ETC ATPG-L53C

Specification No.
Date
SPECIFICATIONS
5Φ Pure Green LED LAMP
MODEL : ATPG- L53C
Designed by
Checked by
Approved by
ACROSENTEC
2002. 11.20
‰ MODEL : ATPG-L53C
2. Application
1. Features
1-1. InGaN Pure Green Chip
2-1. LED Display / Traffic Guiding signal
1-2. 5mm all epoxy resin mold type
2-2. Illumination device
1-3. Colorless Cylinder type LED lamp
2-3. Back Light for Signboard
1-4. Ultra luminous intensity
3. Dimension
▶Description :
•. 5mm, 30o Water clear type
• Designed for Ultra high brightness
Data subject to change.
‰ MODEL : ATPG-L53C
4. Absolute maximum ratings and Characteristics
4 - 1 Absolute maximum ratings
Ta=25℃
Symbols
Items
Ratings
Units
Forward Current
IF
30
mA
Pulse Forward Current *1
IFP
100
mA
Power Dissipation
PD
78
mW
Reverse Voltage
VR
5
Vr
Operating Temperature
Topr
-30 ~ +85
℃
Storage Temperature
Tstg
-30 ~ +100
℃
Soldering Temperature *2
TSOL
260±5℃
℃
*1) Pulse Width = 100 μsec, Duty ≤ 10%
*2 ) 5sec at location 3.0mm away from the base of the epoxy bulb
4 - 2 Optical and Electrical Characteristics
Item
Symbol
Condition
Ta=25℃
Min
Typ
Max
Unit
Forward Voltage
VF
IF=20[mA]
-
3.4
3.8
V
Reverse Current
IR
VR=5[V]
-
-
10
㎂
Luminous Intensity
IV
IF=20[mA]
-
mcd
Dominant Wavelength
λd
IF=20[mA]
Spectral Linewidth
Δλ
IF=20[mA]
-
nm
Viewing Angle
2Θ1/2
IF=20[mA]
Data subject to change.
4800
6000
525
-
26
30
deg
‰ MODEL : ATPG-L53C
6. Typical Electro-optical characteristics curve
■Forward Voltage vs. Forward Current
100
Forward Current[mA]
Relative Luminous Intensity[a.u.]
■ Lead Temperature vs. Relative Luminosity
1
10
0.1
-20
0
20
40
60
80
1
1.0
100
2.0
Lead Temperature[℃]
4.0
5.0
■Ambient Temperature vs. Forward Current
■ Luminous Spectrum
40
1.2
1.0
30
0.8
Forward Current[mA]
Relative Intensity[a.u.]
3.0
Forward Voltage[V]
0.6
0.4
0.2
0.0
400
450
500
550
600
650
20
10
0
-20
700
0
30
- 30
60
- 60
- 90
1
Data subject to change.
40
0.5
0
60
Ambient Temperature[℃]
0
■ Spatial Distribution
20
0.5
1
90
80
‰ MODEL : ATPG-L53C
7. Inspection Standards
7 - 1 In production line, 100% inspection for electro-optical characteristics should
be done on following 3 items.
- VF , IR , Iv
7 - 2 Outgoing inspection be done to the standards as below.
- MIL-STD-104D, S-3, AQL 1.0%
- Items: VF, IR, Iv, λp
8. Packing Standards
8 – 1.Taping :
Standard taping provided. Or user’s request.
8 – 2 Bulk Packing :
In one vinyl pack, 500 or 1,000 LEDs are inserted. Or user’s request.
9. Caution on usage
9 - 1 Be careful never to exceed , even momentarily, the absolute maximum ratings
specified in the data sheet.
9 - 2 ACROSENTEC will not be held responsible for any damage to the user that
may result from accidents or any other reasons during operation of the user such
as use in excess of the absolute maximum ratings, or not keeping the matters that
demand special attention.
9 - 3 Store and use where there is no corrosive gas.
9 - 4 The bending or cutting of the lead should be done in room temperature and no
force applied on the package.
Data subject to change.
Copyright ⓒ 2003 AcrosenTec Co.,Ltd, (www.AcrosenTec.com)