ETC CAT6

Cat.6 4 Pair UTP Cable
Application:
•
•
•
•
•
•
•
•
•
Voice
Fast Ethernet(IEEE802.3u)
100Vg-AnyLAN(IEEE 802.12)
Token Ring(IEEE 802.5)
TP-PMD(ANSI X3T9.5)
100Base-T Ethernet(IEEE 802.5)
155/622 Mbps 1.2/ 2.4 Gbps ATM
1000Base-T Ethernet
550 MHz Broadband Vedio
Industry Standard:
•
•
•
•
UL, C(UL), ETL Verified
TIA/EIA 568B
ISO/IEC 11801
EN 50173
Cable Data:
•
•
•
•
•
•
•
No. of Pairs:4
Jacket Color:Gray
Insulation Thickness: 0.33mm
Nom.O.D.:6.5mm
Flame Rating:CM
Package: Reel, 305m(1,000ft)/ box
Transmission quality verified up to 250MHz
Frequency
(MHz)
Product Electrical Characteristics:
•
•
•
•
Attenuation Max.
dB/100M
Impedance:100 ± 15 ohms
Mutual Capacitance, max. nf/ 100m: 5.6
DC Resistance, max. Ohms/ 100m: 9.38
Capacitance Unbalance(Pair to Ground):
330pf/ 100m max.
NEXT
dB/100m
Power Sum
Minimum dB/100m
EFLEXT
(dB/ 100m)
1
2.0
74.3
72.3
67.0
4
3.8
65.3
63.3
55.0
10
6.0
59.3
57.3
46.8
16
7.6
56.2
54.2
42.7
20
8.5
54.8
52.8
40.8
31.25
10.7
51.9
49.9
36.9
62.5
15.5
47.4
45.4
30.9
100
19.9
44.3
42.3
26.8
200
29.2
39.8
37.8
20.8
250
33.0
38.3
36.3
18.8
P/N
1101-04001
Description
•
•
•
•
Conductor:24AWG Bare Solid Copper
Insulation:HDPE, FRPE, 100%FEP
Ripcord:Under jacket (For Bare Solid Copper)
Jacket:FRPVC
L
A
N
3
Cat.6 UTP Patch Cord
Application:
•
•
•
•
•
•
•
•
•
Voice
Fast Ethernet(IEEE802.3u)
100Vg-AnyLAN(IEEE 802.12)
Token Ring(IEEE 802.5)
TP-PMD(ANSI X3T9.5)
100Base-T Ethernet(IEEE 802.5)
155/622 Mbps 1.2/ 2.4 Gbps ATM
1000Base-T Ethernet
550 MHz Broadband Vedio
Industry Standard:
•
•
•
•
UL, C(UL), ETL Verified
TIA/EIA 568B
ISO/IEC 11801
EN 50173
1201-04002
Product Description:
•
•
•
•
•
•
Molded boots prevent pin from bending and cables from kink
Fully tested to meet EIA/ TIA-568B Category 6 requirements
Category 6 stranded 24AWG wires provides maximum flexibility
ETL verified to EIA/ TIA-568B specifications
UL, C(UL) listed
Wiring: T568B
P/N
•
4
Description
1201-04002
Cat.6 4 Pair UTP Patch Cord, 2 meter (Gray color)
1201-04003
Cat.6 4 Pair UTP Patch Cord, 3 meter (Gray color)
1201-04004
Cat.6 4 Pair UTP Patch Cord, 5 meter (Gray color)
For special requirements please contact with us
L
A
N
Cat.6 Keystone Jack
NEW
Industry Standard:
•
•
•
•
•
Compliant Press fit IDC
connector terminal for
high frequency
application
UL, C(UL) listed
Meets FCC parts 68
ANSI/TIA/ EIA-568B
ISO/IEC 11801
ETL verified EIA/TIA T568B:Cat.6 channel link
transmission performance
Physicals:
•
•
•
•
IDC connector accept 22-26 AWG solid
wire
Jack wiring:50 u” gold plated over 100 u”
nickel
Housing:High impact flame retardant
plastic UL94V-0 rated
IDC connector suitable for 110 punch
down and Krone tool
1305-04003
Mechanical:
•
•
IDC connector with large
spacer of each pair to
improve crosstalk
Plug insertion life:750 cycle min.
