HMC341 v01.1007 LOW NOISE AMPLIFIERS - CHIP 1 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz Typical Applications Features The HMC341 is ideal for: Excellent Noise Figure: 2.5 dB • Millimeterwave Point-to-Point Radios Gain: 13 dB • LMDS Single Supply: +3V @ 30 mA • VSAT & SATCOM Small Size: 1.42 x 1.06 x 0.1 mm Functional Diagram General Description The HMC341 chip is a GaAs MMIC Low Noise Amplifier (LNA) which covers the frequency range of 24 to 30 GHz. The chip can easily be integrated into Multi-Chip Modules (MCMs) due to its small (1.51 mm2) size. The chip utilizes a GaAs PHEMT process offering 13 dB gain from a single bias supply of + 3V @ 30 mA with a noise figure of 2.5 dB. All data is with the chip in a 50 ohm test fixture connected via 0.025 mm (1 mil) diameter wire bonds of minimal length 0.31 mm (<12 mils). Electrical Specifi cations, TA = +25° C, Vdd = +3V Parameter Min. Frequency Range Gain 10 Gain Variation Over Temperature 26 - 30 GHz 24 - 26 GHz Noise Figure Max. Units GHz 13 16 dB 0.03 0.04 dB/°C 2.5 2.9 3.5 3.9 dB dB Input Return Loss 9 13 Output Return Loss 9 13 dB Reverse Isolation 25 30 dB dB Output Power for 1dB Compression (P1dB) 2 6 dBm Saturated Output Power (Psat) 6 10 dBm Output Third Order Intercept (IP3) 12 16 dBm Supply Current (Idd) 1-8 Typ. 24 - 30 30 40 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC341 v01.1007 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz 20 15 15 10 +25C -55C +85C 10 +25C -55C +85C 5 0 0 22 24 26 28 30 32 22 24 FREQUENCY (GHz) Return Loss @ Vdd = +3V 30 32 30 32 30 32 0 S11 S22 -5 RETURN LOSS (dB) -5 RETURN LOSS (dB) 28 Return Loss @ Vdd = +5V 0 -10 -15 -20 -25 -30 S11 S22 -10 -15 -20 -25 -30 -35 -35 22 24 26 28 30 32 22 24 FREQUENCY (GHz) 26 28 FREQUENCY (GHz) Noise Figure vs. Temperature @ Vdd = +3V Noise Figure vs. Temperature @ Vdd = +5V 7 7 6 6 +25C -55C +85C 5 NOISE FIGURE (dB) NOISE FIGURE (dB) 26 FREQUENCY (GHz) LOW NOISE AMPLIFIERS - CHIP 20 5 1 Gain vs. Temperature @ Vdd = +5V GAIN (dB) GAIN (dB) Gain vs. Temperature @ Vdd = +3V 4 3 2 1 +25C -55C +85C 5 4 3 2 1 0 0 22 24 26 28 FREQUENCY (GHz) 30 32 22 24 26 28 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1-9 HMC341 v01.1007 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz Isolation 13.6 3.8 0 13.4 3.6 -10 13.2 3.4 13 3.2 ISOLATION (dB) GAIN dB) Gain & Noise Figure vs. Supply Voltage @ 28 GHz NOISE FIGURE (dB) -30 3 12.6 2.8 12.4 2.6 12.2 2.4 -60 2.2 -70 2.5 3 3.5 4 4.5 5 Vdd = +3V Vdd = +5V -20 12.8 12 -40 -50 22 5.5 24 Output P1dB @ Vdd = +3V 16 14 14 P1dB (dBm) 8 6 8 6 4 2 2 +25 C -55 C +85 C 0 22 24 26 28 30 32 22 24 FREQUENCY (GHz) 28 30 32 30 32 Output IP3 @ Vdd = +5V 25 20 20 15 15 IP3 (dBm) 25 +25 C -55 C +85 C 10 26 FREQUENCY (GHz) Output IP3 @ Vdd = +3V IP3 (dBm) 32 10 4 0 5 +25 C -55 C +85 C 10 5 0 0 22 24 26 28 FREQUENCY (GHz) 1 - 10 30 12 +25 C -55 C +85 C 10 28 Output P1dB @ Vdd = +5V 16 12 26 FREQUENCY (GHz) Vdd SUPPLY VOLTAGE (Vdc) P1dB (dBm) LOW NOISE AMPLIFIERS - CHIP 1 30 32 22 24 26 28 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC341 v01.1007 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz 1 Absolute Maximum Ratings +5.5 Vdc RF Input Power (RFIN)(Vdd = +3.0 Vdc) +3 dBm Channel Temperature 175 °C Continuous Pdiss (T = 85 °C) (derate 3.44 mW/°C above 85 °C) 0.310 W Thermal Resistance (channel to die bottom) 290 °C/W Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C LOW NOISE AMPLIFIERS - CHIP Drain Bias Voltage (Vdd) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Die Packaging Information [1] Standard Alternate GP-2 [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM] 2. DIE THICKNESS IS .004” 3. TYPICAL BOND IS .004” SQUARE 4. BACKSIDE METALLIZATION: GOLD 5. BOND PAD METALLIZATION: GOLD 6. BACKSIDE METAL IS GROUND. 7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1 - 11 HMC341 v01.1007 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz LOW NOISE AMPLIFIERS - CHIP 1 1 - 12 Pad Descriptions Pad Number Function Description 1 RFIN This pad is AC coupled and matched to 50 Ohms. 2 RFOUT This pad is AC coupled and matched to 50 Ohms. 3 Vdd Power Supply for the 2-stage amplifier. An external RF bypass capacitor of 100 - 300 pF is required. The bond length to the capacitor should be as short as possible. The ground side of the capacitor should be connected to the housing ground. Interface Schematic Assembly Diagrams For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC341 v01.1007 GaAs MMIC LOW NOISE AMPLIFIER, 24 - 30 GHz The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane 0.127mm (0.005”) Thick Alumina Thin Film Substrate Microstrip substrates should brought as close to the die as possible in order to minimize bond wire length. Typical die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils). An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer capacitor (mounted eutectically or by conductive epoxy) placed no further than 0.762mm (30 Mils) from the chip is recommended. Handling Precautions Figure 1. 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: strikes. Follow ESD precautions to protect against ESD RF Ground Plane 0.150mm (0.005”) Thick Moly Tab LOW NOISE AMPLIFIERS - CHIP 1 Mounting & Bonding Techniques for Millimeterwave GaAs MMICs 0.254mm (0.010”) Thick Alumina Thin Film Substrate Figure 2. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of 150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 1 - 13