TI TL16PNP200

SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
D PnP Card Autoconfiguration Sequence
D
D
D
D
D
D
D Simple 3-Terminal Interface to Serial
Compliant
Satisfies All Requirements for Qualifying
for the Windows 95 Logo
Supports up to Five Logical Devices
24-Bit Memory Address Decoding and
16-Bit I/O Address Decoding With
Programmable (1, 2, 4, 8, 16, 32, 64)
I/O Block Size
Device Interrupt Mapping to Any of the 11
Interrupt Request (IRQ) Signals on Industry
Standard Architecture (ISA) Bus
Direct Memory Access (DMA) Support For
Two Logical Devices with Configurable
DMA Channel Connection
Configurable OEN Signals That Can Be
Used to Enabled Logical Device
Transceivers
D
D
D
D
D
EEPROM 2K/4K ST93C56/66 or Equivalent
for Resource Data Storage and Power-Up
Defaults, As Well As General
Board-Specific Data
Default Configuration Loading and
Activation Upon Power-up for Non-PnP
Systems
Two Modes of Operation That Satisfy A
Wide Range of Applications
Direct Connection to ISA/AT Bus Without
Need for Buffers
5-V Power Supply Operation
Available in 80-pin PQFP
description
The TL16PNP200 is an ISA plug-and-play (PnP) controller that provides autoconfiguration capability to ISA
cards according to the ISA PnP 1.0 a specification. It interfaces to a serial EEPROM where card resource
requirements and power-up defaults are stored. On power up, the controller loads the default configuration from
the EEPROM making it ready for operation (non-PnP systems) or to be configured by the PnP configuration
process (PnP-capable systems). During configuration mode, the PnP autoconfiguration process reads the card
resource requirements, configures the card by writing to the TL16PNP200 configuration registers, activates the
device, and removes it from the configuration mode. Thereafter, the TL16PNP200 routes all ISA transactions
between the card and the ISA bus. The TL16PNP200 operates in one of two modes. In mode 0, the device
supports two logical devices with memory, I/O, interrupt, and DMA resources for each device. In mode 1, the
device supports five logical devices with I/O and interrupt resources for all logical devices and DMA resources
for two of the five logical devices; there is no memory support in mode 1. The TL16PNP200 provides interface
signals to allow on-board logic access to the serial EEPROM.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Windows 95 is a trademark of Microsoft Corporation .
Copyright  1996, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!#- '# #!#&, !&"'#
#- && $##(
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
1
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
SCS
SCLK
SIO
GND
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ9
IRQ10
IRQ11
IRQ12
IRQ14
IRQ15
CDRQ0
CDRQ1
CDRQ2
VCC
CDACK0
CDACK1
CDACK2
CLK
RESET
PH PACKAGE
(TOP VIEW)
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
PNP_BUSY
DMA_ACK1
DMA_ACK0
VCC
SROM_BUSY
DMA_RQ1
DMA_RQ0
INTR1
INTR0
GND
IOCS0
IOCS1
MCS1(IOCS2)
MCS0(IOCS3)
OEN0
BALE(OEN1)
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
GND
A23(IOCS4)
A22(CDRQ4)
A21(CDRQ3)
A20(CDACK4)
A19(CDACK3)
A18(INTR4)
A17(INTR3)
A16(INTR2)
VCC
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
AEN
IOW
IOR
GND
D0
D1
D2
D3
VCC
D4
D5
D6
D7
GND
A0
A1
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
functional block diagram
D7−D0
28−31, 33−36
8
MCS1† (IOCS2),
MCS0† (IOCS3)
77−78
(INTR4−INTR2),
INTR1−INTR0
(7−9),72−73
DMA_RQ1,
DMA_RQ0
70−71
DMA_ACK1,
DMA_ACK0
66−67
(IOCS4),
IOCS1−IOCS0
(2), 76−75
Output
Enable
64
EEPROM
Controller
8
Card Control
40
11−26, 2−9
A23−A16†, A15−A0
SIO
PNP_BUSY
SROM_BUSY
8
Logical
Device
Decoder
60−50
IRQ3−IRQ7,
IRQ9−IRQ12,
IRQ14−IRQ15
(CDACK4−CDACK3),
CDACK2−CDACK0
SCLK
8
80−79
(OEN1), OEN0
(CDRQ4−CDRQ3),
CDRQ2−CDRQ0
SCS
63
62
65
69
Logical Device
Control
8
Logical Device
Configuration
8
(3−4), 47−49
8
(5−6), 43−45
8
11−26, 2−9
AEN
BALE†
IOR
IOW
RESET
Read-Data Port
40
80
38
39
41
8
Write-Data Port
Decoder
Address Port
Address
Register
Select
LFSR
Key
Enable
† Designates terminals for mode 0 only.
NOTE A: Terminals in parentheses are for mode 1 operation only.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
3
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
Terminal Functions
TERMINAL
NAME
A15-A0
NO.
I/O
DESCRIPTION
11-26
I
Address. A15-A0 connects to ISA address bits SA15-SA0.
