TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Ultra Low Power Stereo Audio Codec Check for Samples: TLV320AIC3206 FEATURES • • • APPLICATIONS 1 2 • • • • • • • • • • • Stereo Audio DAC with 100dB SNR 5.8mW Stereo 48ksps DAC-to-Ground-Centered Headphone Playback Stereo Audio ADC with 93dB SNR 5.2mW Stereo 48ksps ADC Record PowerTune™ Extensive Signal Processing Options Six Single-Ended or 3 Fully-Differential Analog Inputs Stereo Analog and Digital Microphone Inputs Ground-Centered Stereo Headphone Outputs Very Low-Noise PGA Low Power Analog Bypass Mode Programmable Microphone Bias Programmable PLL • • • • • 5mm x 5mm 40-pin QFN Package Portable Navigation Devices (PND) Portable Media Player (PMP) Mobile Handsets Communication Portable Computing DESCRIPTION The TLV320AIC3206 (sometimes referred to as the AIC3206) is a flexible, low-power, low-voltage stereo audio codec with programmable inputs and outputs, PowerTune capabilities, fixed predefined and parameterizable signal processing blocks, integrated PLL and flexible digital interfaces. IN1_L IN2_L IN3_L 0…+47.5 dB + Left ADC tpl + * AGC DRC ADC Signal Proc. DAC Signal Proc. Vol . Ctrl * -6...+14dB + Left DAC HPL 1dB steps Gain Adj. 0.5 dB steps -6...+29dB -30...0 dB LOL + 1dB steps Data Interface -6...+29dB -30...0 dB LOR + 1dB steps 0… +47.5 dB + Gain Adj. Right ADC IN3_R + tpr * 0.5 dB steps IN2_R ADC Signal Proc. DAC Signal Proc. AGC DRC * -6...+14dB Right DAC HPR + 1dB steps Vol . Ctrl IN1_R GND_Sense SPI_Select SPI / I2C Control Block Reset MicBias MicDet Ref PLL Dig Mic Inter rupt Sec. I2S I/F Primary I2S Interface VNEG Charge Pump Mic Bias Supplies Fly_N Fly_P Pin Muxing / Clock Routing Ref DVDD_CP DVSS_CP BCLK WCLK DIN DOUT GPIO MCLK SCLK MISO SDA/MOSI SCL/SS IOVss (GND) DVss (GND) Avss (GND) GND IOVdd AVdd DVdd AVdd DRVdd_HP Figure 1. Simplified Block Diagram 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerTune is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010, Texas Instruments Incorporated TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. DESCRIPTION (CONTINUED) The TLV320AIC3206 features extensive register-based control of power, input/output channel configuration, gains, effects, pin-multiplexing and clocks is included, allowing the device to be precisely targeted to its application. The device can cover operations from 8kHz mono voice playback to audio stereo 192kHz DAC playback, making it ideal for portable battery-powered audio and telephony applications. The record path of the TLV320AIC3206 covers operations from 8kHz mono to 192kHz stereo recording, and contains programmable input channel configurations covering single-ended and differential setups, as well as floating or mixing input signals. It also includes a digitally-controlled stereo microphone preamplifier and integrated microphone bias. Digital signal processing blocks can remove audible noise that may be introduced by mechanical coupling, e.g. optical zooming in a digital camera. The playback path offers signal-processing blocks for filtering and effects, and supports flexible mixing of DAC and analog input signals as well as programmable volume controls. The playback path contains two high-power output drivers which eliminate the need for ac coupling capacitors. A built in charge pump generates the negative supply for the ground centered high powered output drivers. The high-power outputs can be configured in multiple ways, including stereo and mono BTL. The device can be programmed to various power-performance trade-offs. Mobile applications frequently have multiple use cases requiring very low power operation while being used in a mobile environment. When used in a docked environment power consumption typically is less of a concern, while minimizing noise is important. The TLV320AIC3206 addresses both cases. The device offers single supply operation from 1.5V-1.95V. Digital I/O voltages are supported in the range of 1.1V-3.6V. The required internal clock of the TLV320AIC3206 can be derived from multiple sources, including the MCLK pin, the BCLK pin, the GPIO pin or the output of the internal PLL, where the input to the PLL again can be derived from the MCLK pin, the BCLK or GPIO pins. Although using the PLL ensures the availability of a suitable clock signal, it is not recommended for the lowest power settings. The PLL is highly programmable and can accept available input clocks in the range of 512kHz to 50MHz. The device is available in the 5mm × 5mm, 40-pin QFN package. 2 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Package and Signal Descriptions Packaging/Ordering Information PRODUCT PACKAGE PACKAGE DESIGNATOR OPERATING TEMPERATURE RANGE TLV320AIC3206 QFN RSB –40°C to 85°C ORDERING NUMBER TRANSPORT MEDIA, QUANTITY RSBT Tape and Reel, 250 RSBR Tape and Reel, 3000 IOVdd DOUT/MFP2 WCLK DIN/MFP1 MCLK BCLK DVss Reset GPIO/MFP5 DVss (1) Pin Assignments DVdd (40) IOVss DVdd_CP FLY_P SCLK/MFP3 DVss_CP SDA/MOSI SCL/SSZ FLY_N MISO/MFP4 VNEG SPI_SELECT MICDET IN1_L HPR IN1_R DRVDD_HP IN2_L HPL IN2_R REF AVss IN3_L MICBIAS IN3_R LOR LOL AVdd GND_Sense AVdd Figure 2. QFN (RSB) Package, Bottom View Table 1. TERMINAL FUNCTIONS 5x5mm 40-PIN QFN (RSB) PIN NO. – NAME TYPE 1 – DVss GND Digital ground. Device substrate. (1) 2 – DVss GND Digital ground (1) 3 – RESET I Hardware reset 4 – GPIO I/O DESCRIPTION Primary General purpose digital IO MFP5 Secondary CLKOUT output INT1 output INT2 output Audio serial data bus ADC word clock output Audio serial data bus (secondary) bit clock output Audio serial data bus (secondary) word clock output Digital microphone clock output 5 (1) – MCLK I Master clock input The DVss pins are not connected within the device: Must be connected on the PC board. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 3 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Table 1. TERMINAL FUNCTIONS (continued) 5x5mm 40-PIN QFN (RSB) PIN NO. – NAME TYPE 6 – BCLK I/O Audio serial data bus (primary) bit clock 7 – WCLK I/O Audio serial data bus (primary) word clock 8 – DIN I DESCRIPTION Primary function Audio serial data bus data input MFP1 Secondary function Audio serial data bus (secondary) bit clock input Audio serial data bus (secondary) word clock input Digital Microphone Input Clock Input General Purpose Input 9 – DOUT O Primary Audio serial data bus data output MFP2 Secondary General purpose output Clock output INT1 output INT2 output Audio serial data bus (secondary) bit clock output Audio serial data bus (secondary) word clock output 10 – IOVdd PWR Supply for IO buffers. 1.1V to 3.6V 11 – IOVss GND Ground for IO buffers. 12 – SCLK I Primary (SPI_Select = 1) SPI serial clock MFP3 Secondary: (SPI_Select = 0) Digital microphone input Audio serial data bus (secondary) bit clock input Audio serial data bus (secondary) DAC/common word clock input Audio serial data bus (secondary) ADC word clock input Audio serial data bus (secondary) data input General purpose input I I2C interface serial clock (SPI_Select = 0) SPI interface mode chip-select signal (SPI_Select = 1) SDA MOSI I/O I2C interface mode serial data input (SPI_Select = 0) SPI interface mode serial data input (SPI_Select = 1) MISO O Primary (SPI_Select = 1) 13 – SCL SS 14 – 15 – Serial data output MFP4 Secondary (SPI_Select = 0) General purpose output CLKOUT output INT1 output INT2 output Audio serial data bus (primary) ADC word clock output Digital microphone clock output Audio serial data bus (secondary) data output Audio serial data bus (secondary) bit clock output Audio serial data bus (secondary) word clock output 4 16 – SPI_SELECT I Control mode select pin ( 1 = SPI, 0 = I2C ) 17 – IN1_L I Multifunction analog input, Single-ended configuration: MIC 1 or Line 1 left Differential configuration: MIC or Line right, negative Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Table 1. TERMINAL FUNCTIONS (continued) 5x5mm 40-PIN QFN (RSB) PIN NO. – NAME TYPE 18 – IN1_R I Multifunction analog input, Single-ended configuration: MIC 1 or Line 1 right Differential configuration: MIC or Line right, positive 19 – IN2_L I Multifunction analog input, Single-ended configuration: MIC 2 or Line 2 right Differential configuration: MIC or Line left, positive 20 – IN2_R I Multifunction analog input, Single-ended configuration: MIC 2 or Line 2 right Differential configuration: MIC or Line left, negative 21 – AVss GND 22 – REF O Reference voltage output for filtering 23 – MICBIAS O Microphone bias voltage output 24 – IN3_L I Multifunction analog input, Single-ended configuration: MIC3 or Line 3 left, Differential configuration: MIC or Line left, positive, Differential configuration: MIC or Line right, negative 25 – IN3_R I Multifunction analog input, Single-ended configuration: MIC3 or Line 3 right, Differential configuration: MIC or Line left, negative, Differential configuration: MIC or Line right, positive 26 – LOL O Left line output 27 – LOR O Right line output 28 – GND_SENSE I External ground reference for headphone interface –0.5V to 0.5V 29, 30 –– AVdd PWR 31 – HPL O 32 – DRVdd_HP 33 – HPR O Right headphone output 34 – MICDET I Microphone detection 35 – VNEG PWR Negative supply for headphones. –1.8V to 0V Input when charge pump is disabled, Filtering output when charge pump is enabled 36 – FLY_N PWR Negative terminal for charge-pump flying capacitor 37 – DVss_CP GND Charge pump ground 38 – FLY_P PWR Positive terminal for charge pump flying capacitor 39 – DVdd_CP PWR Charge Pump supply; recommended to connect to DVdd 40 – DVdd PWR Digital voltage supply 1.26V – 1.95V (2) DESCRIPTION Analog Ground Analog voltage supply 1.5V–1.95V (2) Left headphone output PWR Power supply for headphone output stage Ground-centered circuit configuration, 1.5V to 1.95V Unipolar circuit configuration, 1.5V to 3.6V The AVdd pins are not connected within the device: Must be connected on the PC board. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 5 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Electrical Characteristics Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) VALUE UNIT AVdd to AVss –0.3 to 2.2 V DVdd to DVss –0.3 to 2.2 V IOVDD to IOVSS –0.3 to 3.9 V Digital Input voltage IOVSS to IOVDD + 0.3 V Analog input voltage AVSS to AVdd + 0.3 V Operating temperature range –40 to 85 °C Storage temperature range –55 to 150 °C 105 °C (TJ Max – TA)/ qJA W 35 C/W Junction temperature (TJ Max) QFN package (RSB) Power dissipation qJA Thermal impedance (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Recommended Operating Conditions AVdd Power Supply Voltage Range Referenced to AVss (1) MIN NOM MAX UNIT 1.5 1.8 1.95 V IOVDD Referenced to IOVSS (1) DVdd (2) Referenced to DVss (1) 1.26 1.8 1.95 Referenced to DVss (1) 1.26 1.8 1.95 Ground-centered config 1.5 1.8 1.95 Unipolar config 1.5 3.6 Clock divider uses fractional divide (D > 0), P=1, DVdd ≥ 1.65V (Refer to table in SLAA463, Maximum TLV320AIC3206 Clock Frequencies) 10 20 MHz Clock divider uses integer divide (D = 0), P=1, DVdd ≥ 1.65V (Refer to table in SLAA463, Maximum TLV320AIC3206 Clock Frequencies) 0.512 20 MHz MCLK; Master Clock Frequency; DVdd ≥ 1.65V 50 MHz MCLK; Master Clock Frequency; DVdd ≥ 1.26V 25 DVDD_CP Power Supply Voltage Range DRVDD_HP Referenced to AVss (1) PLL Input Frequency MCLK Master Clock Frequency SCL SCL Clock Frequency LOL, LOR Stereo line output load resistance HPL, HPR Stereo headphone output load resistance Headphone output load resistance CLout Digital output load capacitance TOPR Operating Temperature Range (1) (2) 6 1.1 3.6 400 V kHz 0.6 10 kΩ Single-ended configuration 14.4 16 Ω Differential configuration 24.4 32 Ω 10 –40 pF 85 °C All grounds on board are tied together; they must not differ in voltage by more than 0.2V max, for any combination of ground signals. At DVdd values lower than 1.65V, the PLL does not function. Please see table in SLAA463, Maximum TLV320AIC3206 Clock Frequencies for details on maximum clock frequencies. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Electrical Characteristics, ADC At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER AUDIO ADC (1) (2) TEST CONDITIONS MIN TYP MAX UNIT (CM = 0.9V) Input signal level (for 0dB output) Single-ended, CM = 0.9V 0.5 VRMS 1kHz sine wave input Single-ended Configuration IN1R to Right ADC and IN1L to Left ADC, Rin = 20K, fs = 48kHz, AOSR = 128, MCLK = 256*fs, PLL Disabled; AGC = OFF, Channel Gain = 0dB, Processing Block = PRB_R1, Power Tune = PTM_R4 Device Setup Inputs ac-shorted to ground SNR Signal-to-noise ratio, A-weighted (1) (2) DR Dynamic range A-weighted (1) THD+ N Total Harmonic Distortion plus Noise (2) 80 93 IN2R, IN3R routed to Right ADC and ac-shorted to ground IN2L, IN3L routed to Left ADC and ac-shorted to ground 93 dB –60dB full-scale, 1-kHz input signal 93 dB –3 dB full-scale, 1-kHz input signal –84 IN2R,IN3R routed to Right ADC IN2L, IN3L routed to Left ADC –3dB full-scale, 1-kHz input signal –84 –70 dB AUDIO ADC (CM=0.75V) Input signal level (for 0dB output) Single-ended, CM=0.75V, AVdd = 1.5V Device Setup 1kHz sine wave input Single-ended Configuration INR, IN2R, IN3R routed to Right ADC INL, IN2L, IN3L routed to Left ADC Rin = 20K, fs = 48kHz, AOSR=128, MCLK = 256* fs, PLL Disabled, AGC = OFF, Channel Gain = 0dB, Processing Block = PRB_R1 Power Tune = PTM_R4 SNR Signal-to-noise ratio, A-weighted Inputs ac-shorted to ground DR Dynamic range A-weighted (1) THD+ N Total Harmonic Distortion plus Noise (1) (2) (1) (2) (2) 0.375 VRMS 90 dB –60dB full-scale, 1-kHz input signal 90 dB –3dB full-scale, 1-kHz input signal –81 dB Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 7 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Electrical Characteristics, ADC (continued) At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT AUDIO ADC (Gain=40dB) Input signal level (for 0dB output) Differential Input, CM=0.9V, Channel Gain=40dB 10 mVRMS Inputs ac-shorted to ground, input referred noise 2.8 mVRMS 0.1 dB Gain Error 1kHz sine wave input Single-ended configuration Rin = 20K fs = 48kHz, AOSR=128, MCLK = 256* fs, PLL Disabled AGC = OFF, Channel Gain=0dB Processing Block = PRB_R1, Power Tune = PTM_R4, CM=0.9V 109 dB Input Channel Separation 1kHz sine wave input at -3dBFS Single-ended configuration IN1L routed to Left ADC IN1R routed to Right ADC, Rin = 20K AGC = OFF, AOSR = 128, Channel Gain=0dB, CM=0.9V 108 dB Input Pin Crosstalk 1kHz sine wave input at –3dBFS on IN2L, IN2L internally not routed. IN1L routed to Left ADC ac-coupled to ground 55 dB 0 dB 47.5 dB –6 dB 41.5 dB Single-Ended, Rin = 40K, PGA gain set to 0dB –12 dB Single-Ended, Rin = 40K, PGA gain set to 47.5dB 35.5 dB 0.5 dB Device Setup ICN Idle-Channel Noise, A-weighted (3) (4) 1kHz sine wave input Differential configuration IN1L and IN1R routed to Right ADC IN2L and IN2R routed to Left ADC Rin =10K, fs =48kHz, AOSR=128 MCLK = 256* fs PLL Disabled AGC = OFF Processing Block = PRB_R1, Power Tune = PTM_R4 AUDIO ADC 1kHz sine wave input at –3dBFS on IN2R, IN2R internally not routed. IN1R routed to Right ADC ac-coupled to ground Single-ended configuration Rin = 20K, AOSR=128 Channel, Gain=0dB, CM=0.9V PSRR 217Hz, 100mVpp signal on AVdd, Single-ended configuration, Rin=20K, Channel Gain=0dB; CM=0.9V Single-Ended, Rin = 10K, PGA gain set to 0dB Single-Ended, Rin = 10K, PGA gain set to 47.5dB ADC programmable gain amplifier gain ADC programmable gain amplifier step size (3) (4) 8 Single-Ended, Rin = 20K, PGA gain set to 0dB Single-Ended, Rin = 20K, PGA gain set to 47.5dB 1-kHz tone Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Electrical Characteristics, Bypass Outputs At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ANALOG BYPASS TO HEADPHONE AMPLIFIER, DIRECT MODE Device Setup Load = 16Ω (single-ended), 50pF; Input and Output CM=0.9V; Headphone Output on DRVdd_HP Supply; IN1L routed to HPL and IN1R routed to HPR; Channel Gain=0dB