FERROXCUBE DATA SHEET E13/6/6 E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube E13/6/6 (814E250) E cores and accessories CORE SETS Effective core parameters SYMBOL PARAMETER 12.7 ±0.25 handbook, halfpage VALUE 9.5 ±0.25 3.2 ±0.13 UNIT Σ(I/A) core factor (C1) 1.37 mm−1 Ve effective volume 559 mm3 Ie effective length 27.7 mm Ae effective area 20.2 mm2 Amin minimum area 20.2 mm2 m mass of core half ≈ 1.4 g 4.1 ±0.13 5.7 ±0.13 6.4 ±0.13 CBW005 Dimensions in mm. Fig.1 E13/6/6 core half. Core halves AL measured in combination with a non-gapped core half, clamping force for AL measurements, 15 ±5 N. GRADE 3C90 AL (nH) µe AIR GAP (µm) 63 ±5% ≈ 70 ≈ 560 E13/6/6-3C90-A63 100 ±8% ≈ 110 ≈ 310 E13/6/6-3C90-A100 160 ±8% ≈ 175 ≈ 175 E13/6/6-3C90-A160 250 ±20% ≈ 275 ≈ 100 E13/6/6-3C90-A250 315 ±20% ≈ 340 ≈ 75 E13/6/6-3C90-A315 1470 ±25% ≈ 1605 ≈0 E13/6/6-3C90 TYPE NUMBER 3C92 1080 ±25% ≈ 1180 ≈0 E13/6/6-3C92 3C94 1470 ±25% ≈ 1605 ≈0 E13/6/6-3C94 3C96 1250 ±25% ≈ 1360 ≈0 E13/6/6-3C96 3F3 3F35 2008 Sep 01 63 ±5% ≈ 70 ≈ 560 E13/6/6-3F3-A63 100 ±8% ≈ 110 ≈ 310 E13/6/6-3F3-A100 160 ±8% ≈ 175 ≈ 175 E13/6/6-3F3-A160 250 ±20% ≈ 275 ≈ 100 E13/6/6-3F3-A250 315 ±20% ≈ 340 ≈ 75 E13/6/6-3F3-A315 1250 ±25% ≈ 1370 ≈0 E13/6/6-3F3 1000 ±25% ≈ 1090 ≈0 E13/6/6-3F35 315 Ferroxcube E13/6/6 (814E250) E cores and accessories Core halves of high permeability grades AL measured in combination with a non-gapped core half, clamping force for AL measurements, 15 ±5 N. AL (nH) µe AIR GAP (µm) 2600 ±25% ≈ 2840 ≈0 GRADE 3E27 TYPE NUMBER E13/6/6-3E27 Properties of core sets under power conditions B (mT) at CORE LOSS (W) at H = 250 A/m; f = 25 kHz; T = 100 °C f = 25 kHz; ˆ = 200 mT; B T = 100 °C f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C 3C90 ≥320 ≤ 0.06 ≤ 0.06 − − 3C92 ≥370 − ≤ 0.048 ≤ 0.33 − 3C94 ≥320 − ≤ 0.048 ≤ 0.33 − 3C96 ≥340 − ≤ 0.037 ≤ 0.25 − 3F3 ≥320 − ≤ 0.06 − ≤ 0.11 3F35 ≥300 − − − − GRADE Properties of core sets under power conditions (continued) B (mT) at CORE LOSS (W) at H = 250 A/m; f = 25 kHz; T = 100 °C f = 500 kHz; ˆ = 50 mT; B T = 100 °C f = 500 kHz; ˆ = 100 mT; B T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C 3C96 ≥340 ≤ 0.21 − − − 3F3 ≥315 − − − − 3F35 ≥300 ≤ 0.075 ≤ 0.6 − − GRADE Note 1. Measured at 60 °C. 2008 Sep 01 316 Ferroxcube E13/6/6 (814E250) E cores and accessories COIL FORMERS General data for E13/6/6 coil former ITEM SPECIFICATION Coil former material polyamide (PA6.6), glass reinforced, flame retardant in accordance with “UL 94V-2”; UL file number E41938(M) Maximum operating temperature 130 °C, “IEC 60085”, class B handbook, full pagewidth 9.25 max. 7.9 max. 4.5 6.5 3.2 min. ∅1.2 12.7 6.35 max. min. 7.6 CBW006 Dimensions in mm. Fig.2 E13/6/6 coil former. Winding data and area product for E13/6/6 coil former NUMBER OF SECTIONS MINIMUM WINDING AREA (mm2) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 15.4 6.5 32.0 311 2008 Sep 01 317 TYPE NUMBER CP-E13/6/6-1S Ferroxcube E13/6/6 (814E250) E cores and accessories General data for E13/6/6 coil former ITEM SPECIFICATION Coil former material polyphenylenesulfide (PPS), glass reinforced, flame retardant in accordance with “UL 94V-0”; UL file number E54700 Maximum operating temperature 130 °C, “IEC 60085”, class B handbook, full pagewidth 9.25 max. 7.9 max. 4.5 6.5 3.2 min. ∅1.2 12.7 6.35 max. min. 7.6 CBW006 Dimensions in mm. Fig.3 E13/6/6 coil former. Winding data and area product for E13/6/6 coil former NUMBER OF SECTIONS MINIMUM WINDING AREA (mm2) NOMINAL WINDING WIDTH (mm) AVERAGE LENGTH OF TURN (mm) AREA PRODUCT Ae x Aw (mm4) 1 15.4 6.5 32.0 311 2008 Sep 01 318 TYPE NUMBER CP-E13/6/6-1S-A Ferroxcube E13/6/6 (814E250) E cores and accessories DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 319