A16 (INTR2),†
A17 (INTR3),†
A18 (INTR4)†
9-7
I
Address (Interrupt). In Mode 0, A16−A18 should be connected to ISA address bits SA16, LA17, and LA18
respectively. In Mode 1, INTR2−INTR4 are interrupt requests from logical devices 2, 3, and 4 respectively.
A19 (CDACK3),†
A20 (CDACK4)†
6, 5
I
Address (DMA acknowledge). In Mode 0, A19−A20 should be connected to ISA address bits LA19 and
LA20. In Mode 1, CDACK3 and CDACK4 are configurable data acknowledge signals and should be
connected to the ISA DACK signals of the selected DMA channels as specified by DMA mapping in the
power-up defaults.
A21 (CDRQ3),†
A22 (CDRQ4)†
4, 3
I/O
Address (DMA request). In Mode 0, A21 and A22 are inputs that should be connected to ISA address bits
LA21 and LA22. In Mode 1, CDRQ3 and CDRQ4 are configurable data request outputs and should be
connected to the ISA DRQ signals of the selected DMA channels as specified by DMA mapping in the
power-up defaults.
A23 (IOCS4)†
2
I/O
Address (I/O chip select). In Mode 0, A23 is an input that should be connected to ISA address bit LA23.
In Mode 1, IOCS4 is a I/O chip select output for logical device 4.
AEN
40
I
ISA address enable. During DMA operation, AEN is an active signal that prevents the controller from
generating an I/O chip select.
BALE (OEN1)†
80
I/O
ISA bus address latch enable (output enable). In Mode 0, BALE is an ISA input which is used to latch the
upper address. In Mode 1, OEN1 is an output enable and can be configured to respond to I/O read
operations to any logical device, which can use it to enable its transceivers.
CDACK0,
CDACK1,
CDACK2
45-43
I
Configurable ISA DMA acknowledge. CDACK0 − CDACK2 should be connected to the ISA DACK signals
of the selected DMA channels as specified by DMA mapping in the power-up defaults.
CDRQ0, CDRQ1,
CDRQ2
49-47
O
Configurable ISA DMA data request. CDRQ0−CDRQ2 should be connected to the ISA DRQ signals of the
selected DMA channels as specified by DMA mapping in the power-up defaults.
10-22 MHz clock. CLK is an input from the OSC signal on the ISA bus.
CLK
42
I
D0-D7
31-28,
36-33
I/O
8-bit ISA data
DMA_ACK0,
DMA_ACK1
67, 66
O
DMA acknowledge. DMA_ACK0 and DMA_ACK1 are used for DMA acknowledge to logical devices 0 and
1.
DMA_RQ0,
DMA_RQ1
71, 70
I
DMA requests. DMA_RQ0 and DMA_RQ1 are used for DMA requests from logical devices 0 and 1.
GND
1, 27,
37, 61,
74
INTR0, INTR1
73, 72
I
Interrupt requests. INTR0 and INTR1 generate interrupt requests from logical devices 0 and 1.
IOCS0, IOCS1
75, 76
O
I/O chip select outputs to logical devices 0 and 1. The address decoder decodes the full 16-bit I/O address
and generates the I/O chip select signals based on the selected I/O block size.
38
I
ISA I/O read.
IOR
IOW
Ground (0 V). All terminals must be tied to GND for proper operation.
39
I
ISA I/O write.
IRQ3−IRQ7,
IRQ9−IRQ12,
IRQ14, IRQ15
50-60
O
ISA Interrupt request. These signals should be connected to the corresponding ISA IRQ signals.
MCS0(IOCS3),†
MCS1(IOCS2)†
78, 77
O
Memory chip select (I/O chip select). In Mode 0, MCS0 and MCS1 are the memory chip select outputs for
logical devices 0 and 1. A 24-bit memory address is decoded to generate the memory chip select signals
based on the selected memory block size. In Mode 1, IOCS3 and IOCS2 are the I/O chip select outputs
for logical devices 3 and 2.
79
O
Output enable. OEN0 can be configured to respond to I/O read operations to any logical device, which can
use it to enable its transceivers.
OEN0
† Terminal names in parenthesis indicate when the device is in mode 1 operation.
4
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
PNP_BUSY
65
O
Plug-and-play busy. PNP_BUSY signal requests access to the EEPROM and is asserted during PNP
configuration. On-board logic uses this signal to determine when it can access the EEPROM. This signal
can also be used as a soft reset.
RESET
41
I
Reset. When active (high), RESET clears most logical device registers and puts the TL16PNP200 in the
wait-for-key state. All configuration registers are loaded with their power-up defaults, and card select
number (CSN) is reset to 0.
SCLK
63
O
Serial clock (3-state output path). SCLK controls the serial bus timing for address and data. A 100 µA
pulldown transistor is connected internally to this terminal.
SCS
64
O
EEPROM chip select. SCS controls the activity of the EEPROM. A 100 mA pulldown transistor is connected
internally to this terminal.
SIO
62
I/O
Serial input/output. SIO is a 3-state bidirectional EEPROM I/O data path. A 100 µA pulldown transistor is
connected internally to this terminal .
