ATC Millimeter Wavelength Single Layer Capacitors • Ultra-High Qs • Low Cost • DC to 50 GHz • Broadband Applications • .06 pF to 4700 pF • Not Static Sensitive • Capacitor Arrays • High Reliability Testing • Custom sizes, values, shapes, tolerances and higher voltages ATC 111 SERIES MICROCAP ® capacitors have beveled edges to minimize the potential for crack propagation due to mechanical or thermal shock by eliminating abrupt metal-to-ceramic interfaces. Longer arc-over paths help reduce shorting during epoxy die attachment. ATC 116 SERIES MICROCAP ® capacitors have a conventional straight-sided design which allows the user the ability to match stripline widths or design a custom capacitor for limited circuit dimensions. ATC 112 SERIES BI-TRIM ® capacitors are Binary capacitors in 1:2:2:4 or 1:2:4:8 configurations. This arrangement permits adjustment (trimming) of the capacity value to a desired value by connecting sections in parallel. This is a highly stable variable capacitor with none of the drawbacks of mechanically variable capacitors such as contact resistance, shock and vibration sensitivity. ATC 113 SERIES TWIN/CAP ® capacitors are two capacitors on one substrate that are useful in microstrip lines to minimize lead inductance in coupling applications for frequencies as high as 50 GHz. The coupling without appreciable inductance is achieved by utilizing the two capacitors in series. The unique configuration, low-profile and low inductance TWIN/CAPS® provide low insertion loss and extremely high resonant frequencies. Let ATC assist in designing your custom component. Microcaps® are carried in selected values through our CALL 631-622-4700. QUIK-PICK 48 HOUR SHIPMENT SYSTEM ®. one norden lane, huntington station, n.y. 11746-2142 usa phone: 631-622-4700 • fax: 631-622-4748 • e-mail: [email protected] http://www.atceramics.com ATC # 001-857 Rev. D; 4/00 ATC Single Layer Capacitors: General Specifications ELECTRICAL CHARACTERISTICS ENVIRONMENTAL CHARACTERISTICS, cont. OPERATING FREQUENCY: Up to 50 GHz. These include the following Hi-Rel tests in accordance with MIL-STD-202: RESONANT FREQUENCY: See curve below. • Immersion (method 104, MIL-STD-202) • Resistance to soldering heat (method 210, MIL-STD-202) • Low voltage humidity (MIL-C-49464) • Moisture resistance (method 106) • Life test at +125°C and 2X rated voltage (method 108, test cond. F) • Solderability (method 208) • Voltage conditioning at +125°C and 2X rated voltage (method 108, test cond. A) STANDARD MEASUREMENT FREQUENCY: 1 MHz for .06 to 100 pF; 1 KHz for values greater than 100 pF. INSULATION RESISTANCE: 1011 ohms min. at +25°C and rated voltage. VOLTAGE RATING: 100 WVDC. Consult factory for higher ratings. DIELECTRIC TEST VOLTAGE: 250% of voltage rating for 5 seconds. Impervious to static discharge failures. MECHANICAL CHARACTERISTICS QUALITY PROGRAM HERMETICITY: The dielectric is virtually unaffected by moisture Stringent process procedures and exacting material requirements ensure that only the highest quality parts are shipped. and commonly used cleaning solvents. RUGGED CONSTRUCTION to minimize