TECHNICAL DATA 5-V/100MA LOW POWER LOW-DROP FIXED-VOLTAGE REGULATOR WITH LOW CURRENT CONSUMPTION The ILE 4264-2 is a monolithic integrated Low power low-drop fixed voltage regulator 5-V/100mA with low current consumption. The ILE 4264-2 is specially designed to create power source with 5V output voltage, loads up to 100 mA and drop voltage less than 0,5V. The regulator is designed to supply electronic device in automotive applications and some another applications. The ILE 4264-2 is equipped with additional protection against overvoltage of both polarities, load current limitation, short-circuit and over temperature shutdown of output voltage. The IC is supplied in chip (unpackaged) form. ILE 4264-2 ILE4264-2 P-SOT223-4-1 Features • Output voltage tolerance 5±3% (±2% up to 50 mA) • Low-drop voltage • Current capability up to150 mA • Very low current consumption • Over temperature protection • Reverse polarity proof Short-circuit proof • Junction temperature -40 tо +150°С • Suitable for use in automotive electronics • Short-circuit proof Block Diagram Rev. 00 ILE4264-2 Pin description (for P-SOT223-4 package) Pin 01 03 02, 04 Symbol I Q GND Function Input voltage; block to ground directly with a ceramic capacitor 5-V output voltage; block to ground with a capacitor Ground Typical electric parameters (UI=13,5 V, -40 oC ≤ TJ ≤ 125 oC, unless specified otherwise) Parameter, unit of measurement Symbol Mode of measurement Typical value Power Supply Ripple Rejection, dB PSRR fr = 100 Hz, Ur = 3 V (peek-to-peek) 68 Absolute Maximum Ratings Maximum Ratings Parameter, symbol Unit Junction temperature, ТJ Storage temperature, Тstg Input voltage, UI Input current, II C o C V mA Min -40* 6 - Ground pin current, IGND Output voltage, UQ Output current (pin 3), IQ mA V mA 4,9 - C/W - Max 125 28 Internally limited 5,1 Internally limited 25** - 220** Thermal Resistances Junction-case , Rth jc, for conventional case P-SOT223-4-1 Thermal Resistances Junction-ambient, Rth ja, for conventional case P-SOT223-4-1, - without heat sink o o Absolute Maximum Ratings Min Max -40* 150 -50 150 -42 45 Internally limited 50*** -0,3*** 32*** Internally limited 25** o C/W - * Ambient temperature ** Rth ja - Thermal Resistances Junction-ambient *** - Voltage is not applied to pin I Thermal resistance junction ambient for IC with heat dissipater is calculated by formula: Rth ja = Rth jc + Rth ca, Rth jc - thermal resistance junction case, oC /W. Application circuit and heat dissipater have to provide TJ ≤ 125 oС. Maximum power Ptot,Вт, dissipated by IC for TA , is calculated by formula: Ptot = (125 - TA) / Rth ja , 125 – maximum permitable operating junction temperature, ОС 220** (1) (2) Rev. 00 ILE4264-2 Electric parameters (UI=13,5 V, -40 oC ≤ TJ ≤ 125 oC, unless specified otherwise) Parameter, unit of measurement Output voltage, V Symbol Mode of measurement UQ 9 V ≤ UI ≤ 16 V 5 mA ≤ IQ ≤ 50 mA 6 V ≤ UI ≤ 21 V 5 mA ≤ IQ ≤ 100 mA 4,8 V ≤ UQ ≤ 5,2 V IQ=0,1 mA, (TJ ≤ 85oC) IQ = 0,1 mA IQ = 50 mA IQ = 100 mA 1 mA ≤ IQ ≤ 100 mA UI = 13,5 V 6 V ≤ UI ≤ 28V IQ = 1 mA Maximum output current, mA Consumption current, mA, Iq = II - IQ IQmax Iq Drop-out voltage, V Load regulation, mV UDr ΔUQ(I) Line regulation, mV ΔUQ(U) Typical value Min Max 4,9 5,1 4,85 5,15 150 - 500 0,06 0,07 4 0,5 90 - 30 Note 1 Notes 1 Drop voltage UDr = UI - UQ (measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V). ILE4264-2 Application Circuit Input 09, 07 C1I 470 uF I Q C2I 100 nF 01, 02 Output CQ 10 uF IL INH GND 08 Rev. 00 ILE4264-2 Typical Performance Characteristics Rev. 00 ILE4264-2 Rev. 00 ILE4264-2 Package Dimensions P-SOT 223-4-1 Rev. 00