Approved by: Checked by: Issued by: SPECIFICATION PRODUCT: SAW FILTER MODEL: HF65801N （F811CPL） SIP5D HOPE MICROELECTRONICS CO.,LIMITED Tel:+86-755-82973806 Fax:+86-755-82973550 E-mail: [email protected] http://www.hoperf.com Page 1 of 1 1.Construction 1.1 Dimension and materials Type : F65801N 1.2. Circuit construction, measurement circuit 2.Characteristics Standard atmospheric conditions Unless otherwise specified , the standard rang of atmospheric conditions for making measurements and tests is as follows; Ambient temperature : 15℃ to 35℃ Relative humidity : 25% to 85% Air pressure : 86kPa to 106kPa 1 Operating temperature rang Operating temperature rang is the rang of ambient temperatures in which the filter can be operated continuously. -10℃ ~ +60℃ Storage temperature rang Storage temperature rang is the rang of ambient temperatures at which the filter can be stored without damage. Conditions are as specified elsewhere in these specifications. -40℃ ~ +70℃ Reference temperature +25℃ 2.1 Maximum Rating DC voltage AC voltage VDC Vpp 12 10 V V Between any terminals Between any terminals 2.2 Electrical Characteristics: Characteristics of channel 1（PIF） Source impedance Load impedance Item Insertion attenuation Reference level Zs=50Ω ZL=2kΩ//3pF Freq min TA=25℃ typ max 57.08MHz 14.6 16.6 18.6 dB 58.83MHz 55.25MHz Relative attenuation 54.33MHz 52.83MHz 60.33MHz 45.08~52.83MHz Sidelobe 60.33~65.08MHz Temperature coefficient 6.7 18.0 40.0 40.0 30.0 30.0 5.2 -0.9 31.0 54.0 45.0 41.0 38.0 -72 3.7 2.0 - dB dB dB dB dB dB dB ppm/k Characteristics of channel 2（SIF） Source impedance Load impedance Item Insertion attenuation Reference level Zs=50Ω ZL=2kΩ//3pF Freq min TA=25℃ typ max 54.33MHz 14.0 16.0 18.0 dB 52.83MHz 55.25MHz Relative attenuation 58.75MHz 60.33MHz 45.08~52.83MHz Sidelobe 60.33~65.08MHz Temperature coefficient 23.0 12.0 30.0 30.0 25.0 27.0 30.0 18.0 39.0 37.0 29.0 32.0 -72 - dB dB dB dB dB dB ppm/k 2 2.3 Environmental Performance Characteristics Item Test condition Allowable change of absolute Level at center frequency(dB) High temperature test < 1.0 70℃ 1000H Low temperature test < 1.0 -40℃ 1000H Humidity test < 1.0 40℃ 90-95% 1000H Thermal shock < 1.0 -20℃==25℃==80℃ 20 cycle 30M 10M 30M Solder temperature test < 1.0 Sold temp.260℃ for 10 sec. Soldering More then 95% of total Immerse the pins melt solder area of the pins should be covered with solder at 260℃+5/-0℃ for 5 sec. 2.4 Mechanical Test Item Test condition Vibration test 600-3300rpm amplitude 1.5mm 3 directions 2 H each Drop test On maple plate from 1 m high 3 times Lead pull test Pull with 1 kg force for 30 seconds Lead bend test 90o bending with 500g weigh 2 times 2.5 Voltage Discharge Test Item Test condition Surge test Between any two electrode Allowable change of absolute Level at center frequency(dB) <1.0 <1.0 <1.0 <1.0 Allowable change of absolute Level at center frequency(dB) <1.0 3