8700 E. Thomas Road Scottsdale, AZ 85252 Tel: (480) 941-6300 Fax: (480) 947-1503 USB50803 thru USB50824 TVSarray Series DESCRIPTION (500 watt) This TRANSIENT VOLTAGE SUPPRESSOR (TVS) array is packaged in an SO-8 configuration giving protection to 2 Unidirectional data or interface lines. It is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lighting. These TVS arrays have a peak power rating of 500 watts for an 8/20µsec pulse. This array is suitable for protection of sensitive circuitry consisting of TTL, CMOS DRAM’s, SRAM’s, HCMOS, HSIC microprocessors, UNIVERSAL SERIAL BUS (USB) and I/O transceivers. The USB508XX product provides board level protection from static electricity and other induced voltage surges that can damage or upset sensitive circuitry. FEATURES MECHANICAL • • • • • • • • • • Protects up to 2 unidirectional lines Surge protection Per IEC 1000-4-2, IEC 1000-4-4 Provides electrically isolated protection SO-8 Packaging ULTRA LOW CAPACITANCE 3 pF ULTRA LOW LEAKAGE Molded SO-8 Surface Mount Weight: 0.066 grams (approximate) Marking: Logo, device number, date code Pin #1 defined by DOT on top of package MAXIMUM RATINGS PACKAGING • • • • • • • Operating Temperatures: -550C to +1500C Storage Temperature: -550C to +1500C Peak Pulse Power: 500 Watts (8/20 µsec, Figure 1) Pulse Repetition Rate: <.01% Tape & Reel EIA Standard 481-1-A 13 inch reel 2,500, pieces (OPTIONAL) Carrier tubes 95 pcs per (STANDARD) ELECTRICAL CHARACTERISTICS PER LINE @ 250C Unless otherwise specified PART NUMBER DEVICE MARKING STAND OFF VOLTAGE VWM BREAKDOWN VOLTAGE VBR @1 mA CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS LEAKAGE CURRENT ID @ VWM CAPACITANCE (f=1 MHz) @0V C TEMPERATURE COEFFICIENT OF VBR áVBR VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS VOLTS µA pF mV/°C MAX MIN MAX MAX MAX TYP MAX USB50803 AF 3.3 4 8 11 200 3 -5 USB50805 AG 5.0 6.0 10.8 13 20 3 1 USB50812 AH 12.0 13.3 19 26 1 3 8 USB50815 AJ 15.0 16.7 25 32 1 3 11 USB50824 AK 24.0 26.7 44 57 1 3 28 NOTE: TVS product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. Application: The USB508XX product is designed for transient voltage suppression protection of ESD sensitive components at the board level. It is an ideal product to be used for protection of I/O Transceivers. MSC1536.PDF ISO 9001 CERTIFIED REV C 7/07/2000 USB50803 thru USB50824 WAVE FORMS 100 Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 0 0 20 10 30 I t td p t -- Time in microsec FIGURE 2 Pulse Wave Form p FIGURE 1 Peak Pulse Power Vs Pulse Time MOUNTING PAD SO-8 CIRCUIT DIAGRAM .160±.005 SIGNAL SIDE 0.245 MIN GROUND SIDE 0.045±.005 .030±.005 .050 TYP SO-8 PACKAGE INCHES MIN MAX MIN MAX A 0.188 0.197 4.77 5.00 B 0.150 0.158 3.81 4.01 C 0.053 0.069 1.35 1.75 D 0.011 0.021 0.28 0.53 F 0.016 0.050 0.41 G MSC1536.PDF MILLIMETERS DIM 0.050 BSC 1.27 1.27 BSC J 0.006 0.010 0.15 0.25 K 0.004 0.008 0.10 0.20 L 0.189 0.206 4.80 5.23 P 0.228 0.244 5.79 6.19 ISO 9001 CERTIFIED REV C 7/07/2000