SROM_BUSY
69
I
VCC
10,32,
46,68
Serial EEPROM busy. SROM_BUSY is asserted by on-board logic during its access to the EEPROM.
5-V supply voltage.
detailed description
modes of operation
The TL16PNP200 operates in one of two modes: Mode 0 or Mode1. The mode is selected by setting the mode
bit in the power-up defaults (see defaults format section).
Mode 0:
•
•
•
•
Supports two logical devices
Supports memory, I/O, IRQ, and DMA for each of the two logical devices
Routes device DMA request to three DMA channels that can be connected to any three DMA channels
on the ISA bus
Has one configurable OEN signal
Mode 1:
•
•
•
•
Supports five logical devices
Supports I/O and IRQ for the five logical devices and supports DMA for two logical devices
Routes device DMA requests to five DMA channels that can be connected to any five DMA channels on
the ISA bus
Has two configurable OEN signals
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
5
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
EEPROM interface
This device interfaces to a SGS Thomson 2 kbit ST93C56, or 4 kbit ST93C66 compatible EEPROM. In addition
to the three EEPROM signals (SCS, SCLK, and SIO), the two interface signals (PNP_BUSY and SROM_BUSY)
are provided to allow optional on-board logic access to the EEPROM. On power-up or reset, the TL16PNP200
gains access to the EEPROM and asserts the PNP_BUSY output high indicating that the device is in the
configuration mode and is accessing the EEPROM. After the configuration is complete, the device goes to the
wait-for-key state, puts SIO, SCLK, and SCS outputs into a high impedance state (these signals are pulled down
internally), and deasserts the PNP_BUSY signal. On-board logic can assert to the SROM_BUSY signal at any
time to request access to the EEPROM, then SROM_BUSY can start accessing the EEPROM after 2 clock
cycles when PNP_BUSY is deasserted; otherwise, SROM_BUSY must wait until PNP_BUSY is deasserted.
In a similar manner, the device uses the PNP_BUSY signal to request access to the EEPROM. In that case
on-board logic should stop accessing the EEPROM and deassert SROM_BUSY, after which the device starts
accessing the EEPROM (see Figure 1). If on-board logic does not need to access the EEPROM, SROM_BUSY
should be tied to ground and PNP_BUSY should be left unconnected. All unused inputs should be tied to the
inactive state, and all unused outputs should be left open.
NOTE
If the TL16PNP200 enters the configuration mode again and leaves the wait-for-key state, the wake
command generates a read transaction from address 0x0E, which is the beginning of the card
resource data.
CLK
PNP_BUSY
SROM_BUSY
(1)
(2)
(3)
(4)
(5)
The following steps reflect the EEPROM interface:
(1) The device finishes accessing the EEPROM.
(2) On-board logic requests access to the EEPROM (can be any time).
(3) On-board logic starts accessing the EEPROM since PNP_BUSY is low.
(4) The device requests access to the EEPROM.
(5) On-board logic relinquishes the EEPROM.
(6) The device starts accessing the EEPROM.
Figure 1. EEPROM Interface Signals
6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
(6)
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
default format
On power up or reset, the TL16PNP200 starts generating read operations to the EEPROM. Each read
transaction consists of read opcode, address, and data cycles (see EEPROM section). The data cycle is
comprised to 16-bits. EEPROM addresses 0x00 through 0x0D store the power-up defaults. These defaults
include the PnP configuration register defaults, I/O block size, DMA mapping, and OEN configuration. Table 1
is a description of the format for storing the defaults in the EEPROM.
Table 1. Default Format
ADDRESS
DESCRIPTION
0x00
LD0 Memory base address bits 23-8 (Note 1)
0x01
LD1 Memory base address bits 23-8 (Note 1)
0x02
LD0 Memory upper address bits 23-8 (Note 1)
0x03
LD1 Memory upper address bits 23-8 (Note 1)
0x04
LD0 I/O Base address bits 15-0
0x05
LD1 I/O Base address bits 15-0
0x06
LD2 I/O Base address bits 15-0 (Note 2)
0x07
LD3 I/O Base address bits 15-0 (Note 2)
0x08
LD4 I/O Base address bits 15-0 (Note 2)
0x09
Bits 15-13: LD0 I/O block size, bits 12-10: LD1 I/O block size, bits 9-7: LD2 I/O block size, bits 6-4: LD3 I/O block size, bits
3-1: LD4 I/O block size (Note 3)
0x0A
Bits 15-12: LD0 IRQ level, bits 11-8: LD1 IRQ level, bits 7-4: LD2 IRQ level, bits 3-0: LD3 IRQ level (Note 4)
0x0B
Bits 15-12: LD4 IRQ level, bits 11-9 LD0: DMA channel, bits 8-6: LD1 DMA channel (Note 5)
0x0C
Bit 15: LD0 active, bit 14: LD1 active, bit 13: LD2 active, bit 12: LD3 active, bit 11: LD4 active, bits 10-8: OEN0 configuration,
bits 7-5: OEN1 configuration, bit 4: mode (Note 6)
0x0D
Bits 14-12: DMA 4 mapping, bits 11-9: DMA 3 mapping, bits 8-6: DMA 2 mapping, bits 5-3: DMA 1 mapping,
bits 2-0: DMA 0 mapping (Note 7)
NOTES: 1.