bonding problems and ATC's manufacturing and Quality Testing facilities comply with the following specifications: circuit assembly problems. • ISO 10012-1 Quality Assurance for Measuring Equipment • ANSI / NCSL Z540-1-1994 Calibration Laboratories and Measuring and Test Equipment - General Requirements BOND STRENGTH: All terminations meet or exceed MIL-STD-883 Method 2019 for Die shear strength. Wire bondability meets or exceeds MIL-C-49464 Paragraph 3.12 as well as MIL-STD-883 Method 2011. ENVIRONMENTAL CHARACTERISTICS OPERATING TEMPERATURE: –55°C to +125°C. (No derating of working voltage) ATC parallel plate capacitors are designed and manufactured to meet or exceed the requirements of MIL-C-49464. SERIES RESONANCE VS CAPACITANCE FREQUENCY (GHz) 1000 100 10 1 Typical 0.1 0.1 1 10 CAPACITANCE 2 100 1000 10000 (pF) American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com ATC Single Layer Capacitors: Dielectric Specifications Ultra Stable Capacitors for Filtering and Tuning Applications - Stable K Dielectric Dielectric Code T.C. (–55°C to +125°C) Dielectric Const. (K) Min. Q @ 1 MHz Max. DF @ 1 MHz (%) A +90 ±30 PPM/°C 14 10,000 0.01 AX 0 ±30 PPM/°C 23 2,000 0.05 BA –80 ±30 PPM/°C 36 660 0.15 BB 0 ±30 PPM/°C 31 660 0.15 CA 0 ±30 PPM/°C 62 660 0.15 CC –750 ±200 PPM/°C 130 660 0.15 Broadband Applications Including Coupling and Decoupling - Mid K Dielectric Dielectric Code T.C. (–55°C to +125°C) Dielectric Const. (K) Min. Q @ 1 MHz DF @ * 1Max. KHz (%) DA –1500 ±500 PPM/°C 165 400 N/A DB ±7.5% max. change (non-linear) 200 400 N/A HC –2000 ±500 PPM/°C 350 200 0.3 EA –4700 ±1500 PPM/°C 650 400 0.3 EC ±10% max. change (non-linear) 650 65 1.5 Higher Capacitance Value, For By-Pass and DC Blocking Applications - High K Dielectric Dielectric Code T.C. (–55°C to +125°C) Dielectric Const. (K) Min. Q @ 1 MHz DF @ * 1Max. KHz (%) J +5% to –15% max. change (non-linear) 1100 40 2.0 F ±10% max. change (non-linear) 2000 40 2.0 G +10% to –75% max. change (non-linear) 4500 40 2.0 K 0% to –92% max. change (non-linear) 9000 25 2.0 * Applies to values greater than 100 pF. American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com 3 ATC Single Layer Millimeter Wavelength Microcaps ®: 111 & 116 Series ATC PART NUMBER CODE 111 S CA 0R5 B 100 T T Termination Suffix Series: 111 Beveled edges 116 Perpendicular edges Code Description Thin Film: Titanium Tungsten / Nickel /Gold (Standard) 100 µ in. min. Gold TT Case Size: See Mechanical Configurations; page 5. AP Dielectric Style: Max. 2 characters, see Specification Chart; page 3. Thick Film: Platinum Gold 300 µ in. min. WVDC (in Volts): 3 significant digits, 100 Volts is standard. Capacitance Code: 2 significant digits, R = Decimal point; Number of zeros following significant digits. See pages 6 and 7 for capacitance values. Capacitance Tolerance Code A (pF) B (pF) C (pF) D (pF) F (%) G (%) J (%) K (%) M (%) Tol. ± 0.05 ± 0.1 ± 0.25 ± 0.5 ±1 ± 2% ±5 ± 10 ±20% Use the Standard Capacitance Value chart on pages 6 and 7 to select a code which is within the capacity range given for a specific case size/dielectric combination. Select a