Gain Error THD 0.8 dB Noise, A-weighted (1) Idle Channel, IN1L and IN1R ac-shorted to ground 3.3 mVRMS Total Harmonic Distortion 446mVrms, 1-kHz input signal –81 dB 0.8 dB 6.7 mVRMS 3 mVRMS ANALOG BYPASS TO LINE-OUT AMPLIFIER, PGA MODE Device Setup Load = 10KOhm (single-ended), 50pF; Input and Output CM=0.9V; LINE Output on DRVdd_HP Supply; IN1L, IN1R routed to line out Channel Gain = 0dB Gain Error Gain Error Idle Channel, IN1L and IN1R ac-shorted to ground Noise, A-weighted (1) (1) Channel Gain=40dB, Input Signal (0dB) = 5mVrms Inputs ac-shorted to ground, Input Referred All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 9 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Electrical Characteristics, Microphone Interface At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT MICROPHONE BIAS Bias voltage Bias voltage CM=0.9V, DRVdd_HP = 1.8V Micbias Mode 0, Connect to AVdd or DRVdd_HP Micbias Mode 3, Connect to AVdd 1.5 V AVdd V DRVdd_HP V Micbias Mode 0, Connect to AVdd or DRVdd_HP 1.23 V Micbias Mode 1, Connect to AVdd or DRVdd_HP 1.43 V Micbias Mode 3, Connect to DRVdd_HP CM=0.75V, DRVdd_HP = 1.8V Micbias Mode 3, Connect to AVdd AVdd V DRVdd_HP V Micbias Mode 0, Connect to DRVdd_HP 1.5 V Micbias Mode 1, Connect to DRVdd_HP 1.7 V Micbias Mode 2, Connect to DRVdd_HP 2.5 V Micbias Mode 3, Connect to DRVdd_HP DRVdd_HP V Micbias Mode 0, Connect to DRVdd_HP 1.23 V Micbias Mode 1, Connect to DRVdd_HP 1.43 V Micbias Mode 2, Connect to DRVdd_HP 2.1 V Micbias Mode 3, Connect to DRVdd_HP DRVdd_HP V Micbias Mode 3, Connect to DRVdd_HP MICROPHONE BIAS Bias voltage Bias voltage CM=0.9V, DRVdd_HP = 3.3V CM=0.75V, DRVdd_HP = 3.3V Output Noise Current Sourcing Inline Resistance 10 CM=0.9V, Micbias Mode 2, A-weighted, 20Hz to 20kHz bandwidth, Current load = 0mA. Micbias Mode 2, Connect to DRVdd_HP Micbias Mode 3, Connect to AVdd Micbias Mode 3, Connect to DRVdd_HP Submit Documentation Feedback 9.5 mVRMS 3 131 89 mA Ω Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Electrical Characteristics, Audio DAC Outputs At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0.5 VRMS 87 100 dB –60dB 1kHz input full-scale signal, Word length=20 bits 100 dB AUDIO DAC – STEREO SINGLE-ENDED LINE OUTPUT (CM=0.9V) Load = 10 kΩ (single-ended), 56pF Line Output on AVdd Supply Input & Output CM=0.9V DOSR = 128, MCLK=256* fs, Channel Gain = 0dB, word length = 16 bits, Processing Block = PRB_P1, Power Tune = PTM_P3 Device Setup Full scale output voltage (0dB) SNR Signal-to-noise ratio A-weighted (1) (2) DR Dynamic range, A-weighted THD+N Total Harmonic Distortion plus Noise –3dB full-scale, 1-kHz input signal –81 DAC Gain Error 0 dB, 1kHz input full scale signal 0.5 dB DAC Mute Attenuation Mute 121 dB DAC channel separation –1 dB, 1kHz signal, between left and right HP out 108 dB 100mVpp, 1kHz signal applied to AVdd 72 dB 100mVpp, 217Hz signal applied to AVdd 80 dB (1) (2) DAC PSRR All zeros fed to DAC input –70 dB AUDIO DAC – STEREO SINGLE-ENDED LINE OUTPUT (CM=0.75V) Load = 10 kΩ (single-ended), 56pF Line Output on AVdd Supply Input & Output CM=0.75V; AVdd=1.5V DOSR = 128 MCLK=256* fs Channel Gain = 0dB word length = 20-bits Processing Block = PRB_P1 Power Tune = PTM_P4 Device Setup Full scale output voltage (0dB) 0.375 (1) (2) SNR Signal-to-noise ratio, A-weighted DR Dynamic range, A-weighted THD+N Total Harmonic Distortion plus Noise (1) (2) VRMS All zeros fed to DAC input 99 dB –60dB 1 kHz input full-scale signal 98 dB –1 dB full-scale, 1-kHz input signal –77 dB AUDIO DAC – STEREO SINGLE-ENDED HEADPHONE OUTPUT (GROUND-CENTERED CIRCUIT CONFIGURATION) Load = 16Ω (single-ended), 56pF Input CM=0.9V, Output CM=0V DOSR = 128, MCLK=256* fs, Channel Gain=0dB word length = 16 bits; Processing Block = PRB_P1 Power Tune = PTM_P3 Device Setup FS1 Full scale output voltage (for THD ≤ –40dB) SNR Signal-to-noise ratio, A-weighted (1) DR Dynamic range, A-weighted THD+N Total Harmonic Distortion plus Noise (1) (2) 0.65 (2) (1) (2) All zeros fed to DAC input 85 VRMS 95 dB –60dB 1kHz input full-scale signal, Word Length = 20 bits, Power Tune = PTM_P4 93 dB 500mVRMS output (corresponds to FS1 – 2.3dB), 1-kHz input signal –70 –55 dB Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 11 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Electrical Characteristics, Audio DAC Outputs (continued) At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DAC Gain Error 500mVRMS output, 1kHz input full scale signal 0.5 dB DAC Mute Attenuation Mute 118 dB DAC channel separation –3dB, 1kHz signal, between left and right HP out 102 dB 100mVpp, 1kHz signal applied to AVdd 66 dB 100mVpp, 217Hz signal applied to AVdd 77 dB mW DAC PSRR Power Delivered THD ≤ –40dB 26.5 FS2 Full scale output voltage (for THD ≤ –40dB) Load = 32Ω 0.85 SNR Signal-to-noise ratio, A-weighted (1) (2) All zeros fed to DAC input, Load = 32Ω THD ≤ –40dB, Load = 32Ω Power Delivered V 96 dB 22.5 mW 0.5 VRMS 100 dB AUDIO DAC – STEREO SINGLE-ENDED HEADPHONE OUTPUT (UNIPOLAR CIRCUIT CONFIGURATION) Load = 16Ω (single-ended), 56pF, Headphone Output on AVdd Supply, Input & Output CM=0.9V DOSR = 128, MCLK=256* fs, Channel Gain = 0dB Processing Block = PRB_P1, Power Tune = PTM_P3 Device Setup Full scale output voltage (0dB) SNR Signal-to-noise ratio, A-weighted (3) (4) (3) (4) DR Dynamic range, A-weighted THD+N Total Harmonic Distortion plus Noise (3) (4) 12 All zeros fed to DAC input 87 -60dB 1 kHz input full-scale signal 100 –3dB full-scale, 1-kHz input signal –83 dB –70 dB Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Electrical Characteristics, Misc. At 25°C, AVdd, DVdd, IOVdd,DVdd_CP, DRVdd_HP = 1.8V, fs (Audio) = 48kHz, Cref = 1µF on REF PIN, PLL and Charge pump disabled unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT REFERENCE Reference Voltage Settings Reference Noise CMMode = 0 (0.9V) 0.9 CMMode = 1 (0.75V) 0.75 CM=0.9V, A-weighted, 20Hz to 20kHz bandwidth, Cref = 1mF V 1.1 Decoupling Capacitor Bias Current mVRMS 1 mF 120 mA <10 mA Shutdown Current Device Setup DVdd is provided externally, no clocks supplied, no digital activity, register values are retained I(total) Sum of all supply currents, all supplies at 1.8V Electrical Characteristics, Logic Levels At 25°C, AVdd, DVdd, IOVDD = 1.8V PARAMETER TEST CONDITIONS MIN LOGIC FAMILY VIH Logic Level VIL TYP MAX UNIT CMOS IIH = 5 mA, IOVDD > 1.6V 0.7 × IOVDD V IIH = 5mA, 1.2V ≤ IOVDD <1.6V 0.9 × IOVDD V IIH = 5mA, IOVDD < 1.2V IOVDD IIL = 5 mA, IOVDD > 1.6V –0.3 V IIL = 5mA, 1.2V ≤ IOVDD <1.6V IIL = 5mA, IOVDD < 1.2V VOH IOH = 2 TTL loads VOL IOL = 2 TTL loads 0.3 × IOVDD V 0.1 × IOVDD V 0 V 0.8 × IOVDD Capacitive Load V 0.1 × IOVDD 10 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 V pF 13 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Interface Timing Typical Timing Characteristics — Audio Data Serial Interface Timing (I2S) All specifications at 25°C, DVdd = 1.8V WCLK td(WS) BCLK td(DO-BCLK) td(DO-WS) DOUT th(DI) tS(DI) DIN I2S/LJF Timing in Master Mode 2 Figure 3. I S/LJF/RJF Timing in Master Mode Table 2. I2S/LJF/RJF Timing in Master Mode (see Figure 3) PARAMETER IOVDD=1.8V MIN IOVDD=3.3V MAX MIN UNITS MAX td(WS) WCLK delay 30 20 ns td (DO-WS) WCLK to DOUT delay (For LJF Mode only) 20 20 ns td (DO-BCLK) BCLK to DOUT delay 22 20 ns ts(DI) DIN setup 8 8 th(DI) DIN hold 8 8 tr Rise time 24 12 ns tf Fall time 24 12 ns 14 Submit Documentation Feedback ns ns Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 WCLK th(WS) tL(BCLK) BCLK tH(BCLK) ts(WS) td(DO-WS) td(DO-BCLK) DOUT th(DI) ts(DI) DIN Figure 4. I2S/LJF/RJF Timing in Slave Mode Table 3. I2S/LJF/RJF Timing in Slave Mode (see Figure 4) PARAMETER IOVDD=1.8V MIN IOVDD=3.3V MAX MIN UNITS MAX tH (BCLK) BCLK high period 35 35 tL (BCLK) BCLK low period 35 35 ns ts (WS) WCLK setup 8 8 th (WS) WCLK hold 8 td (DO-WS) WCLK to DOUT delay (For LJF mode only) td (DO-BCLK) BCLK to DOUT delay ts(DI) DIN setup 8 8 th(DI) DIN hold 8 8 tr Rise time 4 4 tf Fall