2.
3.
4.
5.
6.
7.
In Mode 1, these fields are ignored.
In Mode 0, these fields are ignored.
Bit 0 is unused, and in Mode 0 bits 9-1 are ignored.
In Mode 0 bits 7-0 are ignored.
Bits 5-0 are unused, and in Mode 0 bits 15-12 are ignored.
Bits 3-0 are unused, and in Mode 0 bits 13-11 and bits 7-5 are ignored.
Bit 15 is unused, and in Mode 0 bits 14-9 are ignored.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
7
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
default format (continued)
The formats for the coded fields are as follows:
Table 2. I/O Block Size
BLOCK SIZE
ADDRESS BITS
DECODED
000
1 byte
15-0
001
2 bytes
15-1
010
4 bytes
15-2
CODE
011
8 bytes
15-3
100
16 bytes
15-4
101
32 bytes
15-5
110
64 bytes
15-6
Table 3. OEN0 Configuration - Mode 0
CODE
LOGICAL DEVICE
000
LD0
001
LD1
010
LD0 or LD1
Table 4. OEN0 and OEN1 Configuration - Mode 1
CODE
LOGICAL DEVICE
000
LD0
001
LD1
010
LD2
011
LD3
100
LD4
The IRQ level field is the IRQ level number (e.g. 0011 for IRQ3, 0100 for IRQ4, ... etc.), and the DMA channel
field is the DMA channel number (e.g. 000 for DMA channel 0, 001 for DMA channel 1, ... etc.). The LDn Active
bits should be set to 1 when device n is required to be active on power-up or after reset, otherwise it is cleared
to 0. The mode bit should be 0 for Mode 0 operation and 1 for Mode 1 operation.
The DMA mapping fields tell the TL16PNP200 which ISA DMA channels are connected to the device. For
example, in Mode 0 any three ISA DMA channels can be connected to the device. When DMA channels 0, 3,
and 5 are connected to CDRQ0/CDACK0, CDRQ1/CDACK1, and CDRQ2/CDACK2, respectively, then DMA
0 mapping field should be 000, DMA 1 mapping field should be 011, and DMA 2 mapping field should be 101.
8
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (See Note 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6 V
Input voltage range, VI: Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC +0.5 V
Fail safe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V
Output voltage range, VO: Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC +0.5 V
Fail safe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 8. This applies for external output and bidirectional buffers. VO > VCC does not apply to fail-safe terminals..
9. This applies for external input and bidirectional buffers. VI > VCC does not apply to fail-safe terminals.
recommended operating conditions
Supply voltage, VCC
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
High-level input voltage, VIH
2
0
VCC
0.8
V
Low-level input voltage, VIL
Operating free-air temperature, TA
0
70
°C
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
V
9
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP†
MAX
VCC −0.8
VCC −0.8
UNIT
VOH
High-level output voltage
IOH = − 4 mA (see Note 10)
IOH = − 12 mA (see Note 11)
VOL
Low-level output voltage
IOL = 4 mA (see Note 10)
IOL = 12 mA (see Note 11)
Il
Input current
VCC = 5.25 V,
VI = 0 to 5.25 V,
VSS = 0,
All other pins floating
±1
µA
A
IOZ
High-impedance-state output
current
VCC = 5.25 V,
VSS = 0,
VO = 0 to 5.25 V,
Pullup transistors and pulldown transistors are off
± 10
µA
ICC
Supply current
VCC = 5.25 V,
All inputs toggle
No load on outputs
Ci(CLK)
Clock input capacitance
V
0.5
0.5
TA = 25
25°C,
C,
f = 22 MHz,
fCLK
Clock frequency
† All typical values are at VCC = 5 V and TA = 25°C.
NOTES: 10. These parameters apply for all outputs except D7 −D0, IRQ and CDRQ outputs.
11. These parameters only apply for D7 −D0, IRQ , and CDRQ outputs.
V
25
mA
5
pF
10
22
MHz
serial EEPROM clock timing requirements over recommended ranges of supply voltage and
operating free-air temperature
ALTERNATE
SYMBOL
PARAMETER
tw(SCLKH)
tw(SCLKL)
Pulse duration, SCLK high to low (see Note 12)
fCLK
SCLK clock frequency (see Note 13)
td1
td2
Delay time, CS high to SCLK high
TEST CONDITIONS
tCHCL
tCLCH
Pulse duration, SCLK low to high (see Note 12)
MIN
250
See Figure 9
tSHCH
tDVCH
tpd1
Propagation delay time, SCLK high to input level
transition
tCHDX
tpd2
Propagation delay time, SCLK high to output valid
tCHQV
tpd3
Propagation delay time, SCLK low to CS transition
tCLSL
See Figure 9
See Figures 9 and 10
ns
0.68
MHz
50
ns
100
ns
100
ns
500
See Figure 10
UNIT
ns
250
0.3
Delay time, SIO input valid to SCLK high
MAX
2
ns
clock
period
td3
Delay time, CS low to output Hi-Z
tSLQZ
100
ns
NOTES: 12. The ST93C56 chip select, S, must be brought low for a minimum of 250 ns (tSLSH) between consecutive instruction cycles per the
ST93C56 specification.