capacitance tolerance from the available tolerances listed in the Selection Chart. The above part number describes a 100 volt, T T termination (thin film), 111 series (beveled edge) capacitor, case size S (0.018" square nominal), CA dielectric (0 ±30 ppm/°C). This size/dielectric combination has a capacitance range of 0.4 to 0.9 pF and available tolerances of B, C or D. 0R5 defines a capacitance value of 0.5 pF. B tolerance (±0.1 pF) was selected. ATC accepts orders for our parts using designations with or without the “ATC” prefix. Both methods of defining the part number are equivalent, i.e., part numbers referenced with the “ATC” prefix are interchangeable to parts referenced without the “ATC” prefix. Customers are free to use either in specifying or procuring parts from American Technical Ceramics. Design Your Own Single Layer Capacitor ATC gives you the ability to create custom values and dimensions. When circuit board area is tight or you need to match your stripline width, you can optimize the size and shape of required SLCs. This same technique can be used to build special values that fall outside of the standard offerings. Custom Values and Sizes Optimize the best combination of length, width, thickness and dielectric material for your circuit/stripline capacitor requirements. L = Length 10 to 100 mils ATC SLC T = Thickness 4 to 12 mils W = Width 10 to 100 mils Dielectric Constant (K) Design Guidelines 4 C = Capacitance (pF) C = (.225 K x L x W) / (1000 T) L = Length 10 to 100 mils, may not exceed 20 x T or 2.5 x W W = Width 10 to 100 mils, may not exceed 20 x T T = Thickness 4 to 12 mils, less than or equal to L/2 or W/2 A 14 CC 130 EC 650 AX 23 DA 165 J 1100 BA 36 DB 200 F 2000 BB 31 HC 350 G 4500 CA 62 EA 650 K 9000 American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com ATC Single Layer Millimeter Wavelength Microcaps ®: 111 & 116 Series MECHANICAL CONFIGURATIONS - Inches (mm) Case Code W or L Ref. W1 or L1 T* R** .015 (.381) ± .003 (.076) N/A S .018 (.457) ± .003 (.076) .014 (.356) T .025 (.635) ± .005 (.127) U .035 (.889) ± .005 (.127) X .050 (1.27) ± .010 (.254) Y .070 (1.78) ± .010 (.254) .065 (1.65) Z .090 (2.29) ± .010 (.254) .085 (2.16) Q .019 (.483) .003 (.076) min. to .012 (.305) max. .030 (.762) .045 (1.14) Customer specified non-standard dimensions *T depends upon capacity value. **Case size R is not available in 111 Series. 111 SERIES MICROCAPS ® Termination Area L1 Ref L 116 SERIES MICROCAPS ® Termination Area L W1 Ref T W T W NOTES: American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com 5 ATC 111 & 116 Series Microcaps ®: Capacitance Selection Chart Case Size LxW Case Size LxW Case Size LxW Case Size LxW R .015 x .015 (.381 x .381) S .018 x .018 (.457 x .457) T .025 x .025 (.635 x .635) U .035 x .035 (.889 x .889) Dielectric Code Min. (pF) Max. (pF) Tol. Min. (pF) Max. (pF) Tol. Min. (pF) Max. (pF) Tol. Min. (pF) Max. (pF) Tol. A 0.06 0.10 A, B 0.09 0.2 A, B, C 0.2 0.4 A, B, C, D 0.3 0.8 A, B, C, D AX 0.1 0.3 A, B, C 0.2 0.3 A, B, C 0.3 0.7 A, B, C, D 0.6 1.5 B, C, D BA 0.2 0.5 A, B, C, D 0.3 0.5 A, B, C, D 0.4 1.0 B, C, D 0.9 