Plug retention force:30 lbs min.
Electrical:
•
•
•
•
•
Current rating:1.5 Amps
Insulation resistance:500Mega-ohms min.
Contact resistance:20 Milli-ohms max.
DC resistance:0.1 ohms max.
Data transmission rates up to 250Mbps
1305-04002
P/N
•
Description
1305-04002
Cat.6 110/ Krone right-angle (90º) Keystone Jack, T568A/ B
1305-04003
Cat.6 110/ Krone vertical (180º) Keystone Jack, T568A/ B
Package: 100 pcs/ box
L
A
N
5
Cat.6 Unshielded Patch Panel
NEW
110 Enhanced Cat.6 Patch Panel:
•
•
•
•
•
•
High performance, exceed EIA/ TIA 568B Category 6 channel link requirements
110 and Krone dual type IDC termination
19” 24 port patch panel, 1U size & 48 port panel, 2U size
Accepts 22-26 AWG, stranded or solid wire
Wiring:T568A/ B
Optional rear cable management
1499-00001
1402-04001
High-low contact design to
improve transmission
performance
P/N
6
L
IDC connector with large
spacer of each pair to
improve crosstalk
Compliant Press fit IDC
connector terminal for high
frequency application
Description
1402-04001
Cat.6 19” 110/ krone dual type Patch Panel 24 ports, 1U size
1402-04003
Cat.6 19” 110/ krone dual type Patch Panel 48 ports, 2U size
1499-00001
19” Rear cable management
A
N
Cat.6 110 Cross-Connect Block & Panel
w/Mounting legs
50 pair: 1801-01003
100 pair: 1801-02004
w/o Mounting legs
50 pair: 1802-01005
100 pair: 1802-02002
1803-02003
•
•
•
•
•
Labels are placed on top of label holders.
Exceeds TIA/EIA 568 Category 6 performance specifications
Terminates 22 AWG through 26 AWG solid or stranded wire
Wiring blocks and connecting blocks sold separately
19” Cross-Connect Panel make terminatins from the front
Connecting blocks
4 pair: 1804-03002
5 pair: 1804-04001
Cat.6 110 to RJ-45(110) Patch Cord
•
•
•
•
•
Make quick, simple 110-bolck connections
Category 6 stranded cable, colored pvc jacket
110 to RJ-45 type to convert one channel on a 110
block to a modular jack
110 to 110 type to link two 110 blocks
Wiring: T568B(110 to RJ-45 type), straight-through
(110 to 110 type)
110 to RJ-45 type
1202-04001
P/N
110 to 110 type
1203-04001
Description
1801-01003
Wiring blocks w/Mounting legs, w/ label holder, w/ o connecting blocks, 50pair
1801-02004
Wiring blocks w/Mounting legs, w/ label holder, w/ o connecting blocks,100pair
1802-01005
Wiring blocks w/o mounting legs, w/ label holder, w/ o connecting blocks,50pair
1802-02002
Wiring blocks w/o mounting legs, w/ label holder, w/ o connecting blocks,100pair
1804-03002
Cat.6 Connecting blocks, 4pair (100 pcs/ bag)
1804-04001
Cat.6 Connecting blocks, 5pair (100 pcs/ bag)
1803-02003
Cat.6 19” cross-connect panel, 100pair
1202-04001
Cat.6 Patch cord T568B(110 to RJ-45 type), 3meter
1203-04001
Cat.6 Patch cord T568B(110 to 110 type), 3 meter
L
A
N
7
110 Cross-Connect Block Installation Step
8
L
A
N
Step 1:
Mount the wiring base and legs onto a
suitable mounting surface with the
necessary screws and hardware. Then
lace the cables through the appropriate
openings in the wiring base.
Step 2:
Strip off the cable jacket with the jacket
stripped tool.
Step 3:
Seating the wire in accordance with the
wiring schemes (see page No.57 to page
No.58) onto the wiring base.
Step 4:
Seating the conductors and trim off the
excess wire with the cutting edge of the
impact tool.
Step 5:
Insert an 4 pair or 5 pair of 110
connecting block into the head of the
impact tool.
Step 6:
seating the 110 connecting block with the
impact tool onto the wiring base.