13. The SCLK signal is attained by dividing the internal CLK signal frequency by 32.
10
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
system timing requirements and switching characteristics over recommended ranges of supply
voltage and operating free-air temperature
PARAMETER
ALT SYMBOL
FIGURE
TEST
CONDITIONS
MIN
MAX
UNIT
tw1
Pulse duration, write strobe (IOW)
tWR
6
2
clock
periods
tw2
Pulse duration, read strobe (IOR)
tRD
5
3
clock
periods
tw3
tsu1
Pulse duration, reset
tRST
tDS
1
µs
6
10
ns
tsu2
tsu3
Setup time, address (A23-A0) valid before IOW↑
tAS
tBALE
6
10
ns
6
10
ns
th1
th2
Hold time, data (D7-D0) valid after IOW↑
tDH
tAH
6
5
ns
6
5
ns
td4
td5
Delay time, address (A15-A0) valid to IOCSn↓
tIOCSf
tIOCSr
5
18
ns
5
14
ns
td6
td7
Delay time, address (A23-A0) valid to MCSn↓
tMCSf
tMCSr
6
18
ns
6
14
ns
td8
td9
Delay time, IOR↓ to OENn↓
tOENf
tOENr
5
15
ns
10
ns
25
ns
Setup time, data (D7-D0) valid before IOW↑
Setup time, address (A23-A0) valid before BALE↓
Hold time, address (A15-A0) valid after IOW↑
Delay time, address (A15-A0) invalid to IOCSn↑
Delay time, address (A23-A0) invalid to MCSn↑
Delay time, IOR↑ to OENn↑
5
After 2-1/2
clock
periods
td10
Delay time, IOR↓ to data (D7-D0) valid
tVD
5
td11
td12
Delay time, IOR↑ to data (D7-D0) floating
tHZD
tIRQr
5
20
ns
7
12
ns
td13
td14
Delay time, INTRn↓ to IRQm↓
tIRQf
tDRQr
7
14
ns
8
9
ns
td15
td16
Delay time, DMA_RQn↓ to CDRQm↓
8
10
ns
Delay time, CDACKm↓ to DMA_ACKn↓
tDRQf
tDACKf
8
16
ns
td17
Delay time, CDACKm↑ to DMA_ACKn↑
tDACKr
8
12
ns
Delay time, INTRn↑ to IRQm↑
Delay time, DMA_RQn↑ to CDRQm↑
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
11
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
APPLICATION INFORMATION
MEMW
MEMR
IOW
Logical
Device #1
IOR
DATA
ADDRESS
(see Note C)
(see Note B)
RESET DRV
MEMW
MEMR
IOW
Logical
Device #0
IOR
DATA
ADDRESS
(see Note C)
BALE
LA23−LA17
SA16−SA0
D7−D0
7
17
8
DMA_ACK1
INTR1
DMA_RQ1
MCS1
IOCS1
DMA_ACK0
INTR0
DMA_RQ0
MCS0
(see Note D)
OEN0
ISA Bus
IOCS0
(see Note B)
RESET DRV
SROM_BUSY
PNP_BUSY
IOR
IOW
To Optional
On-Board
Controller
RESETDRV
TL16PNP200
AEN
IRQ3−15
DRQ0, 3, 5
DACK0, 3, 5
11
3
3
SCLK
(see Note A)
(see Note A)
SCS
SIO
C
S
Serial
D EEPROM
2 kΩ
Q
OSC
NOTES: A.
B.
C.
D.
CLK
Any three DMA channels can be used.
Number of address lines depends on the programmed I/O and memory block sizes.
Number of data lines is logical device dependent.
OEN0 can be used with either logical device.
Figure 2. TL16PNP200 Application − Mode 0
12
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
APPLICATION INFORMATION
Logical
Device #4
Data, Address, Control
Logical
Device #3
Data, Address, Control
Logical
Device #2
Data, Address, Control
16
INTR4
IOCS4
IOCS3
INTR3
INTR2
IOCS2
(see Note B)
OEN1
INTR1
DMA_RQ1
(see Note B)
OEN0
IOCS1
DMA_ACK0
IOCS0
ISA Bus
SA15−SA0
D7−D0
INTR0
DMA_RQ0
Logical
Device #0
Data, Address, Control
DMA_ACK1
Logical
Device #1
Data, Address, Control
SROM_BUSY
8
PNP_BUSY
IOR
IOW
To Optional
On-Board
Controller
RESETDRV
AEN
IRQ3−7, 9−12, 14−15 11
DRQ0,1, 3, 5, 6 5
DACK0, 1, 3, 5, 6 5
TL16PNP200
SCLK
(see Note A)
(see Note A)
SCS
SIO
C
S
Serial
D EEPROM
2 kΩ
Q
NOTES: A. Any five DMA channels can be used.
