TECHNICAL DATA ILE4264-2 5-V/100mA Low Power Low-Drop Fixed-Voltage Regulator with low current consumption The ILE 4264-2 is a Monolithic Integrated Low Power Low-Drop Fixed Voltage Regulator 5-V/100mA with low current consumption. The ILE 4264-2 is specially designed to create power source with 5V output voltage, loads up to 100 mA and drop voltage less than 0.5V. The regulator is designed to supply electronic device in automotive applications and some another applications. The ILE 42642 is equipped with additional protection against overvoltage of both polarities, load current limitation, short-circuit and over temperature shutdown of output voltage. P-SOT223-4-1 Ordering Information ILE4264-2G ORDERING INFORMATION Device ILE4264-2GET Operating Temperature Range TJ= -40 to 125 C Package Packing P-SOT223-4-1 T&R Features Output voltage tolerance 5V 3% (2% up to 50 mA) Low-drop voltage Current capability up to150 mA Very low current consumption Over temperature protection Reverse polarity proof Junction temperature -40 tо +150С Suitable for use in automotive electronics Short-circuit proof AEC-Q100 Qualified ESD Protection : HBM ±8.000V / MM ±400V / CDM ±2.000V Block Diagram 2012, November, Rev. 04 ILE4264-2 Pin Description (for P-SOT223-4 package) Pin 01 03 02, 04 Symbol I Q GND Function Input voltage; block to ground directly with a ceramic capacitor 5-V output voltage; block to ground with a capacitor (CQ ≥10 ㎌, ESR≤4Ω) Ground Absolute Maximum Ratings Parameter Symbol Min Max Unit Input voltage VI -42 45 V Input current II Ground pin current Output voltage IGND VQ Output current limited internally 50 -0.3 32 mA V limited internally IQ Junction temperature Storage temperature TJ Tstg Note -40 -50 150 150 o C C o * Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Operating Range Parameter Symbol Min Max VI ТJ 6 -40 28 125 Symbol Min Max Thermal Resistances Junction-case , for conventional case P-SOT223-4-1 Rth jc - 25* o Thermal Resistances Junction-ambient, for conventional case P-SOT223-4-1, - without heat sink Rth ja - 220* o Input voltage Junction temperature Unit V C o Thermal Resistances Parameter Unit C/W C/W * Rth ja - Thermal Resistances Junction-ambient Thermal resistance junction ambient for IC with heat dissipater is calculated by formula: Rth ja = Rth jc + Rth ca o Rth jc - thermal resistance junction case, C /W. o Application circuit and heat dissipater have to provide T J 125 С. Maximum power Ptot, Вт, dissipated by IC for TA, is calculated by formula: Ptot = (125 - TA) / Rth ja О 125 – maximum permitable operating junction temperature, С (1) (2) 2012, November, Rev. 04 ILE4264-2 Electrical Characteristics (VI=13.5 V, -40 C TJ 125 C, unless specified otherwise) o o Limit Value Parameter Output voltage Maximum output current Symbol VQ IQmax Test Conditions 9 V VI 16 V 5 mA IQ 50 mA 6 V VI 21 V 5 mA IQ 100 mA 4.8 V VQ 5.2 V Min Typ Max 4.9 5.0 5.1 4.85 5.0 5.15 Iq Drop-out voltage VDr 500 mA IQ=0.1 mA, (TJ 85 C) IQ = 0.1 mA IQ = 50 mA - 0.06 0.07 4 mA IQ = 100 mA - 0.5 V Load regulation VQ(I) - 90 mV Line regulation VQ(V) - 30 mV 1 mA IQ 100 mA VI = 13.5 V 6 V VI 28V IQ = 1 mA 0.25 Note V 150 o Consumption current Iq = II - IQ Unit 1 Note: 1 Drop voltage VDr = VI - VQ (measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V). Typical Performance Parameters (VI=13.5 V, -40 oC TJ 125 oC, unless specified otherwise) Parameter Power Supply Ripple Rejection Symbol Test Condition Typical Value Unit PSRR fr = 100 Hz, Vr = 3 V (peek-to-peek) 68 dB 2012, November, Rev. 04 ILE4264-2 Application Circuit Input Output 09, 07 C1I 470 uF I Q C2I 100 nF 01, 02 CQ 10 uF I L E GND 4 08 2 6 4 In the ILE4264-2 the output voltage is divided and compared2 to an internal reference of 2.5 V typical. The regulation loop controls the output to achieve an output G voltage of 5V with an accuracy INH of ±3% at an input voltage range of 5.5 V < VI < 45 V. Figure shows a typical application circuit. For stability of the control loop the ILE4264-2 output requires an output capacitor CQ of at least 10 μF with a maximum permissible ESR of 4Ω. Tantalum as well as multi layer ceramic capacitors are suitable. At the input of the regulator an input capacitor is necessary for compensating line influences (100nF ceramic capacitor recommended). A resistor of approx. 1Ω in series with CI, can damp any oscillation occurring due the input inductivity and the input capacitor. In the application circuit shown in Figure an additional electrolytic input capacitor of 470 μF is added in order to buffer supply line influences. This capacitor is recommended, if the device is sourced via long supply lines of several meters. The ILE4264-2 can supply up to 150 mA. However for protection for high input voltage above 25 V, the output current is reduced (SOA protection). 2012, November, Rev. 04 ILE4264-2 Typical Performance Characteristics 2012, November, Rev. 04 ILE4264-2 Typical Performance Characteristics (continue) 2012, November, Rev. 04 ILE4264-2 Package Dimensions P-SOT 223-4-1 2012, November, Rev. 04