IKSEMICON ILN2003AN

TECHNICAL DATA
HIGH-VOLTAGE HIGH-CURRENT
DARLINGTON TRANSISTOR ARRAYS
The ILN2003A are monolithic high-voltage, high-current
Darlington transistor arrays. Each consists of seven n-p-n
Darlington pairs that feature high-voltage outputs with commoncathode clamp diodes for switching inductive loads. The collectorcurrent rating of a single Darlington pair is 500 mA. The
Darlington pairs may be paralleled for higher current capability.
Applications include relay drivers, hammer drivers, lamp drivers,
display drivers (LED and gas discharge), line drivers, and logic
buffers.
The ILN2003A has a 2.7-k series base resistor for each
Darlington pair for operation directly with TTL or 5-V CMOS
devices.
•
•
•
•
•
500-mA Rated Collector Current (Single Output)
High-Voltage Outputs . . . 50 V
Output Clamp Diodes
Inputs Compatible With Various Types of Logic
Relay Driver Applications
LOGIC SYSBOL
ILN2003A
ORDERING INFORMATION
ILN2003AN Plastic
ILN2003AD SOIC
TA = -20°C to 85° C for all
packages
LOGIC DIAGRAM
SCHEMATICS (each Darlington Pair)
All resistor values shown are nominal.
ILN2003A: RB = 2.7 kW
1
ILN2003A
Absolute maximum ratings at 25°C free-air temperature (unless otherwise noted)
Collector-emitter voltage
Input voltage, VI (see Note 1)
collector current (see Figures 14 and 15)
Output clamp current, IOK
Total emitter-terminal current
Continuous total power dissipation
Operating free-air temperature range, TA
Storage temperature range, Tstg
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
50 V
30 V Peak
500 mA
500 mA
–2.5 A
See Dissipation Rating Table
–20°C to 85°C
–65°C to 150°C
260°C
NOTE 1: All voltage values are with respect to the emitter/substrate terminal E, unless otherwise noted.
Electrical characteristics, TA = 25°C (unless otherwise noted)
2
ILN2003A
PARAMETER MEASUREMENT INFORMATION
3
ILN2003A
Figure 9. Propagation Delay-Time Waveforms
NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 .
B. CL includes probe and jig capacitance.
C. VIH = 3 V;
Figure 10. Latch-Up Test Circuit and Voltage Waveforms
4
ILN2003A
TYPICAL CHARACTERISTICS
COLLECTOR-EMITTER
SATURATION VOLTAGE
vs
COLLECTOR CURRENT
(ONE DARLINGTON)
COLLECTOREMITTER
SATURATION VOLTAGE
vs
TOTAL COLLECTOR CURRENT
COLLECTOR CURRENT
vs
INPUT CURRENT
5
ILN2003A
THERMAL INFORMATION
D PACKAGE
MAXIMUM COLLECTOR CURRENT
Vs
DUTY CYCLE
N PACKAGE
MAXIMUM COLLECTOR CURRENT
vs
DUTY CYCLE
Figure 14
Figure 15
APPLICATION INFORMATION
6
ILN2003A
7
ILN2003A
N SUFFIX PLASTIC DIP
(MS - 001BB)
A
Dimension, mm
9
16
B
1
8
Symbol
MIN
MAX
A
18.67
19.69
B
6.10
7.11
5.33
C
F
L
C
-T- SEATING
PLANE
N
G
K
D
M
H
J
0.25 (0.010) M T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.20
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AC)
Dimension, mm
A
16
9
H
B
1
G
P
8
R x 45
C
-TK
D
SEATING
PLANE
J
0.25 (0.010) M T C M
F
M
Symbol
MIN
MAX
A
9.80
10.00
B
3.80
4.00
C
1.35
1.75
D
0.33
0.51
F
0.40
1.27
G
1.27
H
5.72
J
0°
8°
K
0.10
0.25
1. Dimensions A and B do not include mold flash or protrusion.
M
0.19
0.25
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
P
5.80
6.20
R
0.25
0.50
NOTES:
8