2.0x1.25mm SMD CHIP LED LAMP Part Number: APTK2012SURC Features Description z2.0mmx1.25mm zLOW SMT LED, 0.75mm THICKNESS. zIDEAL VIEWING ANGLE. FOR BACK LIGHT AND INDICATOR. zVARIOUS COLORS AND LENS TYPES AVAILABLE. zPACKAGE : 2000PCS / REEL. zMOISTURE zRoHS The Hyper Red source color devices are made with DH InGaAlP on GaAs substrate Light Emitting Diode. POWER CONSUMPTION. zWIDE HYPER RED SENSITIVITY LEVEL : LEVEL 4. COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAC0233 REV NO: V.2 DATE: AUG/18/2006 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: W.J.ZHU ERP:1204000413 Selection Guide Dice Part No. APTK2012SURC Iv (mcd) [2] @ 20mA Lens Type WATER CLEAR HYPER RED (InGaAlP) Viewing Angle [1] Min. Typ. 2θ1/2 110 250 100° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2.Luminous Intensity / Luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Typ. Max. Units Test Conditions 640 nm IF=20mA Hyper Red 628 nm IF=20mA Spectral Line Half-width Hyper Red 27 nm IF=20mA C Capacitance Hyper Red 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.9 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 170 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAC0233 REV NO: V.2 DATE: AUG/18/2006 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: W.J.ZHU ERP:1204000413 Hyper Red APTK2012SURC SPEC NO: DSAC0233 REV NO: V.2 DATE: AUG/18/2006 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: W.J.ZHU ERP:1204000413 APTK2012SURC Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAC0233 REV NO: V.2 DATE: AUG/18/2006 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: W.J.ZHU ERP:1204000413 PACKING & LABEL SPECIFICATIONS APTK2012SURC SPEC NO: DSAC0233 REV NO: V.2 DATE: AUG/18/2006 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: W.J.ZHU ERP:1204000413