°C to 85°C. The SN65LBC031 is characterized for
operation from –40°C to 125°C. The SN65LBC031Q is characterized for operation over the automotive
temperature range of – 40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2000, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
logic diagram
VCC
ASC
R
R
R3
CANH
TX
CANL
R2
R1
2R
REF
2R
R1
RX
R
R
GND
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Logic supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Bus terminal voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 5 V to 20 V
Input current at TX and ASC terminal, II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Input voltage at TX and ASC terminal, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 × VCC
Operating free-air temperature range, TA: SN65LBC031, SN65LBC031Q . . . . . . . . . . . . . . . – 40°C to125°C
SN75LBC031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Operating juncation range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Continuous total power dissipation at (or below) 25°C free-air temperature . . See Dissipation Rating Table
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 10 sec TC, D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values, except differential bus voltage, are measured with respect to GND.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
OPERATING FACTOR
ABOVE TC = 25°C
TC = 125°C
POWER RATING
D
725 mW
5.8 mW/°C
145 mW
DISSIPATION DERATING CURVE
vs
FREE-AIR TEMPERATURE
PD – Maximum Continuous Dissipation – mW
1200
TC = 25°C
1000
P = 8.8 mW/°C
800
600
D = 5.8 mW/°C
400
200
0
25
35
45
55
65
75
85
95
105 115 125
TA – Free-Air Temperature – °C
Figure 1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
recommended operating conditions
MIN
NOM
MAX
4.5
5
5.5
V
Logic supply voltage, VCC
Voltage at any bus terminal (separately or common mode), VI or VIC (see Note 3)
UNIT
–2
7
V
High-level input voltage, VIH
TX
2
V
Low-level input voltage, VIL
TX
0
VCC
0.8
–50
mA
–400
µA
Transmitter
High level output current,
High-level
current IOH
Receiver
Transmitter
Low level output current
Low-level
current, IOL
50
Receiver
Operating free-air
free air temperature,
temperature TA
1
SN75LBC031
–40
85
SN65LBC031, SN65LBC031Q
–40
125
V
mA
°C
NOTES: 2. All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
3. For bus voltages from –5 V to –2 V and 7 V to 20 V the receiver output is stable.
SYMBOL DEFINITION
DATA SHEET PARAMETER
DEFINITION
VO(CANHR)
VO(CANLR)
CANH bus output voltage (recessive state)
VO(CANHD)
VO(CANLD)
CANH bus output voltage (dominant state)
VO(DIFFR)
VO(DIFFD)
Bus differential output voltage (recessive state)
VI(ASC)
Adjustable slope control input voltage
CANL bus output voltage (recessive state)
CANL bus output voltage (dominant state)
Bus differential output voltage (dominant state)
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IREF = ± 20 µA
VO(REF)
RO(REF)
Reference source output voltage
ICC(REC)
ICC(DOM)
Logic supply current, recessive state
4
Reference source output resistance
Logic supply current, dominant state
POST OFFICE BOX 655303
See Figure 2,
2 S1 closed
• DALLAS, TEXAS 75265
MIN
TYP
MAX
UNIT
0.45 VCC
0.55 VCC
V
5
10
kΩ
12
20
55
80
mA
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
transmitter electrical characteristics over recommended ranges of supply and operating free-air
temperature (unless otherwise noted)
PARAMETER
VO(CANHR)
VO(CANLR)
TEST CONDITIONS
Output voltage (recessive state)
See Figure
g
2,,
MIN
2
S1 open
TYP
0.5VCC
MAX
3
V
mV
VO(DIFFR)
VO(CANHD)
Differential output voltage (recessive state)
–500
0
50
Output voltage (dominant state)
2.75
3.5
4.5
VO(CANLD)
VO(DIFFD)
Output voltage (dominant state)
0.5
1.5
2.25
See Figure 2,
S1 closed
Differential output voltage (dominant state)
1.5
UNIT
2
3
–100
–185
V
IIH(TX)
High level input current (TX)
High-level
VIH = 2.4 V
VIH = VCC
IIH(ASC)
High level input current (ASC)
High-level
VIH = 2.4 V
VIH = VCC
100
165
200
340
IIL(TX)
IIL(ASC)
Low-level input current (TX)
VIL = 0.4 V
VIL = 0.4 V
–180
–400
µA
15
25
µA
CI(TX)
TX input capacitance
IO(ssH)
IO(ssL)
CANH short circuit output current
Low-level input current (ASC)
±2
8
VO(CANH) = –2 V to 20 V
VO(CANL) = 20 V to –2 V
CANL short circuit output current
µA
µA
pF
–95
–200
mA
140
250
mA
NOTE 2: All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
transceiver dynamic characteristics over recommended operating free-air temperature range and
VCC = 5 V
PARAMETER
t(loop)
(l
)
SR(RD)
SR(DR)
Loop time
Differential-output slew rate
(recessive to dominant)
Differential-output slew rate
(dominant to recessive)
MAX
UNIT
See Figures 2 and 3,
S1 closed,
TEST CONDITIONS
VI(ASC) = 0 V or open circuit,
S2 open
280
ns
See Figures 2 and 3,
S1 closed,
VI(ASC) = VCC,
S2 closed
400
ns
See Figures 2 and 4,
S1 closed,
VI(ASC) = 0 or open circuit,
S2 open
35
V/µs
See Figures 2 and 4,
S1 closed,
VI(ASC) = VCC,
S2 closed
10
V/µs
See Figures 2 and 4,
S1 closed,
VI(ASC) = 0 or open circuit,
S2 open
10
V/µs
See Figures 2 and 4,
S1 closed,
VI(ASC) = VCC,
S2 closed
10
V/µs
S1 closed
td(RD)
td(DR)
Differential output delay time
Differential-output
See Figure 2
2,
tpd(RECRD)
tpd(RECDR)
Receiver propagation
g
delay
y
time
See Figures 2 and 5
MIN
TYP
55
ns
160
ns
90
ns
55
ns
NOTE 4: Receiver input pulse width should be >50 ns. Input pulses of <30 ns are suppressed.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
receiver electrical characteristics over recommended ranges of common-mode input voltage,
supply voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT(REC)
VIT(DOM)
Differential input threshold voltage for recessive state
Vhys
Recessive-dominant input hysteresis
MIN
MAX
500
VIC = –2
2 V to 7 V
Differential input threshold voltage for dominant state
TYP
900
100
180
UNIT
mV
mV
VOH(RX)
High-level output voltage
VO(DIFF) = 500 mV,
IOH = –400 µA
VOL(RX)
Low-level output voltage
VO(DIFF) = 900 mV,
IOL = 1 mA
rI(REC)
CANH and CANL input resistance in recessive state
rI(DIFF)
Differential CANH and CANL input resistance in recessive
state
Ci
CANH and CANL input capacitance
20
pF
Ci(DHL)
Differential CANH and CANL input capacitance
10
pF
VCC–0.5 V
VCC
V
0
0.5
V
dc, no load
5
50
kΩ
dc, no load
10
100
kΩ
NOTE 2: All voltage values, except differential bus voltage, are measured with respect to the ground terminal.
