EMP104-Q5 5.0 – 6.5 GHz Surface-Mounted PA UPDATED: 04/24/2008 FEATURES • • • • 5.0 – 6.5 GHz Operating Frequency Range 33.0dBm Output Power at 1dB Compression 17.0 dB Typical Small Signal Gain -44dBc OIMD3 @Each Tone Pout 22.0dBm APPLICATIONS • • Point-to-point and point-to-multipoint radio Military Radar Systems Caution! ESD sensitive device. ELECTRICAL CHARACTERISTICS (Ta = 25 °C, 50 ohm, VDD=10V, IDQ=1000mA) SYMBOL F P1dB Gss OIMD3 Input RL Output RL PARAMETER/TEST CONDITIONS MIN TYP MAX UNITS 6.5 GHz Operating Frequency Range 5.0 Output Power at 1dB Gain Compression 32.0 33.0 dBm Small Signal Gain Output 3rd Order Intermodulation Distortion @∆f=10MHz, Each Tone Pout 22.0dBm 15.0 17.0 dB -44 -40 dBc Input Return Loss -6 dB Output Return Loss -6 dB 1680 mA Idss Saturate Drain Current VDD Power Supply Voltage VDS =3V, VGS =0V 10 1 Rth Thermal Resistance Tb Operating Base Plate Temperature V o 7.5 -35 C/W +75 ºC ABSOLUTE MAXIMUM RATINGS FOR CONTINUOUS OPERATION2,3 SYMBOL CHARACTERISTIC CONTINUOUS VDS Drain to Source Voltage 10 V VGS Gate to Source Voltage -4 V IDD Drain Current IGSF Forward Gate Current PIN Input Power TCH Channel Temperature 150°C TSTG Storage Temperature -65/150°C PT Total Power Dissipation Idss 35mA @ 3dB compression 17W 1. Rth is mounting dependent. Measured result when used with Excelics recommended evaluation board. Adequate heat sinking recommended. 2. Operating the device beyond any of the above rating may result in permanent damage. 3. Bias conditions must also satisfy the following equation VDS*IDS < (TCH –THS)/RTH; where THS = ambient temperature Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 1 of 4 May 2008 EMP104-Q5 5.0 – 6.5 GHz Surface-Mounted PA UPDATED: 04/24/2008 CHIP OUTLINE AND PIN ASSIGNMENT Top View Bottom View 0.197±0.002 0.197±0.002 EMP104 -Q5 16 0.042 0.034 0.016 0 REF 15 1 11 5 10 0.008 0 REF 0.049 MAX 0.197±0.002 0 REF 0 REF 20 0.164 6 0.026±0.002 0.012±0.002 Additional Notes: 1) Ground Plane must be soldered to PCB RF ground 2) All dimensions are in inches 3) Refer to Excelics application notes on QFNs for further guidelines 4) Pin Assignment: Top View Vd1 RFin Bottom View Vd Vd2 EMP104 -Q5 Vd2 Vd1 16 20 15 RFout 1 RFout RFin 11 5 10 Vg 6 Vg Pin 1, 2, 4, 5 3 6 7, 8, 9, 10, 11, 12, 14, 15 13 16 17, 18, 19 20 Assignment NC RFin Vg NC RFout Vd2 NC Vd1 Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 2 of 4 May 2008 EMP104-Q5 5.0 – 6.5 GHz Surface-Mounted PA UPDATED: 04/24/2008 Typical Performance: 1. Small-Signal Parameters(@Vds = 10V, Ids = 1000mA) S21 S11 S22 40 25 39 24 38 23 37 22 36 21 35 20 34 19 33 18 32 17 31 16 30 G1dB(dB) P1dB(dBm) 2. P1-dB & G1-dB (@Vds = 10V, Ids = 1000mA) 15 4.8 5 5.2 5.4 5.6 5.8 6 6.2 6.4 6.6 Frequency(GHz) P1-dB G1-dB Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 3 of 4 May 2008 EMP104-Q5 5.0 – 6.5 GHz Surface-Mounted PA UPDATED: 04/24/2008 Recommended Circuit Schematic: g d 22uF 0.1uF 0.1uF Vd1 NC RFin NC NC RFout NC NC NC NC Vg 22uF Vd2 EMP104 -Q5 NC Vg NC NC NC 22uF NC NC NC NC 0.1uF Notes: 1) External bypass capacitors should be placed as close to the package as possible. 2) Dual biasing sequence required: a. Turn-on Sequence: Apply Vg = -2.5V, followed by Vd = 10V, lastly increase Vg until required Idq b. Turn-off Sequence: Turn off Vd, followed by Vg 3) Demonstration board available upon request. Specifications are subject to change without notice. Excelics Semiconductor, Inc. 310 De Guigne Drive, Sunnyvale, CA 94085 Phone: 408-737-1711 Fax: 408-737-1868 Web: www.excelics.com Page 4 of 4 May 2008