8/05/02 Series 741, 742, 743, 744, 745, 746 Technical R THICK FILM CHIP RESISTOR ARRAYS * Low cost * High density packaging * Leadless surface mount construction * Tape & reel packaging * Solder coated nickel barrier pads * Isolated and bussed circuits * Convex or Concave Termination Options Chip Array Product Benefits * High Density Packaging Up to 30% less space per resistor than 0603 chip resistors Up to 75% less space per resistor than 0805 chip resistors * Placement Efficiency Networks require fewer placements than discrete components Larger overall size eases handling compared to discrete components * Low Profile Can be used in PCMCIA cards * Perfect solution for DRAM series termination or Pull up/down signal bias. Electrical and Mechanical Specifications Series 741 742 743 744 745 746 PCB Area (in²) Per Resistor .0015 .0037 .0071 .0094 .0058 .0013 Circuit Resistance 70°C Power Type Range Ohms Per Resistor * Isolated Isolated Isolated Isolated Bussed Bussed 10 - 1M 10 - 1M 10 - 1M 10 - 1M 33 - 470K 33 - 100K Resistance Tolerance Standard: ±5% or 0.5 Ohms Whichever is greater Special: ±2% and ±1% * Note: Total Rated Package Power equals total number of resistors times rated Power Per Resistor Maximum Operating Voltage .063W .063W .100W .125W .063W .031W 25V 50V 100V 200V 50V 25V Operating Temperature Range -55°C to +125°C Temperature Coefficient (TCR) Standard ±200ppm/°C CTS CORPORATION / Around The World, Your Single Source For Excellence 8/05/02 Package Outlines Concave Termination -Type C L P Convex Termination -Type X L T P D T C B C B W Termination Area (all places) W A A Pa rt Code # Pads # Res. C ircuit L 741X043 4 2 Isolated 1.0 ±0.1 .039 ±.004 741X083 8 4 Isolated 741C083 8 4 Isolated 741X163 16 8 Isolated 3.8 ±0.1 .150 ±.004 742C043 4 2 Isolated 1.6 ±0.2 .063 ±.008 2.0 ±0.1 .079 ±.004 742X083 742C083 8 4 Isolated 3.2 ±0.2 .126 ±.008 742C163 16 8 Isolated 6.4 ±0.2 .252 ±.008 743C043 4 2 Isolated 2.54 ±0.20 .100 ±.008 743C083 8 4 Isolated 5.08 ±0.3 .200 ±.012 744C043 4 2 Isolated 2.54 ±0.20 .100 ±.008 744C083 8 4 Isolated 5.08 ±0.3 .200 ±.012 745C101 745C102 10 8 Bussed W P T 0.65 ±0.10 .026 ±.004 1.0 ±0.1 .039 ±.004 0.50 ±0.1 .020 ±.004 1.6 ±0.2 .063 ±.008 C D 0.20 ±0.15 .008 ±.006 0.20 ±0.10 .008 ±.004 0.38 Max. .015 Max. 0.30 ±0.1 .012 ±.004 0.30 ±0.1 .012 ±.004 0.28 ±0.1 .011 ±.004 0.45 ±0.10 .020 ±.004 0.8 ±0.05 .032 ±.002 B 0.33 ±0.10 .013 ±.004 0.35 ±0.10 .014 ±.004 1.6 ±0.1 .063 ±.004 A Dimensions: mm inch 0.6 +0.10 -.25 .024+.004 -.010 0.30 ±0.1 .012 ±.004 N /A 0.4 ±0.15 .016 ±.006 0.5 ±0.15 .020 ±.006 0.3 ±0.20 .012 ±.008 0.3 ±0.15 .012 ±.006 N /A 0.4 ±0.15 .016 ±.006 2.0 ±0.2 .079 ±.008 1.27 ±0.05 .050 ±.002 0.6 ±0.1 .024 ±.004 0.8 ±0.15 .031 ±.006 0.4 ±0.2 .016 ±.008 0.4 ±0.15 .016 ±.006 N /A 3.2 ±0.2 .126 ±.008 1.27 ±0.05 .050 ±.002 0.6 ±0.1 .024 ±.004 0.9 ±0.15 .035 ±.006 0.5 ±0.2 .020 ±.008 0.5 ±0.15 .020 ±.006 N /A 6.4 ±0.2 .252 ±.008 3.2 ±0.2 .126 ±.008 1.27 ±0.05 .050 ±.002 0.6 ±0.1 .024 ±.004 0.6 ±0.15 .024 ±.006 0.35 ±0.15 .013 ±.006 0.55 ±0.15 .022 ±.006 N /A 3.2 ±0.2 .126 ±.008 1.27 ±0.05 .050 ±.002 0.6 ±0.1 .024 ±.004 0.9 ±0.15 .035 ±.006 0.5 ±0.2 .020 ±.008 0.5 ±0.15 .020 ±.006 1.1 ±0.15 .043 ±.006 1.65 ±0.15 .065 ±.006 .64 ±0.05 .025 ±.002 0.6 ±0.1 .024 ±.004 0.35 ±0.05 .014 ±.002 0.4 ±0.10 .016 ±.004 0.45 ±0.10 .018 ±.004 0.5 ±0.05 .020 ±.002 745X101 745X102 10 8 Bussed 6.4 ±0.2 .252 ±.008 746X101 10 8 Bussed 3.3 ±0.1 .130 ±.004 Recommended Land Patterns mm/in. A Note: Land Patterns for Concave and