HMC-ALH459 v01.1207 LOW NOISE AMPLIFIERS - CHIP 1 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz Typical Applications Features This HMC-ALH459 is ideal for: Noise Figure: <5 dB • Short Haul / High Capacity Links P1dB: +7 dBm • Wireless LANs Gain: 14 dB • Automotive Radar Supply Voltage: +2.4V • Military & Space 50 Ohm Matched Input/Output • E-Band Communication Systems Die Size: 3.10 x 1.60 x 0.1 mm Functional Diagram General Description The HMC-ALH459 is a three stage GaAs HEMT MMIC Low Noise Amplifier (LNA) which operates between 71 and 86 GHz. The HMC-ALH459 features 14 dB of small signal gain, 4.5 dB of noise fi gure and an output power of +7 dBm at 1dB compression from two supply voltages at 2.1V and 2.4V respectively. All bond pads and the die backside are Ti/Au metallized and the amplifier device is fully passivated for reliable operation. This versatile LNA is compatible with conventional die attach methods, as well as thermocompression and thermosonic wire bonding, making it ideal for MCM and hybrid microcircuit applications. All data shown herein is measured with the chip in a 50 Ohm environment and contacted with RF probes. Electrical Specifi cations [1], TA = +25° C Vdd1=Vdd2 = 2.1V, Vdd3=2.4V, Idd1+Idd2+Idd3 = 30 mA [2] Parameter Min. Frequency Range Typ. Max. 71 - 86 GHz 14 dB 4.5 dB Input Return Loss 8 dB Output Return Loss 10 dB Output Power for 1 dB Compression (P1dB) 7 dBm Supply Current (Idd1+Idd2+Idd3) 30 mA Gain 13 Noise Figure [1] Unless otherwise indicated, all measurements are from probed die [2] Adjust Vgg1=Vgg2 between -1V to +0.3V (typ -0.5V )to achieve Idd total = 30 mA 1 - 200 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-ALH459 v01.1207 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz 18 8 16 7 NOISE FIGURE (dB) 14 12 GAIN (dB) 1 Noise Figure vs. Frequency 10 8 6 4 6 5 4 3 2 1 2 0 0 70 72 74 76 78 80 82 84 86 88 90 74 76 78 80 82 84 86 88 90 FREQUENCY (GHz) FREQUENCY (GHz) Input Return Loss vs. Frequency Output Return Loss vs. Frequency 0 0 -5 -2 RETURN LOSS (dB) RETURN LOSS (dB) -4 -10 -15 -20 -25 -30 -6 -8 -10 -12 LOW NOISE AMPLIFIERS - CHIP Linear Gain vs. Frequency -14 -16 -35 -18 -20 -40 70 72 74 76 78 80 82 FREQUENCY (GHz) 84 86 88 90 70 72 74 76 78 80 82 84 86 88 90 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1 - 201 HMC-ALH459 v01.1207 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz LOW NOISE AMPLIFIERS - CHIP 1 Absolute Maximum Ratings Drain Bias Voltage +3 Vdc Gate Bias Voltage -1 to +0.3 Vdc RF Input Power -5 dBm Thermal Resistance (channel to die bottom) 195.6 °C/W Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Die Packaging Information [1] NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM]. Standard Alternate WP - 19 [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. 1 - 202 2. TYPICAL BOND PAD IS .004” SQUARE. 3. BACKSIDE METALLIZATION: GOLD. 4. BACKSIDE METAL IS GROUND. 5. BOND PAD METALLIZATION: GOLD. 6. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. 7. OVERALL DIE SIZE ±.002” For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-ALH459 v01.1207 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz Pad Number Function Description 1 RFIN This pad is AC coupled and matched to 50 Ohms. 2-4 Vdd1, Vdd2, Vdd3 5 RFOUT 6-8 Vgg1, Vgg2, Vgg3 Gate control for amplifier. Please follow “MMIC Amplifier Biasing Procedure” application note. See assembly for required external components. Die bottom GND Die bottom must be connected to RF/DC ground. Interface Schematic Power Supply Voltage for the amplifier. See assembly for required external components. This pad is AC coupled and matched to 50 Ohms. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com LOW NOISE AMPLIFIERS - CHIP 1 Pad Descriptions 1 - 203 HMC-ALH459 v01.1207 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz Assembly Diagram LOW NOISE AMPLIFIERS - CHIP 1 1 - 204 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-ALH459 v01.1207 GaAs HEMT LOW NOISE AMPLIFIER, 71 - 86 GHz The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane Microstrip substrates should be placed as close to the die as possible in order to minimize bond wire length. Typical die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils). 0.127mm (0.005”) Thick Alumina Thin Film Substrate Figure 1. Handling Precautions Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: strikes. 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane Follow ESD precautions to protect against ESD Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. LOW NOISE AMPLIFIERS - CHIP 1 Mounting & Bonding Techniques for Millimeterwave GaAs MMICs 0.150mm (0.005”) Thick Moly Tab 0.254mm (0.010”) Thick Alumina Thin Film Substrate Figure 2. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1 - 205