PARAMETER MEASUREMENT INFORMATION
S2
VCC
60 Ω
60 Ω
ASC
TX Input
CANH
S1
VDIFF
CANL
Generator
(see Note A)
R
56 pF
60 Ω
60 Ω
56 pF
RX Output
15 pF
NOTE A: The input pulse is supplied to TX by a generator having a tr and tf = 5 ns.
Figure 2. Test Circuit
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
PARAMETER MEASUREMENT INFORMATION
3V
TX Input
3V
1.5 V
TX Input
0V
90%
RX Output
10%
1.5 V
0V
VOH
80%
VO(DIFF)
VOL
20%
20%
tloop
tloop
VOH
80%
VOL
SR(DR)
SR(RD)
Figure 3. Loop Time
Figure 4. Slew Rate
NOTE A: The input pulse is supplied to TX by a generator having a tr and tf = 5 ns.
0.9 V
VO(DIFF)
0.5 V
90%
RX Output
10%
tpd(RECDR)
tpd(RECRD)
NOTE A: The input pulse is supplied as VDIFF using CANH and CANL
respectively by a generator having a tr and tf = 5 ns.
Figure 5. Receiver Delay Times
100 pF
CANH
Transient Source
(Schaffner Generator)
R(SOURCE)
60 Ω
100 pF
VS
CANL
Figure 6. Transient Stress Capability Test Circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
VS – Transient Magnitude – %
PARAMETER MEASUREMENT INFORMATION
Transient Magnitude
vs
Time
VS
90%
10%
0V
t – Time
tr
td
t2
t1
Figure 7. Transient Stress Capability Waveform
Table 1. Test Circuit Results According to DIN 40839
SOURCE
IMPEDANCE
RSOURCE
10 Ω
PULSE WIDTH
td
(see Note 5)
PULSE RISE
TIME, tr
(see Note 6)
PULSE TIME,
t2
(see Figure 7)
REPETITION
PERIOD, t1
(see Figure 7)
NUMBER OF
PULSES
1
TRANSIENT
MAGNITUDE
VS
–100 V
2 ms
1 µs
200 ms
5s
5000
2
100 V
10 Ω
50 µs
1 µs
200 ms
5s
5000
3a
–150 V
50 Ω
0.1 µs
5 ns
100 µs
100 µs
See Note 7
3b
100 V
50 Ω
0.1 µs
5 ns
100 µs
100 µs
See Note 7
5
60 V
1Ω
400 ms
5 ms
—
—
1
TEST PULSE
NOTES: 5. Measured from 10% on rising edge to 10% on falling edge
6. Measured from 10% to 90% of pulse
7. Pulse package for a period of 3600 s, 10 ms pulse time, 90 ms stop time
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
APPLICATION INFORMATION
5V
100 nF
3
VCC
VCC
TL7705B
7
2
8
ASC
CANH
7
SENSE
SN75LBC031
RESIN
RESET
3
120 Ω
10 kΩ
8
10 kΩ
Ct
REF
GND
1
4
5
2
6
GND
CANL
Cin
REF
TX
0.1 µF
1
5
RX
120 Ω
4
CAN Microcontroller
Figure 8. Typical SN75LBC031 Application
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN65LBC031, SN65LBC031Q, SN75LBC031
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
SLRS048A – MAY 1998 – REVISED APRIL 2000
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A.
B.
C.
D.
10
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
SN65LBC031D
ACTIVE
SOIC
D
8
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
-40 to 85
6LB031
SN65LBC031DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
6LB031
SN65LBC031DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
6LB031
SN65LBC031P
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
-40 to 85
SN75LBC031D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
7LB031
SN75LBC031DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
7LB031
SN75LBC031P
OBSOLETE
PDIP
P
8
TBD
Call TI
Call TI
0 to 70
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
SN75LBC031DR
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.4
B0
(mm)
K0
(mm)
P1
(mm)
5.2
2.1
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN75LBC031DR
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated