1.6x0.8mm SMD CHIP LED LAMP Part Number: APHK1608SURCK Hyper Red Features Description z1.6mmx0.8mm SMT LED, 0.7mm thickness. The Hyper Red source color devices are made with Al- zLow power consumption. GaInP on GaAs substrate Light Emitting Diode. zWide viewing angle. zIdeal for backlight and indicator. zVarious colors and lens types available. zPackage : 2000pcs / reel. zMoisture sensitivity level : level 4. zRoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.Specifications are subject to change without notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1112 REV NO: V.6 DATE: MAR/27/2009 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: X.J.Guo PAGE: 1 OF 5 ERP: 1204000405 Selection Guide Part No. Dice APHK1608SURCK Lens Type Hyper Red (AlGaInP) WATER CLEAR Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 2θ1/2 70 200 90° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 650 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1112 REV NO: V.6 DATE: MAR/27/2009 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: X.J.Guo PAGE: 2 OF 5 ERP: 1204000405 Hyper Red APHK1608SURCK SPEC NO: DSAD1112 REV NO: V.6 DATE: MAR/27/2009 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: X.J.Guo PAGE: 3 OF 5 ERP: 1204000405 APHK1608SURCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) SPEC NO: DSAD1112 REV NO: V.6 DATE: MAR/27/2009 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: X.J.Guo PAGE: 4 OF 5 ERP: 1204000405 PACKING & LABEL SPECIFICATIONS APHK1608SURCK SPEC NO: DSAD1112 REV NO: V.6 DATE: MAR/27/2009 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: X.J.Guo PAGE: 5 OF 5 ERP: 1204000405