TECHNI CAL DATA HIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS ILN2004 The ILN2004 are monolithic high-voltage, high-current Darlington transistor arrays. Each consists of seven n-p-n Darlington pairs that feature high-voltage outputs with commoncathode clamp diodes for switching inductive loads. The collectorcurrent rating of a single Darlington pair is 500 mA. The Darlington pairs may be paralleled for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers. The ILN2004 has a 10.5kΩ series base resistor for each Darlington pair for operation directly with 6-15V CMOS devices. • • • • • 500-mA Rated Collector Current (Single Output) High-Voltage Outputs . . . 50 V Output Clamp Diodes Inputs Compatible With Various Types of Logic Relay Driver Applications LOGIC SYMBOL ORDERING INFORMATION ILN2004N Plastic ILN2004D SOIC TA = -20°C to 85° C for all packages LOGIC DIAGRAM SCHEMATICS (each Darlington Pair) ILN2004: RB = 10.5 kΩ All resistor values shown are nominal. 2011, January, Rev. 00 I L N2004 Absolute maximum ratings at 25°C free-air temperature (unless otherwise noted) Symbol Parameter Collector-emitter voltage Input voltage(see Note 1) Peak collector current (see Figures 14 and 15) Output clamp current Total emitter-terminal current Continuous total power dissipation Operating free-air temperature range Storage temperature range Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds VI IOK TA Tstg Value Unit 50 30 500 500 –2.5 V V mA mA A See Dissipation Rating Table °C °C °C –20 to 85 –65 to 150 260 NOTE 1: All voltage values are with respect to the emitter/substrate terminal E, unless otherwise noted. Dissipation Rating Table PACKAGE D N TA=25°C POWER RATING 950mW 1150mW TA=85°C POWER RATING 494mW 598 mW DERATING FACTOR above TA=25°C 7.6mW/°C 9.2mW/°C Electr ical Char acter istics, TA = 25°C (unless otherwise noted) Symbol Par ameter Vi(on) Input Voltage V CE(sat) Test Figur e 6 Ii(off) Collector-emitter Saturation Voltage Output Leakage Current Clamp Diode Forward Voltage Off-state Input Current Ii Input Current 4 IR Clamp Reverse Current 7 I CEX VF 5 2 8 3 Test Conditions M in. V CE= 2V I C = 125mA I C = 200mA I C = 275mA I C = 350mA I C = 100mA, I B = 250mA I C = 200 mA, I B = 350mA I C = 350mA, I B = 500mA V CE = 50V, Vi = 1V I F = 350mA V CE= 50V, Tamb = 70°C, I C = 500mA Vi = 5V Vi = 12V V R = 50V Tamb = 70°C, V R = 50V Turn-on Delay Time Turn-off Delay Time V OH High level output voltage after switching See Fig.9 See Fig.9 V S= 50V, I O= 300mA See Fig.10 M ax. Unit V 0.9 1.1 1.3 1.7 50 5 6 7 8 1.1 1.3 1.6 500 2 65 0.35 1 Ci Input Capacitance Switching Characteristics, TA = 25º C tPLH tPHL Typ. V S-20 V uA V uA 15 0.5 1.45 50 100 25 0.25 0.25 1 1 mA uA pF us us mV 2011, January, Rev. 00 I L N2004 PARAMETER MEASUREMENT INFORMATION 2011, January, Rev. 00 I L N2004 Figure 9. Propagation Delay-Time Waveforms NOTES: A. The pulse generator has the following characteristics: PRR = 12.5 kHz, ZO = 50 . B. CL includes probe and jig capacitance. C. VIH = 12 V; Figure 10. Latch-Up Test Circuit and Voltage Waveforms 2011, January, Rev. 00 I L N2004 TYPICAL CHARACTERISTICS COLLECTOR-EMITTER SATURATION VOLTAGE vs COLLECTOR CURRENT (ONE DARLINGTON) COLLECTOR-EMITTER SATURATION VOLTAGE vs TOTAL COLLECTOR CURRENT TWO DARLINGTONS PARALLELED) COLLECTOR CURRENT vs INPUT CURRENT 2011, January, Rev. 00 I L N2004 THERMAL INFORMATION D PACKAGE MAXIMUM COLLECTOR CURRENT vs DUTY CYCLE N PACKAGE MAXIMUM COLLECTOR CURRENT vs DUTY CYCLE Figure 14 Figure 15 APPLICATION INFORMATION 2011, January, Rev. 00 I L N2004 2011, January, Rev. 00 I L N2004 N SUFFIX PLASTIC DIP (MS - 001BB) A Dimension, mm 9 16 Symbol MIN MAX A 18.67 19.69 B 6.10 7.11 B 1 8 C F L C 5.33 D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 -T- SEATING PLANE N G K M H D J 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.20 0.36 N 0.38 D SUFFIX SOIC (MS - 012AC) Dimension, mm A 16 9 H B 1 G P 8 R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. F M Symbol MIN MAX A 9.80 10.00 B 3.80 4.00 C 1.35 1.75 D 0.33 0.51 F 0.40 1.27 G 1.27 H 5.72 J 0° 8° K 0.10 0.25 M 0.19 0.25 P 5.80 6.20 R 0.25 0.50 2011, January, Rev. 00