EM MICROELECTRONIC - MARIN SA 365324.CP37 / B SPECIFICATION FOR OLED MODULE TAT07 TABLE OF CONTENTS 1. 2. PURPOSE ..........................................................................................................................................................2 PRODUCT SPECIFICATIONS...........................................................................................................................2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 3. QUALIFICATION PROCEDURE .......................................................................................................................7 3.1 3.2 4. 5. Conformity ................................................................................................................................................................8 Responsibility ...........................................................................................................................................................8 Shipping Inspection Standards.................................................................................................................................9 7.3.1 Shipping Inspection Standards................................................................................................................9 7.3.2 Zone Definitions ......................................................................................................................................9 7.3.3 Visual Inspection .....................................................................................................................................9 7.3.4 Limit Sample............................................................................................................................................9 7.3.5 Individual Appearance Defects Standards (Back light ON and OFF / Display OFF) .............................10 7.3.6 Individual appearance defects standards (display ON) .........................................................................11 7.3.7 Chipped Glass Defect Standard ............................................................................................................12 7.3.8 FPC .......................................................................................................................................................13 OPERATIONS PRECAUTIONS ......................................................................................................................14 8.1 8.2 8.3 8.4 8.5 9. 10. 11. 12. 13. Internal Packaging....................................................................................................................................................8 RECEIVING INSPECTION.................................................................................................................................8 QUALITY ASSURANCE ....................................................................................................................................8 7.1 7.2 7.3 8. Tests to be performed on prototypes, preserie.........................................................................................................7 Packing reliability......................................................................................................................................................8 MARKINGS ........................................................................................................................................................8 SHIPMENT METHOD ........................................................................................................................................8 5.1 6. 7. Module Revision and ordering number.....................................................................................................................2 Basic Specification ...................................................................................................................................................2 Mechanical Characteristics ......................................................................................................................................2 Absolute Maximum Ratings......................................................................................................................................2 Electrical Characteristics ..........................................................................................................................................3 LCD Electrical & Optical characteristics ...................................................................................................................3 2.6.1 Definition of optical characteristics ..........................................................................................................4 2.6.2 Definition of viewing angle.......................................................................................................................5 2.6.3 Definition of response time ......................................................................................................................5 Mechanical drawing..................................................................................................................................................6 2.7.1 Pin connection (signal function)...............................................................................................................7 Safety .....................................................................................................................................................................14 Handling .................................................................................................................................................................14 Mounting and Design .............................................................................................................................................14 Storage...................................................................................................................................................................14 Cleaning .................................................................................................................................................................14 APPENDIX 1: PLASTIC TRAY DRAWING .....................................................................................................15 APPENDIX 2: PALLET ASSEMBLY DRAWING ...........................................................................................16 SPECIFICATION HISTORY.............................................................................................................................17 ATTACHMENTS ..............................................................................................................................................17 CUSTOMER APPROVAL ................................................................................................................................17 This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 1 of 17 365324.CP37 / B 1. PURPOSE This specification covers the delivery requirements for the display module delivered by EM MicroelectronicMarin SA. 2. PRODUCT SPECIFICATIONS 2.1 MODULE REVISION AND ORDERING NUMBER EM Part Number TAT07_R01 2.2 Customer Part Number TBD BASIC SPECIFICATION ITEM Display technology Layout LCD Driver Interface LCD Module structure Estimated useful life time at ambient conditions 2.3 CHARACTERISTICS OLED monochrome, color yellow Dot matrix SSD1305Z Selectable with BS2 and BS1 signals COG+FPC 60 khours operating until half brightness 80 khours storage MECHANICAL CHARACTERISTICS ITEM Dots configuration Dots dimensions (mm) Dots gap (mm) Module size (L x W x T, mm) Panel size Diagonal AA size Weight (g) 2.4 Remarks Initial revision CHARACTERISTICS 128 x 64 0.254 (L) x 0.254 (W) 0.020 40.3 (L) x 63.3 (W) x 2.01 (T) 40.3 (L) x 27.3 (W) x2.01 (T) 1.54" TBD ABSOLUTE MAXIMUM RATINGS Item Power supply voltage Supply voltage Operating temperature Storage temperature Operating & storage humidity Symbol Vdd Vcc Topr Tstg RHoprstg Condition 25 °C 25 °C ------- Vss = 0 V, Ambient Temp.= 25 °C Min Max Unit -0.3 +3.5 V 8 16 V 0 +50 °C -20 +70 °C 0 85 %RH This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 2 of 17 365324.CP37 / B 2.5 ELECTRICAL CHARACTERISTICS Item Power supply voltage OLED operating voltage Symbol VDD Vcc Idd Current consumption Icc 2.6 Condition 25 °C 25 °C 25 °C VDD = Typ. VCC = Typ. Contrast setting = 0xFF 100% Display ON Vss = 0 V, Ambient Temp.= 25 °C Min Typ Max Unit 2.4 3.0 3.5 V 12.5 V - 130 tbd μA - 10.5 tbd mA LCD ELECTRICAL & OPTICAL CHARACTERISTICS ITEM Contrast Ratio SYMBOL *CR CONDITIONS Driving conditions TEMP 25°C Brightness Viewing angle B θ, X axis θ, Y axis ton Driving conditions Driving conditions CR > 2 25°C 25°C Driving conditions Driving conditions Driving conditions Driving conditions Driving conditions 25°C 0°C 100 10 - 25°C 0°C 10 - Response time toff MIN -80 -80 TYP 500 MAX - +80 +80 UNIT cdlm2 deg. µs - - This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 3 of 17 365324.CP37 / B 2.6.1 Definition of optical characteristics Z(Θ=0°) Detector Light (when reflected) θ1 θ Y’(Φ=180°) θ2 X’(Φ=270°) X(Φ=90°) Φ Y(Φ=0°) Light (when transmitted) Definition of contrast Cr. Bright (%) Brightness Cr. = B2 = B1 = Brightness of selected segment Brightness of not selected segment B2 Brightness curve of selected segment B1 Dark Operating voltage (V) This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 4 of 17 365324.CP37 / B 2.6.2 Definition of viewing angle Definition of viewing angle θ Cr.max optimum vision with the naked eye and viewing angle θ at CR. max above are not always the same Cr.=2 phi=180° 2.6.3 −θ +θ phi=0° Definition of response time Definition of response time 1/fFRM Voltage (V) V opr 0 Bright Brightness (reflection) Unselected state (display OFF) Selected state (display ON) 100% Unselected state (display OFF) 90% 10% Dark ton Vopr:Operating voltage (V) fFRM;Frame frequency (Hz) toff ton:Response time (rise) (ms) toff:Response time (fall) (ms) This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 5 of 17 365324.CP37 / B 2.7 MECHANICAL DRAWING This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 6 of 17 365324.CP37 / B 2.7.1 Pin connection (signal function) See mechanical drawing 3. QUALIFICATION PROCEDURE 3.1 TESTS TO BE PERFORMED ON PROTOTYPES, PRESERIE Test ref. Test name Test conditions Test condition Critieria MC Mechanical characterization Complete critical mechanical dimension report (once for all with first article inspection report and each time major modification is done). 