B. OEN0 and OEN1 can be used with any two logical devices.
Figure 3. Typical Application − Mode 1
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
13
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
APPLICATION INFORMATION
on-board EEPROM programming
This section describes a simple approach to programming the resource EEPROM in an expansion board that
uses the TL16PNP200. This approach involves utilizing a readily available standard EEPROM programmer and
a ribbon cable in addition to minor additions to the expansion board.
A connector is needed on the expansion board to provide access to the EEPROM signals as shown in Figure
4. Two jumper wires are used to isolate the EEPROM during programming. Power to the board must be removed
before programming. To isolate the VCC of the EEPROM from the board VCC, Jumper 2 should be disconnected.
This disables the PnP controller and prevents it from driving the EEPROM inputs. Jumper 1 should also be taken
off during programming to isolate the D input and Q output. The PnP controller uses a single pin for the EEPROM
data input and output.
The ribbon cable plugs into the on-board connector on one end, and the other end has a DIP connector that
plugs into the EEPROM programmer.
Programming the EEPROM is achieved by connecting the unpowered board to the programmer using the
ribbon cable, removing the jumper wires, and then using the software supplied with the programmer. After
programming is complete, the jumper wires are reattached and the board is now ready for testing.
hardware required for programming an expansion board EEPROM
The hardware required for programming an expansion board EEPROM is listed in the following bulleted list and
shown in Figure 4.
D EEPROM programmer
D Ribbon cable with connectors
D On-board connector and two jumper wires
TL16PNP200
EEPROM
SCLK
C
SCS
S
D
SIO
Q
R1
Jumper 1
Jumper 2
VCC
DU
ORG
VSS
Connector
Figure 4. Programming an Expansion Board EEPROM
14
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
VCC
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PARAMETER MEASUREMENT INFORMATION
CLK
A15−A0
Valid Address
td4
td5
IOCSn
tw2
IOR
td8
td9
OENm
td10
td11
Valid Data
D7−D0
Figure 5. Read Cycle and I/O Chip Select Timing
A23−A0
Valid Address
tsu3
BALE
td6
td7
MCSn
tsu2
th2
tw1
IOW
tsu1
th1
Valid Data
D7−D0
Figure 6. Write Cycle and Memory Chip Select Timing
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
15
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PARAMETER MEASUREMENT INFORMATION
INTRn
td12
td13
IRQm
Figure 7. Interrupt Timing
DMA_RQn
td14
td15
CDRQm
CDACKm
td16
DMA_ACKn
Figure 8. DMA Signal Timing
16
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
td17
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PRINCIPLES OF OPERATION
PnP card configuration sequence
The PnP logic is quiescent on power up and must be enabled by software.
1. The initiation key places the PnP logic into configuration mode through a series of predefined writes to
the ADDRESS port (see autoconfiguration ports section).
2. A serial identifier is accessed in bit-sequence and used to isolate the ISA cards. Seventy-two
READ_DATA port reads are required to isolate each card.
3. Once isolated, a card is assigned a CSN that is later used to select the card. This assignment is
accomplished by programming the CSN register.
4. The PnP software then reads the resource-data structure on each card. When all resource capabilities
and demands are known, a process of resource arbitration is invoked to determine resource allocation
for each card.
5. All PnP cards are then activated and removed from the configuration mode. This activation is
accomplished by programming the ACTIVE register.
PnP autoconfiguration ports
Three 8-bit ports (see Table 5) are used by the software to access the configuration space on each PnP ISA
card. These registers are used by the PnP software to issue commands, check status, access the resource data
information, and configure the PnP hardware.
The ports have been chosen so as to avoid conflicts in the installed base of ISA functions, while at the same
time minimizing the number of ports needed in the ISA I/O space.
Table 5. Autoconfiguration Ports
PORT NAME
ADDRESS
LOCATION
0×0279 (printer status port)
TYPE
Write only
WRITE_DATA
0×0A79 (printer status port + 0×0800)
Write only
READ_DATA
Relocatable in range 0×0203 to 0×03FF
Read only
The PnP registers are accessed by first writing the address of the desired register to the ADDRESS port,
followed by a read of data from the READ_DATA port or a write of data to the WRITE_DATA port. Once
addressed, the desired register may be accessed multiple times through the WRITE_DATA or READ_DATA
ports.
The ADDRESS port is also the destination of the initiation key writes (see PnP ISA specification).
The address of the READ_DATA port is set by programming the SET RD_DATA PORT register. When a card
cannot be isolated for a given READ_DATA port address, the READ_DATA port address is in conflict. The
READ_DATA port address must then be relocated and the isolation process begun again. The entire range
between 0×0203 and 0×3FF is available; however, in practice it is expected that only a few address locations
are necessary before the software determines that PnP cards are not present.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
17
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PRINCIPLES OF OPERATION
PnP registers
PnP card standard registers are divided into three parts: card control, logical device control, and logical device
configuration. There is one of each card control register on each ISA card. Card control registers are used for
global functions that control the entire card. Logical device control registers and logical device configuration
registers are repeated for each logical device. All unimplemented configuration registers are reset to 0 when
read.
PnP card control registers
The PnP card control registers are listed in Table 6. All registers are cleared to 0 on power-up.
Table 6. PnP Card Control Registers
ADDRESS PORT
0×00
REGISTER NAME
SET RD_DATA PORT
ACCESSIBILITY
Write only
Writing to this register modifies the address port used for reading from the PnP ISA card. Writing to this register is only
allowed when the card is in the isolation state.
Bit [7-0]
These bits become I/O port address bits 9-2.
0×01
SERIAL ISOLATION
Read only
Reading from this register causes a card in the isolation state to compare one bit of the board ID.
0×02
CONFIGURATION CONTROL
Write only
This 3-bit register consists of three independent commands, which are activated by writing a 1 to their corresponding
register bits. These bits are automatically reset to 0 by the hardware after the commands execute.
Bit [2]
Writing a 1 to this bit causes the card to reset its CSN and RD-DATA port to zero.
Bit [1]
Writing a 1 to this bit causes the card to enter the wait-for-key state, but the card CSN is
preserved and the logical device is unaffected.
Bit [0]
Writing a 1 to this bit resets the logical device’s configuration registers to their default state, and the CSN
is preserved.
0×03
WAKE[CSN]
Write only
Writing to this register, when the write data [7-0] matches the card CSN, causes the card to go from the sleep state either
to the isolation state when the write data for this command is zero, or to the configuration state when the write data is not
zero. The pointer to the SERIAL IDENTIFIER is reset. This register is write only.
0×04
RESOURCE DATA
Read only
Reading from this register reads the next byte of resource information from the EEPROM. The STATUS register must be
polled until its bit 0 is set before this register may be read.
0×05
STATUS
Bit [0]
0×06
Read only
A one-bit register that, when set, indicates that it is okay to read the next data byte from the
RESOURCE DATA register.
CARD-SELECT NUMBER
Read/write
Writing to this register sets the CSN of a card, which is uniquely assigned to a card after the serial identification process.
This allows each card to be individually selected during a Wake[CSN] command.
0×07
LOGICAL DEVICE NUMBER
Read/write
This register specifies which logical device is being configured.
18
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PRINCIPLES OF OPERATION
PnP logical device control registers
The registers in Table 7 are repeated for each logical device. These registers control device functions, such as
enabling the device onto the ISA bus.
Table 7. PnP Logical Device Control Registers
ADDRESS PORT
0×30
REGISTER NAME
ACTIVE
ACCESSIBILITY
Read/write
This register controls whether the logical device is active on the bus.
Bit [7-1]
These bits are reserved and must be set to 0.
Bit [0]
If set, this bit activates the logical device.
An inactive device does not respond to nor drive any ISA bus signals. Before a logical device is activated, I/O range check
must be disabled.
0×31
I/O RANGE CHECK
Read/write
This register is used to perform a conflict check on the I/O port range programmed for use by the logical device.
Bit [7-2]
This bit is reserved and must be set to 0.
Bit [1]
If bit is set, the I/O range check is enabled. I/O range check is only valid when the logical device is
inactive.
Bit [0]
If bit 0 is set, the logical device responds to I/O and reads to its assigned I/O range with a 0×55.
If bit 0 is clear, the logical device responds with a 0×AA.
PnP logical device configuration registers
The registers in Table 8 program the device ISA bus resource use and are repeated for each logical device.
Registers in the ISA PnP specification that are not implemented in the TL16PNP200 are reset to 0 when read,
except for the unimplemented DMA channel select descriptor 1 (0x75) which returns a 4 when read.
Table 8. PnP Logical Device Configuration Registers
ADDRESS PORT
0×40
REGISTER NAME
MEMORY BASE ADDRESS [23-16]
ACCESSIBILITY
Read/write
This register indicates the selected memory base address of bits 23-16.
0×41
MEMORY BASE ADDRESS [15-8]
Read/write
This register indicates the selected memory base address of bits 15-8.
0×42
MEMORY CONTROL
Read/write
Bit 1 specifies 8 by 16-bit control. When set bit 1 indicates 16-bit memory, and cleared to indicate 8-bit memory.
Bit 0 is read-only. It is internally set to 1 indicating that the next field is the upper limit for the address. TL16PNP200 supports
memory upper limit, not range length.
0×43
MEMORY UPPER LIMIT ADDRESS [23−16]
Read/write
This register indicates the selected memory upper limit address of bits 23-16.
0×44
MEMORY UPPER LIMIT ADDRESS [15-8]
Read/write
This register indicates the selected memory upper limit address of bits 15-8.
0×60
I/O PORT BASE ADDRESS [15-8]
Read/write
This register indicates bits 15-8 of the base address that are to be used for the selected I/O address range.
0×61
I/O PORT BASE ADDRESS [7-0]
Read/write
This register indicates bits 7-0 of the base address that are to be used for the selected I/O address range.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
19
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PRINCIPLES OF OPERATION
Table 9. PnP Logical Device Configuration Registers (continued)
ADDRESS PORT
0×70
REGISTER NAME
ACCESSIBILITY
INTERRUPT REQUEST LEVEL SELECT
Read/write
This register indicates the selected interrupt level. Bits [3-0] select which interrupt level is used. The TL16PNP200 supports
all 11 interrupts available on the ISA bus.
0×71
INTERRUPT REQUEST TYPE SELECT
Read/write
This register indicates which type of interrupt is used for the selected IRQ.
Bit[1] : Level,
1 = high, 0 = low
Bit[0] : Type,
1 = level, 0 = edge
Note that at the IRQ outputs of the TL16PNP200, the interrupt type is the same as the type at the INTR inputs, regardless
of the programmed type.
0×74
DMA CHANNEL SELECT
Read/write
This register indicates the selected DMA channel. Bits 2-0 select which DMA channel is in use: 000 selects DMA
channel 0, 111 select DMA channel 7. DMA channel 4, the cascade channel indicates no DMA channel is active. The
TL16PNP200 supports three DMA channels to select from in Mode 0 and five in Mode 1. The DMA mapping register, loaded
on power-up, tells the device which DMA channels are connected to it (see the defaults description section).
EEPROM
The TL16PNP200 interfaces to the SGS Thomson EEPROM ST93C56/66 or an equivalent. The EEPROM
provides the PnP resource data and power-up defaults.
memory organization
The EEPROM should be organized as 128/255 words multiplied by 16 bits, therefore, its ORG terminal should
be connected to VCC or left unconnected. The memory organization for the EEPROM is shown in Table 10.
Table 10. EEPROM Memory Organization
EEPROM
LOCATION
15
14
13
12
11
10
BIT LOCATION
9
8 7
6
5
4
3
2
1
0
0
Power-up Defaults
13
14
PnP Resource Data
128/255
EEPROM READ (see Figure 9 and 10)
This device only supports read transactions. The READ op code instruction (10) must be sent into the EEPROM.
The op code is then followed by an 8-bit-long address for the 16-bit word. The READ op code with accompanying
address directs the EEPROM to output serial data on the EEPROM data terminals D and Q, which is connected
to the TL16PNP200 bidirectional serial data bus (SIO). Specifically, when a READ op code and address are
received, the instruction and address are decoded and the addressed EEPROM data is transferred into an
output shift register in the EEPROM. Each read transaction consists of a start bit, 2-bit op code (10), 8-bit
address, and 16-bit data. The TL16PNP200 does not accommodate the auto-address next word feature of the
EEPROM.
20
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
PRINCIPLES OF OPERATION
READ op code transfer (see Figure 9)
Initially, the chip select signal,S, of the EEPROM, which connects to the TL16PNP200 EEPROM chip select
(SCS), is raised. The data D and Q of the EEPROM then sample the TL16PNP200 (SIO) line on the following
rising edges of the TL16PNP200 clock SCLK, until a 1 is sampled and decoded by the EEPROM as a start bit.
The SCLK signal of the TL16PNP200 connects to the EEPROM clock C. The READ op code (10) is then
sampled on the next two rising edges of SCLK. The TL16PNP200 sources the op code at the falling edges of
SCLK.
tw(SCLKH)
C
(SCLK)
tw(SCLKL)
td1
S
(SCS)
tpd1
td2
D/Q
(SIO)
Start
Op Code Input = 1
Start
Op Code Input = 0
Op Code Input
NOTE A: The corresponding TL16PNP200 terminal names are provided in parentheses. D/Q indicates that D and Q terminals in the EEPROMs
are tied together with a 2-kΩ resistor.
Figure 9. READ Op Code Transfer
READ address and data transfer (see Figure 10)
After receiving the READ op code, the EEPROM samples the READ address on the next eight rising edges of
SCLK. The device sources the address at the falling edge of SCLK. The EEPROM then sends out a dummy
bit 0 on the D/Q line, which is followed by the 16-bit data word with the MSB first. Output data changes are
triggered by the rising edges of SCLK. The data is also read by the TL16PNP200 on the rising edges of SCLK.
C
(SCLK)
tpd3
S
(SCS)
td2
tpd1
tpd2
td3
D/Q
(SIO)
Address Input
Data Output
NOTE A: The corresponding TL16PNP200 terminal names are provided in parentheses. D/Q indicates that D and Q terminals in the EEPROMs
are tied together with a 2-kΩ resistor.
Figure 10. READ Address and Data Transfer
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
21
SLLS229A − NOVEMBER 1995 − REVISED APRIL 1996
MECHANICAL INFORMATION
PH (R-PQFP-G80)
PLASTIC QUAD FLATPACK
0,45
0,25
0,80
64
0,16 M
41
65
40
12,00 TYP
80
14,20
13,80
18,00
17,20
25
1
24
0,15 NOM
18,40 TYP
20,20
19,80
24,00
23,20
Gage Plane
0,25
0,10 MIN
0°−ā 10°
2,70 TYP
1,10
0,70
Seating Plane
3,10 MAX
0,10
4040011 / B 10/94
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
22
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated