Continental Device India Limited An ISO/TS16949 and ISO 9001 Certified Company PNP SILICON PLANAR EPITAXIAL TRANSISTOR MPS4356 TO-92 Plastic Package E BC General Purpose Amplifier ABSOLUTE MAXIMUM RATINGS DESCRIPTION Collector Base Voltage SYMBOL VCBO VALUE 80 UNITS V Collector Emitter Voltage VCEO 80 V Emitter Base Voltage VEBO 5.0 V IC 800 mA PD 625 5.0 mW mW/ºC Tj, Tstg - 55 to +150 ºC THERMAL CHARACTERISTICS Junction to Case Rth (j-c) 83.3 ºC/W Junction to Ambient in free air Rth (j-a) 200 ºC/W Collector Current Power Dissipation @ Ta=25ºC Derate Above 25ºC Operating And Storage Junction Temperature Range ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION *VCEO IC=10mA, IB=0 Collector Emitter Voltage VCBO IC=10µA, IE=0 Collector Base Voltage Emitter Base Voltage Collector Cut Off Current VEBO ICBO IE=10µA, IC=0 VCB=50V, IE = 0 MIN 80 IEBO DC Current Gain *hFE Collector Emitter Saturation Voltage Base Emitter Saturation Voltage *VCE (sat) *VBE (sat) MAX UNITS V 80 V 5 V VCB=50V, IE=0, Ta=75ºC Emitter Cut Off Current TYP VEB=4V, IC = 0 VCE=10V, IC=100µA VCE=10V, IC=1mA 25 VCE=10V, IC=10mA 50 VCE=10V, IC=100mA 40 VCE=10V, IC=500mA 30 50 nA 5.0 µA 100 nA 40 250 IC=150mA, IB=15mA 0.15 V IC=500mA, IB=50mA 0.50 V IC=150mA, IB=15mA 0.90 V IC=500mA, IB=50mA 1.10 V *Pulse test pulse width<300µ s, duty cycle <2% MPS4356Rev180303E Continental Device India Limited Data Sheet Page 1 of 5 PNP SILICON PLANAR EPITAXIAL TRANSISTOR MPS4356 TO-92 Plastic Package E BC ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DYNAMIC CHARACTERISTICS DESCRIPTION Output Capacitance Input Capacitance SYMBOL Cob Cib Small Signal Current Gain hfe Noise Figure NF SWITCHING CHARACTERISTICS DESCRIPTION Turn On Time Turn Off Time SYMBOL ton t off TEST CONDITION VCB=20V, IE=0,f=1MHz VBE=0.5V, f=1MHz IC=0.5V, VCE=10V, f=100MHz VCE=10V, IC=100mA, RS=1KΩ, f=1KHz, BW=1Hz TEST CONDITION VCC=30V, IC=500mA, IB1=IB2=50mA MIN TYP MAX 30 110 1.0 MIN UNITS pF pF 5.0 TYP 3.0 dB MAX 100 400 UNITS ns ns MPS4356Rev180303E Continental Device India Limited Data Sheet Page 2 of 5 MPS4356 TO-92 Plastic Package TO-92 Plastic Package A Uncontrolled DIM MIN. MAX. 5.33 4.32 A B 5.20 4.45 4.19 3.18 C D 0.55 0.41 0.50 0.35 E F 5 DEG 1.40 G 1.14 H 1.40 1.20 12.70 K — L 1.982 2.082 1.20 1.03 M All dimensions are in mm 1 K 2 D 3 E Beyond 'L' Solderability Ensured L Dimension With 'L' B D SEC AA A A G F C 3 2 1 H M F Mold Parting Line PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER 3 2 1 The TO-92 Package, Tape and Ammo Pack Drawings are correct as on the date of issue/revision of this Data Sheet. The currently valid dimensions and information, may please be confirmed from the TO-92 Drawing in the Packages and Packing Section of the Product Catalogue. Packing Details PACKAGE STANDARD PACK INNER CARTON BOX OUTER CARTON BOX Details Net Weight/Qty Size Qty Size Qty Gr Wt TO-92 Bulk 1K/polybag 200 gm/1K pcs 3" x 7.5" x 7.5" 5K 17" x 15" x 13.5" 80K 23 kgs TO-92 T&A 2K/ammo box 645 gm/2K pcs 12.5" x 8" x 1.8" 2K 17" x 15" x 13.5" 32K 12.5 kgs MPS4356Rev180303E Continental Device India Limited Data Sheet Page 3 of 5 MPS4356 TO-92 Plastic Package TO-92 Tape and Ammo Pack Tape Mechanical Data h (p) P T h h1 Ammo Pack Style Adhesive Tape on Top Side h1 A1 Flat side A H3 H2 Label C1 H1 Ho Wo L Carrier Strip 186 (7.3") W2 C2 D FEE W1 W F1 F2 Do 332 F t1 (1. 43 7") P2 t Po ") (1 3 Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions are in mm ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT * 1 FEED HOLE PITCH * 2 FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS * 3 COMPONENT ALIGNMENT SIDE VIEW * 4 COMPONENT ALIGNMENT FRONT VIEW TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER * 5 TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCE STAND OFF CLINCH HEIGHT LEAD PARALLELISM PULL - OUT FORCE SPECIFICATION SYMBOL A1 A T P Po MIN. NOM. MAX. 4.0 4.8 3.9 TOL . NOTES 4.8 5.2 4.2 1. Maximum alignment deviation between leads will not to be greater than 0.2mm. 12.7 12.7 ± 1.0 ± 0.3 2. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. P2 6.35 ± 0.4 F 5.08 + 0.6 - 0.2 3. Holddown tape will not exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. h h1 W Wo W1 0 0 18 6 9 W2 Ho H1 L Do t F1, F2 0.5 16 H2 H3 | C1 - C2 | (p) 1.0 1.3 ± 0.5 ± 0.2 + 0.7 - 0.5 4. There will be no more than three (3) consecutive missing components in a tape. 5. A tape trailer, having at least three feed holes are provided after the last component in a tape. ± 0.2 ± 0.5 6. Splices should not interfere with the sprocket feed holes. ± 0.2 REMARKS 23.25 11.0 4 1.2 2.54 0.45 6N 1.45 3.0 0.22 + 0.4 - 0.1 * 1 Cumulative pitch error 1.0 mm/20 pitch * 2 To be measured at bottom of clinch * 3 At top of body * 4 At top of body * 5 t1 0.3 – 0.6 mm MPS4356Rev180303E Continental Device India Limited Data Sheet Page 4 of 5 Notes MPS4356 TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the CDIL Web Site/CD are believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119 [email protected] www.cdilsemi.com MPS4356Rev180303E Continental Device India Limited Data Sheet Page 5 of 5