25°C 0 defects Idd, Vcc (once for all with first article inspection report and each time major modification is done). Brightness, contrast (once for all with first article inspection report and each time major modification is done) Display to be controlled visually for brightness over all operating temperature ranges. 25°C Operating temperature range Driving mode Readable, over operating temperature, 0 defects Functional, brightness ≥ 50% of initial value, current consumption < 2x initial value, 0 defects Functional, brightness ≥ 50% of initial value, current consumption < 2x initial value, 0 defects Functional, 0 defects EC OC VT Electrical characterization Optical characterization Visual test in all operating temperature ranges 25°C TST Thermal shock test -20°C to 70°C, 5 cycles , 2h/2h, transfer time 1min @ 25°C Non driving mode AHTO Accelerated humidity test operating 40°C / 85% RH 240 hours Driving mode Vibration test Frequency range: 5-500 Hz 2 5Hz: 0.10 (m/s ) 2/Hz 12Hz: 2.20 (m/s2) 2/Hz 2 20Hz: 2.20 (m/s ) 2/Hz 200Hz: 0.04 (m/s2) 2/Hz 2 500Hz: 0.04 (m/s ) 2/Hz Duration 2 hours in each direction (X, Y, Z) Operating mode: ON 70°C / 16h 25°C (test will be performed by customer) RV DH C Dry heat Cold -20°C / 16h Intermittent driving Intermittent driving Prototypes (pcs) Preserie (pcs) 10 30 10 30 2 2 2 2 10 10 10 10 5 5 5 5 5 5 0 defects 0 defects Hot start, functional, readable Cold start (no condensation), functional, readable This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 7 of 17 365324.CP37 / B 3.2 PACKING RELIABILITY The internal and external packaging has to be released and qualified by following tests: Condition Take one external box filled with the required inner boxes completed with LCD products Take 5 empty trays Damp heat with load 4. Test Drop the external box from 0.8m on concrete: - 6 side - 8 corners 70°C 96 hours -20°C 96 hours 20-40°C, 80-90% HR, 168h, 2 stacked full boxes Acceptable results 1) No mechanical & appearance damage on the finished product. 2) No product out of their original position. No deformation of trays No damage to internal products and no major deformation of the trays MARKINGS Each modules is individually labelled with following instructions : - TAT07_Rx (x: current revision 0, 1, 2, etc - see §2.1) - Lot number : Y.WW.SS (Year.Week.Serial number) For label size and location refer to mechanical drawing (§2.7) 5. SHIPMENT METHOD 5.1 6. INTERNAL PACKAGING The products are packaged on ESD safe trays (see tray drawing in Appendix 1), to protect them from touching each other. Tray dimension is 33.5 x 33.5mm, each tray containing? pcs. Maximum stacking height for sub packages shall be limited to 10 trays + 1 cover tray. Following information is contained on the label of each subpackage: 1. Lot number 2. P.N. (TAT07_Rx) (see §2.1) 3. Customer P.N. (see §2.1) 4. Quantity of pcs RECEIVING INSPECTION Receiving inspection at customer site has to be done within 1 month after receipt of the goods. Any products that do not conform to product and delivery specification are dealt with in accordance with item « dealing with customer complaints » in EM General Terms of Sales (see EM website) 7. QUALITY ASSURANCE Also refer to EM General Terms of Sales and EM Web Site 7.1 CONFORMITY The performance, functions and reliability of the shipped products conform to the EM product specifications. 7.2 RESPONSIBILITY Customer is responsible for any defects in quality caused after receiving inspection. This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 8 of 17 365324.CP37 / B 7.3 SHIPPING INSPECTION STANDARDS 7.3.1 Shipping Inspection Standards Sampling size : MIL_STD_105D, single sampling, Inspection level II RANK Major defect Minor defect 7.3.2 DEFECT No display Short circuit Outside dimensions Display missing Pattern misalignment Spots, streaks Bubbles Chromaticity and uniformity Polarizer defects Glass defects Dirt, spots Current consumption FPC AQL level 0.1 0.65 Zone Definitions Shipment inspection is performed under dividing zone A and B. A Viewing area B Outside viewing area 7.3.3 Visual Inspection Inspect under 30W fluorescent lamp, leaving 30cm between panel and eyes, and between panel and lights. Display 7.3.4 Limit Sample If a judgement cannot be made according to the delivery specification, limit samples must be agreed on and used. This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 9 of 17 365324.CP37 / B 7.3.5 Individual Appearance Defects Standards (Back light ON and OFF / Display OFF) Φ Average diameter (mm), W: Width (mm), L: Length (mm) No Item 1 Spots Details Section <Φ≤ <Φ≤ 0.10 0.20 2 0.10 0.20 <Φ≤ Total number of defects Streaks 1 3 Any number* W≤ 0.01 W ≤ 0.03 W ≤ 0.05 Standards, max no. of defects / module Zone A Zone B Any number* Any number 2 L ≤ 2.0 L ≤ 1.0 Other than above Total number of detects 3 4 Chromaticity and Uniformity Bubbles in polarizer Scratches / dent on the polarizer limit sample Bubbles between polarizer and glass 0.20 < Φ ≤ 0.50 0.50 < Φ ≤ 1.0 3 1 Any number Any number 1.0 < Φ 0 2 1 Any number Any number Any number Any number* 3 Any number L ≤ 5.0 L ≤ 10.0 0.10 <Φ≤ <Φ≤ 0.10 0.25 0.25 <Φ≤ 0.30 0.30 <Φ Spots Lines 6 7 0 3 Streaks and uneven colour W ≤ 0.15 W ≤ 0.15 5 Any number 2 1 1 0 Same as N°2 See N.1, 2 Dirt on the polarizer Polarizer dislocation Products pass if the dislocation is out of viewing area * not counted in total number of acceptable defects. Total number of acceptable defects = 3 This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 10 of 17 