Convex termination can be the same. B C D 8/05/02 Standard Packages & Style Codes Convex Termination Concave Termination Termination Area 741X043 2 Resistors 4 Terminations 741C083 4 Resistors 8 Terminations 742C043 2 Resistors 4 Terminations 741X083 4 Resistors 8 Terminations 742C163 8 Resistors 16 Terminations 742C083 4 Resistors 8 Terminations 50 mil pitch (1.27mm) 743C043 2 Resistors 4 Terminations Termination Area 741X163 8 Resistors 16 Terminations 742X083 4 Resistors 8 Terminations 50 mil pitch (1.27mm) Common Pad Designator 743C083 4 Resistors 8 Terminations 50 mil pitch (1.27mm) 745X101 8 Resistors 10 Terminations 744C043 2 Resistors 4 Terminations 744C083 4 Resistors 8 Terminations 745X102 8 Resistors 10 Terminations Note: The Marking Concept for Convex and Concave Series 745 is Different. 25 mil pitch (.64mm) 50 mil pitch (1.27mm) PAD 1 Mark (Dot) 745C101 8 Resistors 10 Terminations PAD 1 Mark (Triangle) 745C102 8 Resistors 10 Terminations Eight Bussed Resistors in nearly the same space as one 1206 size chip resistor! 746X101 8 Resistors 10 Terminations 8/05/02 Environmental Performance Specifications Max. Delta R Test Test Description 741 742-746 Thermal Cycle 1.0% 1.0% 5 Cycles -55°C to +125°C Short Time Overload 2.5% 1.0% 2½ X Rated Working Voltage for 5 Seconds Moisture Resistance 5.0% 2.0% 240 Hours 10% rated load, -10°C to +65°, 90% R.H. High Temperature Exposure 1.0% 1.0% 1000 Hours, no load, +125°C Load Life 5.0% 2.0% 1000 Hours @ 70°C, rated load Resistance to Solder Heat 2.0% 1.0% 10 Seconds @ 260°C solder Resistance to Solvents Isopropyl alcohol, Freon TMC Solderability RMA Flux, 230°C, 5 Seconds dip, 95% coverage Standard Resistor Values & EIA Code Ohms Ohms Code Code Ohms Ohms Code Code Ohms Ohms Code Code Ohms Ohms Code Code Ohms Ohms Code Code Ohms Ohms Code Code 0 000 68 680 470 471 3.9K 392 33K 333 270K 274 10 100 75 750 510 511 4.7K 472 39K 393 330K 334 12 120 82 820 560 561 5.1K 512 47K 473 390K 394 15 150 100 101 680 681 5.6K 562 51K 513 470K 474 18 180 110 111 820 821 6.8K 682 56K 563 510K 514 22 220 120 121 1K 102 8.2K 822 68K 683 560K 564 27 270 150 151 1.2K 122 10K 103 82K 823 680K 684 33 330 180 181 1.5K 152 12K 123 100K 104 820K 824 39 390 220 221 1.8K 182 15K 153 120K 124 1M 105 47 470 270 271 2.2K 222 18K 183 150K 154 51 510 330 331 2.7K 272 22K 223 180K 184 56 560 390 391 3.3K 332 27K 273 220K 224 Note: 0 Ohm Jumper Resistance<.05 Ohms Part Code Tolerance = X Part Part Marking is “0" Number Code For Ordering 742X083101J Style Code Resistor Code 3 digit EIA Shown Above See Standard Package Styles 741X043 741C083 741X083 742C043 741X163 Parts/Reel 10,000 Pitch 2mm Tolerance J = ±5% (Standard) G=±2% F=±1% X for zero ohm jumper Notes: No dashes or spaces in the part number. (Example) 742X083101J Marking on the Part Includes Resistor Code Only (741C,742, 743, 744, 745, 746). No Marking on the Part for 741X Series. Tape & Reel Information Style Series 745 33 to 470KOhm Series 746 33 to 100KOhm 742C083 742X083 742C163 743C043 743C083 744C043 744C083 745C101 745C102 745X101 745X102 746X101 5000 5000 4000 4000 4000 4000 2000 4mm 4mm 4mm 4mm 4mm 4mm 8mm 4000 4000 5000 4mm 4mm 4mm Carrier Width 8mm 8mm 8mm 12mm 8mm 12mm 8mm 12mm 12mm 12mm 8mm Material paper paper paper plastic plastic plastic plastic plastic plastic plastic paper Order From: Your local CTS REPRESENTATIVE or CTS Corporation, Resistor/Electrocomponents 406 Parr Road, Berne, Indiana 46711 Tel:(260)-589-3111 Fax:(260)-589-3243 http://www.ctscorp.com