2.2 B, C, D BB 0.2 0.4 A, B, C, D 0.2 0.4 A, B, C, D 0.4 0.9 B, C, D 0.8 1.8 B, C, D CA 0.3 0.7 A, B, C, D 0.4 0.9 B, C, D 0.8 1.8 B, C, D 1.5 3.6 B, C, D CC 0.6 1.5 B, C, D 0.8 1.8 B, C, D 1.6 3.6 C,D 3.3 4.3 4.3 7.5 B, C, D C,D DA 0.7 2.0 C, D 1.0 2.4 C, D 2.0 4.7 C, D 3.9 9.1 C, D DB 0.9 2.4 C, D 1.2 2.7 C, D 2.4 5.6 C, D HC 1.5 3.9 D 2.0 4.3 D 3.9 9.1 D 5.1 9.1 8.2 12 9.1 12 12 22 C, D J, K, M D J, K, M EA 2.7 7.5 D 3.9 9.1 D 8.2 18 J, K, M 15 39 K, M EC 2.7 7.5 D 3.9 9.1 D 8.2 18 J, K, M 15 39 K, M J 5.1 9.1 9.1 12 D K, M 6.8 10 10 15 D K, M 15 27 K, M 27 68 K, M F 9.1 22 K, M 12 27 K, M 22 56 K, M 47 120 K, M G 22 56 M 27 68 M 56 120 M 120 270 M K 47 82 M 68 120 M 120 270 M 220 560 M Inches (mm) Standard Capacity Values 6 CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) R06 R07 R08 R09 0R1 0R2 0.06 0.07 0.08 0.09 0.1 0.2 0R3 0R4 0R5 0R6 0R7 0R8 0.3 0.4 0.5 0.6 0.7 0.8 0R9 1R0 1R1 1R2 1R3 1R5 0.9 1.0 1.1 1.2 1.3 1.5 1R6 1R8 2R0 2R2 2R4 2R7 1.6 1.8 2.0 2.2 2.4 2.7 3R0 3R3 3R6 3R9 4R3 5R1 3.0 3.3 3.6 3.9 4.3 5.1 5R6 6R2 6R8 7R5 8R2 9R1 5.6 6.2 6.8 7.5 8.2 9.1 American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com ATC 111 & 116 Series Microcaps ®: Capacitance Selection Chart Case Size LxW Case Size LxW Case Size LxW X .050 x .050 (1.27 x 1.27) Y .070 x .070 (1.78 x 1.78) Z .090 x .090 (2.29 x 2.29) Min. (pF) Max. (pF) Tol. Min. (pF) Max. (pF) Tol. Min. (pF) Max. (pF) Tol. Dielectric Code 0.7 1.8 B, C, D 1.3 3.6 B, C, D 2.2 5.6 B, C, D A 1.1 3.0 B, C, D 2.2 5.6 B, C, D 3.6 10 B, C, D AX 1.8 4.3 B, C, D 3.6 7.5 7.5 9.1 B, C, D C, D BA 3.9 B, C, D 3.0 6.8 B, C, D 9.1 15 9.1 12.0 B, C, D F, G, J, K, M 1.5 5.6 9.1 5.6 9.1 B, C, D F, G, J, K, M BB 3.3 7.5 C, D 6.8 10 10 15 C, D G, J, K, M 10 27 F, G, J, K, M CA 6.8 9.1 8.2 10 9.1 15 10 22 C, D G, J, K, M D, J, K, M J, K, M 15 33 G, J, K, M 22 56 F, G, J, K, M CC 18 39 G, J, K, M 27 68 G, J, K, M DA 10 22 J, K, M 22 47 G, J, K, M 33 82 G, J, K, M DB 18 39 J, K, M 33 82 J, K, M 56 150 J, K, M HC 33 82 K, M 56 150 J, K, M 100 270 J, K, M EA 33 82 K, M 56 150 J, K, M 100 270 J, K, M EC 68 150 K, M 120 270 K, M 180 470 K, M J 100 270 K, M 220 470 K, M 330 820 M F 220 560 M 470 1000 M 820 2200 M G 470 1200 M 1000 2200 M 1500 4700 M K Inches (mm) Standard Capacity Values CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) CAP. CODE CAP. (pF) 100 120 150 180 220 270 10 12 15 18 22 27 330 390 470 560 680 820 33 39 47 56 68 82 101 121 151 181 221 271 100 120 150 180 220 270 331 391 471 561 681 821 330 390 470 560 680 820 102 122 152 182 222 272 1000 1200 1500 1800 2200 2700 332 392 472 3300 3900 4700 Special values, sizes and tolerances available upon request. Consult factory. American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com 7 112 Series BI-TRIM ® Binary Capacitors CONFIGURATION 4 CONFIGURATION 3 Total Cap. (pF) C1 Tol. (pF) C2 Tol. (pF) C4 Tol. (pF) 112M3A0R9C100TT 0.9 0.1 B 0.2 B 0.4 C 112M3CA2R7C100TT 2.7 0.3 B 0.6 C 112N3CA9R0D100TT 9.0 1.0 C 112N3DB270M100TT 27 112M3F900M100TT 90 Part Number Total Cap. (pF) C1 Tol. (pF) C2 Tol. (pF) C4 Tol. (pF) C8 Tol. (pF) 112P4A1R5C100TT 1.5 0.1 B 0.2 B 