365324.CP37 / B 7.3.6 No 1 2 Individual appearance defects standards (display ON) Item No display Display missing Detail Section (mm) Standard. Max No of defects / module Part or all of the screen doesn’t light because of an open or a short circuit Must not occur. For W, ref. drawing 2.8 Part of display segment missing because of pin holes or an open. Φ Φ ≤ 0.10 Any number 0.10 < Φ ≤ 0.20 2 0.20 < Φ 1 W 3 Display missing Part of display segment missing because of pin holes or an open. Part missing ≤ 1/3 of pixel area a 3 pixels b W No Item 7 Current consumption (Ic) Detail Condition: - all pixels ON - driving conditions typ. - 25°C Specification Standards, max no. of acceptable defects / module According to table 2.5 0 This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 11 of 17 365324.CP37 / B 7.3.7 No Chipped Glass Defect Standard Item Details Section at Standards, max no. of defects / module More than 80% of lead terminal must remain 1 Chipped glass lead terminals 2 Chipped excluding terminals 3 Chipped glass end face 4 Chipped glass Other cases Acceptable if : - 100% of lead terminal remain - 100% of seal remain 5 Glass rest or insulating layer b≤h/3 6 Irregular cut b≤h/3 No glass rest glass lead viewing area on Acceptable if the distance d between chip and the limit of the viewing area is ≥ 0.25mm Width ’s’ of seal remaining must be ≥0.5mm; ‘c’ must be <10.0mm This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 12 of 17 365324.CP37 / B No 7.3.8 FPC 7.3.8.1. Adhesion Item Detail Specification Peel off speed = 20mm/minute FPC 1 F ave >= 500 N/m Where “F ave” is the average peel off strength obtained in “soldered area” Pull off strength between FPC and Display terminals Residue ≥ 50% of bond width DISPLAY 2 Display and FPC terminals misalignment --- Contact area reduction <= 25% of total contact area 7.3.8.2. Characteristics No Item Detail Specification 1 Outline cable dimension and pattern dimension and layout --- According to assembly drawing Not acceptable if present on terminals area and on external edge of cable. In other positions, acceptable if diameter <= distance between 2 adiacent tracks 2 Bubble between base material and coverlayer --- 3 Detachment between track and base material --- Not allowed 4 Permanent bend and scratch --- Not allowed This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 13 of 17 365324.CP37 / B 8. OPERATIONS PRECAUTIONS 8.1 SAFETY • If the display panel breaks, be careful not to get the residues in your mouth or in your eyes. • If the residues touch your skin or clothes, wash it off using soap and water. 8.2 HANDLING • The display is plate glass; do not hit or crush it. • The polarizer of the display is very fragile; handle it very carefully. • Do not soil or damage the display terminals. • Keep the display surface clean. Do not touch it with your skin. • Display module is ESD sensitive, to be handled with usual ESD precautions. 8.3 MOUNTING AND DESIGN • If any force is applied to the polarizer, bubbles or separation may occur. • Leave a gap so that the display, excluding the fixing portion, does not touch other components. • Make a window smaller than the viewing area. • To protect the display from external pressure, place a transparent plate (acrylic or glass) over the display surface having a small gap. • Avoid condensation, otherwise the transparent electrodes may break. 8.4 STORAGE • For long-time storage, keep in a dark place at 25°C ± 10°C, 65% RH maximum. • Do not store the display near organic solvents or corrosive gases. 8.5 CLEANING • Do not wipe the polarizing plate with a dry cloth, as it may scratch the surface. • Wipe the module gently with a soft cloth soaked with a perfluorine-hexane or iso-propanol. • Do not use ketonic solvents (ketone and acetone) or aromatic solvents (toluene and xylene), as they may damage the plastic cover plate. This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 14 of 17 365324.CP37 / B 9. - APPENDIX 1: PLASTIC TRAY DRAWING Drawing to be done Tray dimensions: 335 x 335 x 11.8 ESD safe material Vacuum forming technology This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 15 of 17 365324.CP37 / B 10. APPENDIX 2: PALLET ASSEMBLY DRAWING This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 16 of 17 365324.CP37 / B 11. SPECIFICATION HISTORY Rev. E.C.N. Pages Date Resp. A 07-0287 17 27.03.07 LON B 08-0301 3 04.04.08 FABR Description 1st revision Updated value in point 2.5 electrical characteristics 12. ATTACHMENTS Minispecs: - Forms: - 13. CUSTOMER APPROVAL Should EM not have received a written feed-back from you within 10 days from receipt of the above specification(s), such specification(s) shall be explicitly considered as approved and accepted by you. Customer (print company name): _______________________________________ Approved by (print name): _______________________________________ Signature: _______________________________________ Title: _______________________________________ Date: _______________________________________ Please complete and return to: LCD & Module Department EM Microelectronic SA Rue des Sors 3 CH-2074 Marin Fax: +41 32 755 5918 This document is the property of EM MICROELECTRONIC-MARIN SA and is furnished in confidence and upon the condition that all rights originating in the information, whether patented or not, will be respected. EM Document Center/04.08 - Page 17 of 17