time 4 4 8 20 20 22 22 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 15 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Typical DSP Timing Characteristics All specifications at 25°C, DVdd = 1.8V WCLK td(WS) td(WS) BCLK td(DO-BCLK) DOUT th(DI) ts(DI) DIN Figure 5. DSP Timing in Master Mode Table 4. DSP Timing in Master Mode (see Figure 5) PARAMETER IOVDD=1.8V MIN IOVDD=3.3V MAX MIN 30 UNITS MAX td (WS) WCLK delay td (DO-BCLK) BCLK to DOUT delay ts(DI) DIN setup 8 8 th(DI) DIN hold 8 8 tr Rise time 24 12 ns tf Fall time 24 12 ns 22 20 ns 20 ns ns ns WCLK th(ws) BCLK ts(ws) th(ws) th(ws) tL(BCLK) tH(BCLK) td(DO-BCLK) DOUT th(DI) ts(DI) DIN Figure 6. DSP Timing in Slave Mode Table 5. DSP Timing in Slave Mode (see Figure 6) PARAMETER IOVDD=1.8V MIN IOVDD=3.3V MAX MIN UNITS MAX tH (BCLK) BCLK high period 35 35 ns tL (BCLK) BCLK low period 35 35 ns ts(WS) WCLK setup 8 8 ns th(WS) WCLK hold 8 8 td (DO-BCLK) BCLK to DOUT delay ts(DI) DIN setup 8 8 th(DI) DIN hold 8 8 tr Rise time 4 4 ns tf Fall time 4 4 ns 16 Submit Documentation Feedback 22 ns 22 ns ns ns Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 I2C Interface Timing Figure 7. I2C Interface Timing Table 6. I2C Interface Timing PARAMETER TEST CONDITION Standard-Mode MIN TYP 0 Fast-Mode MAX 0 TYP UNITS MAX fSCL SCL clock frequency tHD;STA Hold time (repeated) START condition. After this period, the first clock pulse is generated. 4.0 0.8 ms tLOW LOW period of the SCL clock 4.7 1.3 ms tHIGH HIGH period of the SCL clock 4.0 0.6 ms tSU;STA Setup time for a repeated START condition 4.7 0.8 ms tHD;DAT Data hold time: For I2C bus devices tSU;DAT Data set-up time tr SDA and SCL Rise Time tf SDA and SCL Fall Time tSU;STO Set-up time for STOP condition 4.0 0.8 ms tBUF Bus free time between a STOP and START condition 4.7 1.3 ms Cb Capacitive load for each bus line 0 100 MIN 400 3.45 0 1000 20+0.1Cb 300 300 20+0.1Cb 300 250 0.9 100 400 Product Folder Link(s): TLV320AIC3206 ms ns 400 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated kHz ns ns pF 17 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com SPI Interface Timing SS S t t Lead t t Lag td sck SCLK tf t sckl tr t sckh tv MISO t dis MSB OUT BIT 6 . . . 1 LSB OUT ta MOSI t hi t su MSB IN BIT 6 . . . 1 LSB IN Figure 8. SPI Interface Timing Diagram Timing Requirements (See Figure 8) At 25°C, DVdd = 1.8V Table 7. SPI Interface Timing PARAMETER TEST CONDITION IOVDD=1.8V MIN tsck SCLK Period (1) tsckh tsckl IOVDD=3.3V TYP MAX MIN TYP UNITS MAX 100 50 ns SCLK Pulse width High 50 25 ns SCLK Pulse width Low 50 25 ns tlead Enable Lead Time 30 20 ns tlag Enable Lag Time 30 20 ns td Sequential Transfer Delay 40 20 ta Slave DOUT access time 40 20 ns tdis Slave DOUT disable time 40 20 ns tsu DIN data setup time 15 10 thi DIN data hold time 15 10 tv;DOUT DOUT data valid time tr tf (1) 18 ns ns ns 25 18 ns SCLK Rise Time 4 4 ns SCLK Fall Time 4 4 ns These parameters are based on characterization and are not tested in production. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Typical Characteristics Device Power Consumption Device power consumption largely depends on PowerTune configuration. For information on device power consumption, see the TLV320AIC3206 Application Reference Guide, literature number SLAA463. Typical Performance ADC SNR vs CHANNEL GAIN TOTAL HARMONIC DISTORTION GCHP CONFIGURATION vs HEADPHONE OUTPUT POWER 0 100 RIN = 10 kW, Differential -10 RIN = 20 kW, Differential 90 -20 85 -30 80 RIN = 10 kW, Single Ended THDN dB SNR - Signal-to-Noise Ratio - dB 95 75 RIN = 20 kW, Single Ended 70 32W -40 16W -50 65 -60 60 -70 55 -80 50 -20 0 20 Channel Gain - dB 40 60 0 10 20 30 Headphone Output Power mW Figure 9. 50 Figure 10. TOTAL HARMONIC DISTORTION UNIPOLAR CONFIGURATION vs HEADPHONE OUTPUT POWER TOTAL HARMONIC DISTORTION vs HEADPHONE OUTPUT POWER 0 0 32 W BTL Load CM = 1.65 V, RL = 32 W -10 THD - Total Harmonic Distortion - dB CM = 0.9 V, RL = 16 W CM = 0.9 V, RL = 32 W -10 THD - Total Harmonic Distortion - dB 40 -20 -30 CM = 1.65 V, RL = 16 W -40 -50 -60 -70 GCHP Mode DRVDD_HP = 1.8V CM = 0.9 V -20 -30 Unipolar Mode DRVDD_HP = 3.3V CM = 1.65 V -40 -50 -60 -70 -80 -80 -90 -90 0 20 40 60 Headphone Output Power - mW 80 0 Figure 11. 50 100 150 Headphone Output Power - mW 200 Figure 12. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 19 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com HEADPHONE SNR AND OUTPUT POWER vs OUTPUT COMMON MODE SETTING 105 60 50 SNR 95 90 40 85 30 80 Output Power 75 20 Power Delivered - mW SNR - Signal-to-Noise Ratio - dB 100 70 10 65 60 0 0 0.75 0.9 1.25 1.5 Output Common Mode Setting 1.65 Figure 13. FFT DAC PLAYBACK TO HEADPHONE FFT @ -1dBFS (UNIPOLAR MODE) vs FREQUENCY SINGLE ENDED LINE INPUT TO ADC FFT @ -1dBr vs FREQUENCY 0 0 DAC ADC -20 -20 -40 Power - dBr Power - dBFs -40 -60 -80 -100 -60 -80 -100 -120 -120 -140 -160 0 5000 10000 f - Frequency - Hz 15000 20000 -140 0 Figure 14. 20 5000 10000 f - Frequency - Hz 15000 20000 Figure 15. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 DAC PLAYBACK TO HEADPHONE FFT @ -1dBFS (GROUND-CENTERED MODE) vs FREQUENCY DAC PLAYBACK TO LINE-OUT FFT @ -1dBFS vs FREQUENCY 0 0 DAC -20 -20 -40 -40 Power - dBr Power - dBr DAC -60 -80 -60 -80 -100 -100 -120 -120 -140 0 5000 10000 f - Frequency - Hz 15000 20000 -140 0 5000 Figure 16. -20 -20 -40 -40 Power - dBr Power - dBr 0 -60 -80 -60 -80 -100 -100 -120 -120 -140 10000 f - Frequency - Hz 20000 LINE INPUT TO LINE-OUT FFT @ 446mVrms (PGA MODE) vs FREQUENCY 0 5000 15000 Figure 17. LINE INPUT TO HEADPHONE FFT @ 446mVrms (UNIPOLAR MODE) vs FREQUENCY 0 10000 f - Frequency - Hz 15000 20000 -140 0 Figure 18. 5000 10000 f - Frequency - Hz 15000 20000 Figure 19. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 21 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Typical Circuit Configuration Host Processor Reset MCLK SCL SDA BCLK WCLK DIN DOUT 0.1u 1K SPI_Select 1k 1k LOL 2.7k 4700p MICBIAS 1K 0.1u 4700p 0.1u TPA 2012 Class D Amp LOR 0.1uF IN1_R TLV320AIC3206 0.1uF IN1_L MFP3/SCLK MFP4/MISO 1.1...3.6V MFP5/GPIO 0.1uF IOVDD IN2_L AVDD 0.1uF 1.8...1.95V AVDD IN2_R 1k 0.1u DVDD 1k DVDD_CP MICDET 10 uF DRVDD_HP 0.1uF FLY_P IN3_R IN3_L 2.2 uF X7R FLY _N GND_Sense Headset_Mic Earjack microphone and headset speakers HPR HPL REF AVSS IOVSS DVSS_ CP DVSS DVSS VNEG Headset_Spkr_R 2.2 uF X7R Headset_Spkr_L Headset_Gnd 1uF Figure 20. Typical Circuit Configuration APPLICATION OVERVIEW The TLV320AIC3206 offers a wide range of configuration options. Figure 1 shows the basic functional blocks of the device. space Device Connections Digital Pins Only a small number of digital pins are dedicated to a single function; whenever possible, the digital pins have a default function, and also can be reprogrammed to cover alternative functions for various applications. The fixed-function pins are Reset and the SPI_Select pin, which are HW control pins. Depending on the state of SPI_Select, the two control-bus pins SCL/SS and SDA/MOSI are configured for either I2C or SPI protocol. Other digital IO pins can be configured for various functions via register control. An overview of available functionality is given in Multifunction Pins. Analog Pins Analog functions can also be configured to a large degree. For minimum power consumption, analog blocks are powered down by default. The blocks can be powered up with fine granularity according to the application needs. Multifunction Pins Table 8 shows the possible allocation of pins for specific functions. The PLL input, for example, can be programmed to be any of 4 pins (MCLK, BCLK, DIN, GPIO). 