0.4 B 0.8 C 1.2 C 112P4CA4R5D100TT 4.5 0.3 C 0.6 C 1.2 C 2.4 D 2.0 C 4.0 D 112P4DB150M100TT 15 1.0 M 2.0 M 4.0 M 8.0 M 3.0 M 6.0 M 12 M 112P4EC450M100TT 45 3.0 M 6.0 M 12 M 24 M 10 M 20 M 40 M 112R4J151M100TT 150 10 M 20 M 40 M 80 M Part Number NOTE: Selected values in bold italic type are available from Quik-Pick® – See page 11. CONFIGURATION 3 CONFIGURATION 4 Case Size L=W Inches (mm) L1 = W1 (ref.) L2 = W2 (ref.) Case Size L=W Inches (mm) L1 (ref.) L2 (ref.) W1 (ref.) W2 (ref.) M .050 ±.005 (1.27 ±0.13) .015 (0.38) .030 (0.76) P .060 ±.005 (1.52 ±0.13) .019 (0.48) .038 (0.97) .011 (0.28) .045 (1.14) N .070 ±.005 (1.78 ±0.13) .022 (0.56) .044 (1.12) R .070 ±.005 (1.78 ±0.13) .022 (0.56) .044 (1.12) .013 (0.33) .053 (1.34) T (Thickness): .005 (0.13) min. to .010 (0.25) max. G: .005 nom. T (Thickness): .005 (0.13) min. to .010 (0.25) max. G: .005 nom. CONFIGURATION 3 C1 C2 C1 G C2 C4 CONFIGURATION 4 W1 L1 G W W2 C2 G W1 L1 L2 u G T C4 C8 W2 W L2 u L T L ATC PART NUMBER CODE: 112/113 Series 112 Series: 112 or 113 N 3 CA 9R0 D 100 TT Termination Suffix: TT: Titanium Tungsten/Nickel/Gold Case Size Code Configuration: 112 Series only. Dielectric Style: Max. 2 characters. Available in the following styles: A, CA, CC, DB, HC, EC, J, F, G. See page 3 for T.C. WVDC (in Volts): 3 significant digits, 100 Volts is standard. Capacitance Tolerance Code B (pF) C (pF) D (pF) K (%) M (%) Tol. ±0.1 ±0.25 ±0.5 ±10 ±20 Capacitance Code: 2 significant digits, R = Decimal point; Number of zeros following significant digits. ATC accepts orders for our parts using designations with or without the “ATC” prefix. Both methods of defining the part number are equivalent, i.e., part numbers referenced with the “ATC” prefix are interchangeable to parts referenced without the “ATC” prefix. Customers are free to use either in specifying or procuring parts from American Technical Ceramics. 8 American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com ATC 113 Series TWIN/CAP ® Capacitors MECHANICAL CONFIGURATIONS - Inches (mm) Equivalent Series Cap. = C1 2 C2 = Case Size Width (W) Length (L) Width1 (W1) A .025 ±.003 (.635 ±.076) .040 ±.005 (1.02 ±0.13) .022 (.559) .035 ±.003 (.889 ±.076) .060 ±.005 (1.52 ±0.13) .050 ±.005 (1.27 ±0.13) .080 ±.005 (2.03 ±0.13) 2 B The top terminations of C1 and C2 make direct contact with the microstrip line conductors eliminating the loss due to lead wire connections. C D E F .050 ±.005 (1.27 ±0.13) .055 ±.005 (1.4 ±0.13) .065 ±.005 (1.65 ±0.13) .033 (.838) Length1 (L1) Thickness (T) .015 (.381) .020 (.508) .025 (.635) .005 –.012 (0.13 –0.30) .023 (.584) .035 (.889) .047 (1.19) .027 (.686) G: .005 nom. G TYPICAL MOUNTING CONFIGURATION SLC Land C1 C2 W1 W Land u PC Board Ground Plane G L1 u L1 T L Width .025 (.635) Part Number Width .035 (.889) Equivalent Case Series Cap. Size (pF) / Tol. Part Number Width .050 (1.27) Equivalent Case Series Cap. Size (pF) / Tol. Part Number Equivalent Case Series Cap. Size (pF) / Tol. 113ADB1R0C100TT 1.0 C A 113CCA1R0C100TT 1.0 C C 113FCA1R0C100TT 1.0 C F 113AHC2R2D100TT 2.2 D A 113DDB2R2D100TT 2.2 D D 113FCC2R2D100TT 2.2 D F 113AEC3R3D100TT 3.3 D A 113DHC3R3D100TT 3.3 D D 113FDB3R3D100TT 3.3 D F 113AJ4R7D100TT 4.7 D A 113DHC4R7D100TT 4.7 D D 113EDB4R7D100TT 4.7 D E 113AJ6R8K100TT 6.8 K A 113DEC6R8K100TT 6.8 K D 113EHC6R8K100TT 6.8 K E 113BJ8R2K100TT 8.2 K B 113DEC8R2K100TT 8.2 K D 113EHC8R2K100TT 8.2 K E 113BJ100M100TT 10 M B 113DEC100K100TT 10 K D 113FEC100K100TT 10 K F 113AG220M100TT 22 M A 113DF220M100TT 22 M D 113FJ220M100TT 22 M F 113BG330M100TT 33 M B 113CF330M100TT 33 M C 113EJ330M100TT 33 M E 113BG470M100TT 47 M B 113DG470M100TT 47 M D 113FF470M100TT 47 M F NOTE: Selected values in bold italic type are available from Quik-Pick® – See page 11. American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com 9 Quik-Pick 48 Hr. System ® Shipment For ATC 111 Series Microcaps ® FAX THIS FORM TO ATC AT: 631-622-4748 Name: Phone: Fax: Cust. P.O. #: Bill to: Date: Ship to: Cust. Order #: ATC Order #: Application/Program: (THIS LINE FOR ATC USE ONLY) ORDER ANY OF THE VALUES BELOW IN QUANTITIES UP TO 500 PIECES OR DESIGN YOUR CUSTOM KIT AS DESCRIBED FOR QUIK-PICK 48 HOUR SHIPMENT. 111 SERIES QUIK-PICK PART NUMBERS Part Number Cap. (pF) 111SA0R1B100TT 111SBB0R2B100TT 111TA0R2B100TT 111SBB0R3B100TT 111SCA0R4B100TT 111TBB0R4B100TT 111SCA0R5B100TT 111TBB0R5B100TT 111SCA0R6B100TT 111SCA0R7B100TT 111UA0R7B100TT 111SCC0R9C100TT 111SCC1R0C100TT 111XA1R0B100TT 111TCA1R1C100TT 111TCA1R2C100TT 111TCA1R3C100TT 111SDB1R5D100TT 111UCA1R8C100TT 111SDB2R0D100TT 111UCA2R4D100TT 111XBB2R4C100TT 111SHC3R0D100TT 111TCC3R0D100TT 111TDB3R0D100TT 111UCA3R0D100TT 0.1 0.2 0.2 0.3 0.4 0.4 0.5 0.5 0.6 0.7 0.7 0.9 1.0 1.0 1.1 1.2 1.3 1.5 1.8 2.0 2.4 2.4 3.0 3.0 3.0 3.0 W (mm) .018 .018 .025 .018 .018 .025 .018 .025 .018 .018 .035 .018 .018 .050 .025 .025 .025 .018 .035 .018 .035 .050 .018 .025 .025 .035 .457 .457 .635 .457 .457 .635 .457 .635 .457 .457 .889 .457 .457 1.27 .635 .635 .635 .457 .889 .457 .889 1.27 .457 .635 .635 .889 ✓ Part Number Cap. (pF) 111SEC4R3D100TT 111ZA4R3C100TT 111SEC5R1C100TT 111THC5R1D100TT 111UDB5R1D100TT 111XCA5R1D100TT 111THC5R6D100TT 111SJ100K100TT 111SJ100M100TT 111TEC100M100TT 111YCA100K100TT 111SJ120M100TT 111UHC120M100TT 111XDB120K100TT 111SJ150K100TT 111SJ150M100TT 111TEC150M100TT 111TEC180M100TT 111SF220K100TT 111SF220M100TT 111TJ220K100TT 111TJ220M100TT 111XHC220K100TT 111TF270M100TT 111TJ270M100TT 111TF330M100TT 4.3 4.3 5.1 5.1 5.1 5.1 5.6 10 10 10 10 12 12 12 15 15 15 18 22 22 22 22 22 27 27 33 W (mm) .018 .090 .018 .025 .035 .050 .025 .018 .018 .025 .070 .018 .035 .050 .018 .018 .025 .025 .018 .018 .025 .025 .050 .025 .025 .025 ✓ .457 2.29 .457 .635 .889 1.27 .635 .457 .457 .635 1.78 .457 .889 1.27 .457 .457 .635 .635 .457 .457 .635 .635 1.27 .635 .635 .635 Part Number Cap. W (mm) (pF) ✓ 111UEC330K100TT 33 .035 .889 111UEC330M100TT 33 .035 .889 111TF390M100TT 39 .025 .635 111SG470M100TT 47 .018 .457 111TF470K100TT 47 .025 .635 111TF470M100TT 47 .025 .635 111UJ470M100TT 47 .035 .889 111SG560M100TT 56 .018 .457 111UJ560M100TT 56 .018 .457 111TG680M100TT 68 .025 .635 111TG820M100TT 82 .025 .635 111UF820M100TT 82 .035 .889 111TG101M100TT 100 .025 .635 111UF101M100TT 100 .035 .889 111XJ101M100TT 100 .050 1.27 111TG121M100TT 120 .025 .635 111UG221M100TT 220 .035 .889 111XG471M100TT 470 .050 1.27 111YG102M100TT 1000 .070 1.78 111ZG102M100TT 1000 .090 2.29 111ZG182M100TT 1800 .090 2.29 W = Width Inches (mm) KITS Engineering design values you select. Just pick the values from the list above and we will send you 5 pieces each of those values. There are 4 inexpensive kit sizes and all offer the ATC Standard Termination TT (Titanium Tungsten/Nickel/Gold). ❑ 111SL1025 ❑ 111SL1050 10 5 Different Values $60.00 (25 pieces) 10 Different Values $120.00 (50 pieces) ❑ 111SL1075 ❑ 111SL1100 15 Different Values $180.00 (75 pieces) 20 Different Values $240.00 (100 pieces) American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com Quik-Pick 48 Hour System ® Shipment For ATC 112 Series/113 Series FAX THIS FORM TO ATC AT: 631-622-4748 Name: Phone: Fax: Cust. P.O. #: Bill to: Date: Ship to: Cust. Order #: ATC Order #: Application/Program: (THIS LINE FOR ATC USE ONLY) ORDER ANY OF THE VALUES BELOW IN QUANTITIES UP TO 500 PIECES OR DESIGN YOUR CUSTOM KIT AS DESCRIBED FOR QUIK-PICK 48 HOUR SHIPMENT. 112 SERIES QUIK-PICK PART NUMBERS CONFIGURATION 3 Part Number 112M3A0R9C100TT 112M3F900M100TT 112N3CA9R0D100TT CONFIGURATION 4 C1 C2 C4 Total Cap. Val. (pF) 0.1 10 1 0.2 20 2 0.4 40 4 0.9 90 9.0 ✓ C1 C2 C3 C4 Total Cap. Val. (pF) 112P4A1R5C100TT 0.1 112P4DB150M100TT 1 112R4J151M100TT 10 0.2 2 20 0.4 4 40 0.8 8 80 1.5 15 150 Part Number CONFIGURATION 3 C1 C2 CONFIGURATION 4 C1 G C2 W1 L1 G C4 W ✓ u W2 C2 G W1 L2 L1 G T C4 C8 W2 W L2 u L T L 113 SERIES QUIK-PICK PART NUMBERS Part Number Width = .025 ±.003 Equivalent Series Cap. (pF / Tol.) 113ADB1R0C100TT 113AEC3R3D100TT 113BJ8R2K100TT 113BJ100M100TT 113BG330M100TT 1.0 C 3.3 D 8.2 K 10 M 33 M ✓ Part Number Width = .035 ±.003 Equivalent Series Cap. (pF / Tol.) 113CCA1R0C100TT 113DHC3R3D100TT 113DEC8R2K100TT 113DEC100K100TT 113CF330M100TT 1.0 C 3.3 D 8.2 K 10 M 33 M ✓ G C2 Equivalent Series Cap. (pF / Tol.) 113FCA1R0C100TT 113FDB3R3D100TT 113EHC8R2K100TT 113FEC100K100TT 113EJ330M100TT 1.0 C 3.3 D 8.2 K 10 M 33 M ✓ G L1 C1 Part Number Width = .050 ±.003 W1 W u L1 T L KITS Engineering design values you select. Just pick the values from the list above and we will send you 5 pieces each of those values. There are 3 inexpensive kit sizes and all offer the ATC Standard Termination TT (Titanium Tungsten/Nickel/Gold). ❑ 111SL2025 ❑ 111SL2050 5 Different Values $75.00 (25 pieces) 10 Different Values $225.00 (50 pieces) ❑ 111SL2075 15 Different Values $150.00 (75 pieces) American Technical Ceramics • One Norden Lane, Huntington Station, N.Y. 11746-2142 phone: 631-622-4700 • fax: 631-622-4748 • e-mail: sales @ atceramics.com • http://www.atceramics.com 11 one norden lane, huntington station, n.y. 11746-2142 usa phone: 631-622-4700 • fax: 631-622-4748 • e-mail: [email protected] http://www.atceramics.com ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which may result from its use. ATC reserves the right to revise the content or modify its product line without prior notice. © 1997 American Technical Ceramics ATC # 001-857 Rev. D; 4/00