22 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Table 8. Multifunction Pin Assignments Pin Function A 1 2 3 4 5 6 7 8 MCLK BCLK WCLK DIN MFP1 DOUT MFP2 DMDIN/ MFP3/ SCLK DMCLK/ MFP4/ MISO GPIO MFP5 S (1) S (2) PLL Input B Codec Clock Input C ,D (4) S S ,D 2 E (5) I S BCLK output 2 E I S WCLK input F I2S WCLK output G I2S ADC word clock input S (3) E (2) 2 I S BCLK input D S (1) S (3) (2) E, D E E 2 E H I S ADC WCLK out I I2S DIN E E J I2S DOUT K General Purpose Output I K General Purpose Output II K General Purpose Output III L General Purpose Input I L General Purpose Input II L General Purpose Input III M INT1 output E N INT2 output E Q Secondary I2S BCLK input E E R Secondary I2S WCLK in E E S 2 Secondary I S DIN E T Secondary I2S DOUT U Secondary I2S BCLK OUT E, D E, D E E E E E E E E E E E E 2 E E E V Secondary I S WCLK OUT E E E X Aux Clock Output E E E (1) (2) (3) (4) (5) S(1): S(2): (3) The MCLK pin can be used to drive the PLL and Codec Clock inputs simultaneously The BCLK pin can be used to drive the PLL and Codec Clock and audio interface bit clock inputs simultaneously S : The GPIO/MFP5 pin can be used to drive the PLL and Codec Clock inputs simultaneously D: Default Function E: The pin is exclusively used for this function, no other function can be implemented with the same pin (e.g. if GPIO/MFP5 has been allocated for General Purpose Output, it cannot be used as the INT1 output at the same time) Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 23 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Analog Audio I/O The analog I/O path of the TLV320AIC3206 features a large set of options for signal conditioning as well as signal routing: • 6 analog inputs which can be mixed and/or multiplexed in single-ended and/or differential configuration • 2 programmable gain amplifiers (PGA) with a range of 0 to +47.5dB • 2 mixer amplifiers for analog bypass • 2 low power analog bypass channels • Mute function • Channel-to-channel phase adjustment • Fast charge of ac-coupling capacitors • Anti thump Analog Low Power Bypass The TLV320AIC3206 offers two analog-bypass modes. In either of the modes, an analog input signal can be routed from an analog input pin to an amplifier driving an analog output pin. Neither the ADC nor the DAC resources are required for such operation; this supports low-power operation during analog-bypass mode. In analog low-power bypass mode, line-level signals can be routed directly from the analog inputs IN1_L to the left headphone amplifier (HPL) and IN1_R to HPR. ADC Bypass Using Mixer Amplifiers In addition to the low-power bypass mode, there is a bypass mode that uses the programmable gain amplifiers of the input stage in conjunction with a mixer amplifier. With this mode, microphone-level signals can be amplified and routed to the line or headphone outputs, fully bypassing the ADC and DAC. To enable this mode, the mixer amplifiers are powered on via software command. Headphone Output The stereo headphone drivers on pins HPL and HPR can drive loads with impedances down to 16Ω in single-ended DC-coupled headphone configurations. An integral charge pump generates the negative supply required to operate the headphone drivers in dc-coupled mode, where the common mode of the output signal is made equal to the ground of the headphone load using a ground-sense circuit. Operation of headphone drivers in dc-coupled (ground centered mode) eliminates the need for large dc-blocking capacitors. HPL HPR GND_SENSE Figure 21. TLV320AIC3206 Ground-Centered Headphone Output Alternatively the headphone amplifier can also be operated in a unipolar circuit configuration using DC blocking capacitors. 24 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Line Outputs Line Out Amplifier Overview The stereo line level drivers on LOL and LOR pins can drive a wide range of line level resistive impedances in the range of 600Ω to 10kΩ. The output common modes of line level drivers can be configured to equal either the analog input common-mode setting, or 1.65V. With output common-mode setting of 1.65V and DRVdd_HP supply at 3.3V the line-level drivers can drive up to 1Vrms output signal. The line-level drivers can drive out a mixed combination of DAC signal and attenuated ADC PGA signal. Signal mixing is register-programmable. ADC The TLV320AIC3206 includes a stereo audio ADC, which uses a delta-sigma modulator with a programmable oversampling ratio, followed by a digital decimation filter. The ADC supports sampling rates from 8kHz to 192kHz. In order to provide optimal system power management, the stereo recording path can be powered up one channel at a time, to support the case where only mono record capability is required. The ADC path of the TLV320AIC3206 features a large set of options for signal conditioning as well as signal routing: • 2 ADCs • 6 analog inputs which can be mixed and/or multiplexed in single-ended and/or differential configuration • 2 programmable gain amplifiers (PGA) with a range of 0 to +47.5dB • 2 mixer amplifiers for analog bypass • 2 low power analog bypass channels • Fine gain adjust of digital channels with 0.1 dB step size • Digital volume control with a range of -12 to +20dB • Mute function In • • • • addition to the standard set of ADC features the TLV320AIC3206 also offers the following special functions: Channel-to-channel phase adjustment Fast charge of ac-coupling capacitors Anti thump Adaptive filter mode ADC Processing The TLV320AIC3206 ADC channel includes a built-in digital decimation filter to process the oversampled data from the to generate digital data at Nyquist sampling rate with high dynamic range. The decimation filter can be chosen from three different types, depending on the required frequency response, group delay and sampling rate. ADC Processing Blocks The TLV320AIC3206 offers a range of processing blocks which implement various signal processing capabilities along with decimation filtering. These processing blocks give users the choice of how much and what type of signal processing they may use and which decimation filter is applied. The choice between these processing blocks is part of the PowerTune strategy to balance power conservation and signal-processing flexibility. Less signal-processing capability reduces the power consumed by the device. Table 9 gives an overview of the available processing blocks of the ADC channel and their properties. The Resource Class Column (RC) gives an approximate indication of power consumption. The signal processing blocks available are: • First-order IIR • Scalable number of biquad filters • Variable-tap FIR filter Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 25 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com The processing blocks are tuned for common cases and can achieve high anti-alias filtering or low-group delay in combination with various signal processing effects such as audio effects and frequency shaping. The available first order IIR, BiQuad and FIR filters have fully user-programmable coefficients. The Resource Class Column (RC) gives an approximate indication of power consumption. Table 9. ADC Processing Blocks Processing Blocks Channel Decimation Filter 1st Order IIR Available Number BiQuads FIR Required AOSR Value Resource Class PRB_R1 (1) Stereo A Yes 0 No 128,64 6 PRB_R2 Stereo A Yes 5 No 128,64 8 PRB_R3 Stereo A Yes 0 25-Tap 128,64 8 PRB_R4 Right A Yes 0 No 128,64 3 PRB_R5 Right A Yes 5 No 128,64 4 PRB_R6 Right A Yes 0 25-Tap 128,64 4 PRB_R7 Stereo B Yes 0 No 64 3 PRB_R8 Stereo B Yes 3 No 64 4 (1) PRB_R9 Stereo B Yes 0 20-Tap 64 4 PRB_R10 Right B Yes 0 No 64 2 PRB_R11 Right B Yes 3 No 64 2 PRB_R12 Right B Yes 0 20-Tap 64 2 PRB_R13 Stereo C Yes 0 No 32 3 PRB_R14 Stereo C Yes 5 No 32 4 PRB_R15 Stereo C Yes 0 25-Tap 32 4 PRB_R16 Right C Yes 0 No 32 2 PRB_R17 Right C Yes 5 No 32 2 PRB_R18 Right C Yes 0 25-Tap 32 2 Default For more detailed information see the Application Reference Guide, SLAU306 26 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 DAC The TLV320AIC3206 includes a stereo audio DAC supporting data rates from 8kHz to 192kHz. Each channel of the stereo audio DAC consists of a signal-processing engine with fixed processing blocks, a digital interpolation filter, multi-bit digital delta-sigma modulator, and an analog reconstruction filter. The DAC is designed to provide enhanced performance at low sampling rates through increased oversampling and image filtering, thereby keeping quantization noise generated within the delta-sigma modulator and signal images strongly suppressed within the audio band to beyond 20kHz. To handle multiple input rates and optimize power dissipation and performance, the TLV320AIC3206 allows the system designer to program the oversampling rates over a wide range from 1 to 1024. The system designer can choose higher oversampling ratios for lower input data rates and lower oversampling ratios for higher input data rates. The TLV320AIC3206 DAC channel includes a built-in digital interpolation filter to generate oversampled data for the sigma-delta modulator. The interpolation filter can be chosen from three different types depending on required frequency response, group delay and sampling rate. The DAC path of the TLV320AIC3206 features many options for signal conditioning and signal routing: • 2 headphone amplifiers – Ground-centered, bipolar operation or unipolar operation – Usable in single-ended or differential mode – Analog volume setting with a range of -6 to +14 dB • 2 line-out amplifiers – Usable in single-ended or differential mode – Analog volume setting with a range of -6 to +29 dB • Digital volume control with a range of -63.5 to +24dB • Mute function • Dynamic range compression (DRC) In • • • addition to the standard set of DAC features the TLV320AIC3206 also offers the following special features: Built in sine wave generation (beep generator) Digital auto mute Adaptive filter mode DAC Processing Blocks — Overview The TLV320AIC3206 implements signal processing capabilities and interpolation filtering via processing blocks. These fixed processing blocks give users the choice of how much and what type of signal processing they may use and which interpolation filter is applied. The choice between these processing blocks is part of the PowerTune strategy balancing power conservation and signal processing flexibility. Less signal processing capability will result in less power consumed by the device. Table 10 gives an overview over all available processing blocks of the DAC channel and their properties. The Resource Class Column (RC) gives an approximate indication of power consumption. The signal processing blocks available are: • First-order IIR • Scalable number of biquad filters • 3D – Effect • Beep Generator The processing blocks are tuned for typical cases and can achieve high image rejection or low group delay in combination with various signal processing effects such as audio effects and frequency shaping. The available first-order IIR and biquad filters have fully user-programmable coefficients. The Resource Class Column (RC) gives an approximate indication of power consumption. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 27 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Table 10. Overview – DAC Predefined Processing Blocks (1) Processing Block No. Interpolation Filter Channel 1st Order IIR Available Num. of Biquads DRC 3D Beep Generator Resource Class PRB_P1 (1) A Stereo No 3 No No No 8 PRB_P2 A Stereo Yes 6 Yes No No 12 PRB_P3 A Stereo Yes 6 No No No 10 PRB_P4 A Left No 3 No No No 4 PRB_P5 A Left Yes 6 Yes No No 6 PRB_P6 A Left Yes 6 No No No 6 PRB_P7 B Stereo Yes 0 No No No 6 PRB_P8 B Stereo No 4 Yes No No 8 PRB_P9 B Stereo No 4 No No No 8 PRB_P10 B Stereo Yes 6 Yes No No 10 PRB_P11 B Stereo Yes 6 No No No 8 PRB_P12 B Left Yes 0 No No No 3 PRB_P13 B Left No 4 Yes No No 4 PRB_P14 B Left No 4 No No No 4 PRB_P15 B Left Yes 6 Yes No No 6 PRB_P16 B Left Yes 6 No No No 4 PRB_P17 C Stereo Yes 0 No No No 3 PRB_P18 C Stereo Yes 4 Yes No No 6 PRB_P19 C Stereo Yes 4 No No No 4 PRB_P20 C Left Yes 0 No No No 2 PRB_P21 C Left Yes 4 Yes No No 3 PRB_P22 C Left Yes 4 No No No 2 PRB_P23 A Stereo No 2 No Yes No 8 PRB_P24 A Stereo Yes 5 Yes Yes No 12 PRB_P25 A Stereo Yes 5 Yes Yes Yes 12 Default For more detailed information see the Application Reference Guide, SLAU306 Digital Audio I/O Interface Audio data is transferred between the host processor and the TLV320AIC3206 via the digital audio data serial interface, or audio bus. The audio bus on this device is very flexible, including left or right-justified data options, support for I2S or PCM protocols, programmable data length options, a TDM mode for multichannel operation, very flexible master/slave configurability for each bus clock line, and the ability to communicate with multiple devices within a system directly. The audio bus of the TLV320AIC3206 can be configured for left or right-justified, I2S, DSP, or TDM modes of operation, where communication with standard PCM interfaces is supported within the TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits by configuring Page 0, Register 27, D(5:4). In addition, the word clock and bit clock can be independently configured in either Master or Slave mode, for flexible connectivity to a wide variety of processors. The word clock is used to define the beginning of a frame, and may be programmed as either a pulse or a square-wave signal. The frequency of this clock corresponds to the maximum of the selected ADC and DAC sampling frequencies. The bit clock is used to clock in and clock out the digital audio data across the serial bus. When in Master mode, this signal can be programmed to generate variable clock pulses by controlling the bit-clock divider in Page 0, Register 30. The number of bit-clock pulses in a frame may need adjustment to accommodate various word-lengths as well as to support the case when multiple TLV320AIC3206s may share the same audio bus. 28 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 The TLV320AIC3206 also includes a feature to offset the position of start of data transfer with respect to the word-clock. This offset can be controlled in terms of number of bit-clocks and can be programmed in Page 0, Register 28. The TLV320AIC3206 also has the feature of inverting the polarity of the bit-clock used for transferring the audio data as compared to the default clock polarity used. This feature can be used independently of the mode of audio interface chosen. This can be configured via Page 0, Register 29, D(3). The TLV320AIC3206 further includes programmability (Page 0, Register 27, D0) to place the DOUT line into a hi-Z (3-state) condition during all bit clocks when valid data is not being sent. By combining this capability with the ability to program at what bit clock in a frame the audio data begins, time-division multiplexing (TDM) can be accomplished, enabling the use of multiple codecs on a single audio serial data bus. When the audio serial data bus is powered down while configured in master mode, the pins associated with the interface are put into a hi-Z output condition. By default when the word-clocks and bit-clocks are generated by the TLV320AIC3206, these clocks are active only when the codec (ADC, DAC or both) are powered up within the device. This is done to save power. However, it also supports a feature when both the word clocks and bit-clocks can be active even when the codec in the device is powered down. This is useful when using the TDM mode with multiple codecs on the same bus, or when word-clock or bit-clocks are used in the system as general-purpose clocks. Clock Generation and PLL The TLV320AIC3206 supports a wide range of options for generating clocks for the ADC and DAC sections as well as interface and other control blocks. The clocks for ADC and DAC require a source reference clock. This clock can be provided on variety of device pins such as MCLK, BCLK or GPI pins. The CODEC_CLKIN can then be routed through highly-flexible clock dividers to generate the various clocks required for the ADC and DAC sections. In the event that the desired audio clocks cannot be generated from the reference clocks on MCLK, BCLK or GPIO, the TLV320AIC3206 also provides the option of using the on-chip PLL which supports a wide range of fractional multiplication values to generate the required clocks. Starting from CODEC_CLKIN the TLV320AIC3206 provides several programmable clock dividers to help achieve a variety of sampling rates for ADC, DAC and clocks for the processing block. To minimize power consumption, the system ideally provides a master clock that is a suitable integer multiple of the desired sampling frequencies. In such cases, internal dividers can be programmed to set up the required internal clock signals at very low power consumption. For cases where such master clocks are not available, the built-in PLL can be used to generate a clock signal that serves as an internal master clock. In fact, this master clock can also be routed to an output pin and may be used elsewhere in the system. The clock system is flexible enough that it even allows the internal clocks to be derived directly from an external clock source, while the PLL is used to generate some other clock that is only used outside the TLV320AIC3206. For more detailed information see the Application Reference Guide, SLAU306 Control Interfaces The TLV320AIC3206 control interface supports SPI or I2C communication protocols, with the protocol selectable using the SPI_SELECT pin. For SPI, SPI_SELECT should be tied high; for I2C, SPI_SELECT should be tied low. It is not recommended to change the state of SPI_SELECT during device operation. I2C Control The TLV320AIC3206 supports the I2C control protocol, and will respond to the I2C address of 0011000. I2C is a two-wire, open-drain interface supporting multiple devices and masters on a single bus. Devices on the I2C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines HIGH. Instead, the bus wires are pulled HIGH by pullup resistors, so the bus wires are HIGH when no device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus simultaneously, there is no driver contention. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 29 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com SPI Control In the SPI control mode, the TLV320AIC3206 uses the pins SCL/SS as SS, SCLK as SCLK, MISO as MISO, SDA/MOSI as MOSI; a standard SPI port with clock polarity setting of 0 (typical microprocessor SPI control bit CPOL = 0). The SPI port allows full-duplex, synchronous, serial communication between a host processor (the master) and peripheral devices (slaves). The SPI master (in this case, the host processor) generates the synchronizing clock (driven onto SCLK) and initiates transmissions. The SPI slave devices (such as the TLV320AIC3206) depend on a master to start and synchronize transmissions. A transmission begins when initiated by an SPI master. The byte from the SPI master begins shifting in on the slave MOSI pin under the control of the master serial clock (driven onto SCLK). As the byte shifts in on the MOSI pin, a byte shifts out on the MISO pin to the master shift register. For more detailed information see the Application Reference Guide, SLAU306 Power Supply The device has an integrated charge pump. Using the device in ground-centered headphone configuration, it can be conveniently supplied from a single 1.5V to 1.95V rail. It has separate power domains for digital IO, digital core, analog core, charge-pump input and headphone drive, all of which can be connected together and be supplied from one source. For improved power efficiency, the digital core voltage can range from 1.26V to 1.95V. The IO voltage can be supplied in the range of 1.1V to 3.6V. For more detailed information see the TLV320AIC3206Application Reference Guide, SLAU306 Device Special Functions The following special functions are available to support advanced system requirements: • Headset detection • Interrupt generation • Flexible pin multiplexing For more detailed information see the Application Reference Guide, SLAU306 Register Map Summary Table 11. Summary of Register Map Decimal Hex DESCRIPTION PAGE NO. REG. NO. PAGE NO. REG. NO. 0 0 0x00 0x00 Page Select Register 0 1 0x00 0x01 Software Reset Register 0 2 0x00 0x02 Reserved Register 0 3 0x00 0x03 Reserved Register 0 4 0x00 0x04 Clock Setting Register 1, Multiplexers 0 5 0x00 0x05 Clock Setting Register 2, PLL P&R Values 0 6 0x00 0x06 Clock Setting Register 3, PLL J Values 0 7 0x00 0x07 Clock Setting Register 4, PLL D Values (MSB) 0 8 0x00 0x08 Clock Setting Register 5, PLL D Values (LSB) 0 9-10 0x00 0x09-0x0A Reserved Register 0 11 0x00 0x0B Clock Setting Register 6, NDAC Values 0 12 0x00 0x0C Clock Setting Register 7, MDAC Values 0 13 0x00 0x0D DAC OSR Setting Register 1, MSB Value 0 14 0x00 0x0E DAC OSR Setting Register 2, LSB Value 0 15 0x00 0x0F Reserved Register 0 16 0x00 0x10 Reserved Register 0 17 0x00 0x11 Reserved Register 30 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Table 11. Summary of Register Map (continued) Decimal Hex DESCRIPTION PAGE NO. REG. NO. PAGE NO. REG. NO. 0 18 0x00 0x12 Clock Setting Register 8, NADC Values 0 19 0x00 0x13 Clock Setting Register 9, MADC Values 0 20 0x00 0x14 ADC Oversampling (AOSR) Register 0 21 0x00 0x15 Reserved Register 0 22 0x00 0x16 Reserved Register 0 23 0x00 0x17 Reserved Register 0 24 0x00 0x18 Reserved Register 0 25 0x00 0x19 Clock Setting Register 10, Multiplexers 0 26 0x00 0x1A Clock Setting Register 11, CLKOUT M divider value 0 27 0x00 0x1B Audio Interface Setting Register 1 0 28 0x00 0x1C Audio Interface Setting Register 2, Data offset setting 0 29 0x00 0x1D Audio Interface Setting Register 3 0 30 0x00 0x1E Clock Setting Register 12, BCLK N Divider 0 31 0x00 0x1F Audio Interface Setting Register 4, Secondary Audio Interface 0 32 0x00 0x20 Audio Interface Setting Register 5 0 33 0x00 0x21 Audio Interface Setting Register 6 0 34 0x00 0x22 Digital Interface Misc. Setting Register 0 35 0x00 0x23 Reserved Register 0 36 0x00 0x24 ADC Flag Register 0 37 0x00 0x25 DAC Flag Register 1 0 38 0x00 0x26 DAC Flag Register 2 0 39-41 0x00 0x27-0x29 Reserved Register 0 42 0x00 0x2A Sticky Flag Register 1 0 43 0x00 0x2B Interrupt Flag Register 1 0 44 0x00 0x2C Sticky Flag Register 2 0 45 0x00 0x2D Sticky Flag Register 3 0 46 0x00 0x2E Interrupt Flag Register 2 0 47 0x00 0x2F Interrupt Flag Register 3 0 48 0x00 0x30 INT1 Interrupt Control Register 0 49 0x00 0x31 INT2 Interrupt Control Register 0 50-51 0x00 0x32-0x33 Reserved Register 0 52 0x00 0x34 GPIO/MFP5 Control Register 0 53 0x00 0x35 DOUT/MFP2 Function Control Register 0 54 0x00 0x36 DIN/MFP1 Function Control Register 0 55 0x00 0x37 MISO/MFP4 Function Control Register 0 56 0x00 0x38 SCLK/MFP3 Function Control Register 0 57-59 0x00 0x39-0x3B Reserved Registers 0 60 0x00 0x3C DAC Signal Processing Block Control Register 0 61 0x00 0x3D ADC Signal Processing Block Control Register 0 62 0x00 0x3E Reserved Register 0 63 0x00 0x3F DAC Channel Setup Register 1 0 64 0x00 0x40 DAC Channel Setup Register 2 0 65 0x00 0x41 Left DAC Channel Digital Volume Control Register 0 66 0x00 0x42 Right DAC Channel Digital Volume Control Register 0 67 0x00 0x43 Headset Detection Configuration Register 0 68 0x00 0x44 DRC Control Register 1 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 31 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Table 11. Summary of Register Map (continued) Decimal Hex DESCRIPTION PAGE NO. REG. NO. PAGE NO. REG. NO. 0 69 0x00 0x45 DRC Control Register 2 0 70 0x00 0x46 DRC Control Register 3 0 71 0x00 0x47 Beep Generator Register 1 0 72 0x00 0x48 Beep Generator Register 2 0 73 0x00 0x49 Beep Generator Register 3 0 74 0x00 0x4A Beep Generator Register 4 0 75 0x00 0x4B Beep Generator Register 5 0 76 0x00 0x4C Beep Generator Register 6 0 77 0x00 0x4D Beep Generator Register 7 0 78 0x00 0x4E Beep Generator Register 8 0 79 0x00 0x4F Beep Generator Register 9 0 80 0x00 0x50 Reserved Register 0 81 0x00 0x51 ADC Channel Setup Register 0 82 0x00 0x52 ADC Fine Gain Adjust Register 0 83 0x00 0x53 Left ADC Channel Volume Control Register 0 84 0x00 0x54 Right ADC Channel Volume Control Register 0 85 0x00 0x55 ADC Phase Adjust Register 0 86 0x00 0x56 Left Channel AGC Control Register 1 0 87 0x00 0x57 Left Channel AGC Control Register 2 0 88 0x00 0x58 Left Channel AGC Control Register 3 0 89 0x00 0x59 Left Channel AGC Control Register 4 0 90 0x00 0x5A Left Channel AGC Control Register 5 0 91 0x00 0x5B Left Channel AGC Control Register 6 0 92 0x00 0x5C Left Channel AGC Control Register 7 0 93 0x00 0x5D Left Channel AGC Control Register 8 0 94 0x00 0x5E Right Channel AGC Control Register 1 0 95 0x00 0x5F Right Channel AGC Control Register 2 0 96 0x00 0x60 Right Channel AGC Control Register 3 0 97 0x00 0x61 Right Channel AGC Control Register 4 0 98 0x00 0x62 Right Channel AGC Control Register 5 0 99 0x00 0x63 Right Channel AGC Control Register 6 0 100 0x00 0x64 Right Channel AGC Control Register 7 0 101 0x00 0x65 Right Channel AGC Control Register 8 0 102 0x00 0x66 DC Measurement Register 1 0 103 0x00 0x67 DC Measurement Register 2 0 104 0x00 0x68 Left Channel DC Measurement Output Register 1 0 105 0x00 0x69 Left Channel DC Measurement Output Register 2 0 106 0x00 0x6A Left Channel DC Measurement Output Register 3 0 107 0x00 0x6B Right Channel DC Measurement Output Register 1 0 108 0x00 0x6C Right Channel DC Measurement Output Register 2 0 109 0x00 0x6D Right Channel DC Measurement Output Register 3 0 110-127 0x00 0x6E-0x7F Reserved Register 1 0 0x01 0x00 Page Select Register 1 1 0x01 0x01 Power Configuration Register 1 1 2 0x01 0x02 Power Configuration Register 2 1 3 0x01 0x03 Playback Configuration Register 1 32 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 Table 11. Summary of Register Map (continued) Decimal Hex DESCRIPTION PAGE NO. REG. NO. PAGE NO. REG. NO. 1 4 0x01 0x04 Playback Configuration Register 2 1 5-8 0x01 0x05-0x08 Reserved Register 1 9 0x01 0x09 Output Driver Power Control Register 1 10 0x01 0x0A Common Mode Control Register 1 11 0x01 0x0B Over Current Protection Configuration Register 1 12 0x01 0x0C HPL Routing Selection Register 1 13 0x01 0x0D HPR Routing Selection Register 1 14 0x01 0x0E LOL Routing Selection Register 1 15 0x01 0x0F LOR Routing Selection Register 1 16 0x01 0x10 HPL Driver Gain Setting Register 1 17 0x01 0x11 HPR Driver Gain Setting Register 1 18 0x01 0x12 LOL Driver Gain Setting Register 1 19 0x01 0x13 LOR Driver Gain Setting Register 1 20 0x01 0x14 Headphone Driver Startup Control Register 1 21 0x01 0x15 Reserved Register 1 22 0x01 0x16 IN1L to HPL Volume Control Register 1 23 0x01 0x17 IN1R to HPR Volume Control Register 1 24 0x01 0x18 Mixer Amplifier Left Volume Control Register 1 25 0x01 0x19 Mixer Amplifier Right Volume Control Register 1 26-50 0x01 0x1A-0x32 Reserved Register 1 51 0x01 0x33 MICBIAS Configuration Register 1 52 0x01 0x34 Left MICPGA Positive Terminal Input Routing Configuration Register 1 53 0x01 0x35 Reserved Register 1 54 0x01 0x36 Left MICPGA Negative Terminal Input Routing Configuration Register 1 55 0x01 0x37 Right MICPGA Positive Terminal Input Routing Configuration Register 1 56 0x01 0x38 Reserved Register 1 57 0x01 0x39 Right MICPGA Negative Terminal Input Routing Configuration Register 1 58 0x01 0x3A Floating Input Configuration Register 1 59 0x01 0x3B Left MICPGA Volume Control Register 1 60 0x01 0x3C Right MICPGA Volume Control Register 1 61 0x01 0x3D ADC Power Tune Configuration Register 1 62 0x01 0x3E ADC Analog Volume Control Flag Register 1 63 0x01 0x3F DAC Analog Gain Control Flag Register 1 64-70 0x01 0x40-0x46 Reserved Register 1 71 0x01 0x47 Analog Input Quick Charging Configuration Register 1 72-122 0x01 0x48-0x7A Reserved Register 1 123 0x01 0x7B Reference Power-up Configuration Register 1 124 0x01 0x7C Charge Pump Control 1 125 0x01 0x7D Headphone Driver Configuration 1 126-127 0x01 0x7E-0x7F Reserved Register 8 0 0x08 0x00 Page Select Register 8 1 0x08 0x01 ADC Adaptive Filter Configuration Register 8 2-7 0x08 0x02-0x07 Reserved 8 8-127 0x08 0x08-0x7F ADC Coefficients Buffer-A C(0:29) 9-16 0 0x09-0x10 0x00 Page Select Register 9-16 1-7 0x09-0x10 0x01-0x07 Reserved Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 33 TLV320AIC3206 SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 www.ti.com Table 11. Summary of Register Map (continued) Decimal Hex DESCRIPTION PAGE NO. REG. NO. PAGE NO. REG. NO. 9-16 8-127 0x09-0x10 0x08-0x7F ADC Coefficients Buffer-A C(30:255) 26-34 0 0x1A-0x22 0x00 Page Select Register 26-34 1-7 0x1A-0x22 0x01-0x07 Reserved. 26-34 8-127 0x1A-0x22 0x08-0x7F ADC Coefficients Buffer-B C(0:255) 44 0 0x2C 0x00 Page Select Register 44 1 0x2C 0x01 DAC Adaptive Filter Configuration Register 44 2-7 0x2C 0x02-0x07 Reserved 44 8-127 0x2C 0x08-0x7F DAC Coefficients Buffer-A C(0:29) 45-52 0 0x2D-0x34 0x00 Page Select Register 45-52 1-7 0x2D-0x34 0x01-0x07 Reserved. 45-52 8-127 0x2D-0x34 0x08-0x7F DAC Coefficients Buffer-A C(30:255) 62-70 0 0x3E-0x46 0x00 Page Select Register 62-70 1-7 0x3E-0x46 0x01-0x07 Reserved. 62-70 8-127 0x3E-0x46 0x08-0x7F DAC Coefficients Buffer-B C(0:255) 34 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 TLV320AIC3206 www.ti.com SLAS649A – DECEMBER 2010 – REVISED DECEMBER 2010 REVISION HISTORY Changes from Revision initial (December 2010) to Revision A Page • Changed "mV" to "mVRMS" for Input signal level units ....................................................................................................... 8 • Changed Gain Error value from 0.7 to 0.8 ........................................................................................................................... 9 • Changed Gain Error value from 0.5 to 0.8 ........................................................................................................................... 9 • Changed Noise, Idle Channel value from 6.9 to 6.7 ............................................................................................................. 9 • Changed Bias voltage, Micbias Mode 0 value from 1.25 to 1.23 ....................................................................................... 10 • Changed Bias voltage, Micbias Mode 0 value from 1.25 to 1.23 ....................................................................................... 10 • Changed DAC Gain Error value from 0.4 to 0.5 ................................................................................................................. 11 • Changed DAC Gain Error value from 0.1 to 0.5 ................................................................................................................. 12 • Changed DAC channel separation condition from –1dB to –3dB ...................................................................................... 12 • Changed 10µF to 1µF in Reference Noise conditions statement ....................................................................................... 13 • Deleted min value from Decoupling Capacitor, changed typ value from 10 to 1µF ........................................................... 13 • Changed WCLK delay min from 14 to 30ns ....................................................................................................................... 14 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TLV320AIC3206 35 PACKAGE OPTION ADDENDUM www.ti.com 29-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TLV320AIC3206IRSBR ACTIVE WQFN RSB 40 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TLV320AIC3206IRSBT ACTIVE WQFN RSB 40 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TLV320AIC3206IRSBR Package Package Pins Type Drawing WQFN RSB 40 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 3000 330.0 12.4 Pack Materials-Page 1 5.3 B0 (mm) K0 (mm) P1 (mm) 5.3 1.5 8.0 W Pin1 (mm) Quadrant 12.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV320AIC3206IRSBR WQFN RSB 40 3000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated