TECHNICAL DATA QUAD 2-INPUT OR GATE KK74VHC32 is high-speed logic IC made by CMOS technology and designed for use in high-performance calculating systems with a wide supply voltage range. As for operation speed, KK74VHC32 can be compared with equivalent bipolar ICs based on Schottky TTL and two times surpasses ICs of KK74НС series. KK74VHC32 tolerates operation under conditions when voltage on input is exceeded up to 7V without affecting characteristics and IC reliability. This possibility allows to use KK74VHC32 in radio-electronic devices for interfacing with supply voltages 5V and 3V, eliminate IC failure under supply voltage source emergency outage. Use of output edge shaping block in the microcircuit allows to reduce noise amplitude of noises when switching outputs into the same state simultaneously. Input and output levels of KK74VHC32 are compatible with CMOS levels KK74VHC32 ORDERING INFORMATION KK74VHC32N Plastic KK74VHC32D SOIC TA = -40° to 85° C for all packages Features: • Supply voltage range 2.0 to 5.5 V. • Output current 8 mA. • Low consumption current: 0.2 mkA (typical value) at Та = 25 °С. • Latchup current not less than 300 mA at Та = 85 °С. • Tolerable value of static potential not less than 2000 V as per human body model (HBM) and not less than 200 V as per machine model (ММ). • Ambient operation temperature minus 40 to plus 85 °С. • Balanced signal propagation delay. • Ensures voltage exceeding mode on input • Low noise level at the simultaneous switching of outputs in the same state: VOLP = 0.8 V (max). • For pins and functions, compatible with KK74НС32. . 1 KK74VHC32 KK74VHC32 truth table Input Output A B Y= А+В L L L L H H H L H H H Note – H - high voltage level; L - low voltage level; H Pinout A1 01 14 Vcc B1 02 13 B4 Y1 03 12 A4 A2 04 11 Y4 B2 05 10 B3 Y2 06 09 A3 GND 07 08 Y3 Pins description in KK74VHC32 Pin No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 Symbol А1 В1 Y1 А2 В2 Y2 GND Y3 А3 В3 Y4 А4 В4 VCC Description Input Input Output Input Input Output Common output Output Input Input Output Input Input Supply output from voltage source 2 KK74VHC32 Absolute maximum conditions* Parameter, unit Symbol Value min -0.5 -0.5 -0.5 – – max 7.0 7.0 Vcc+0.5V -20 ± 50 Supply voltage, V VCC Input voltage, V Vin Vout Output voltage, V Input diode current, mA Iik Current of common output and supply Icc output, mA Output current, mA Iout – ± 25 Output diode current, mA Iok – ± 20 Dissipated power, mW Pd – 180 *Under absolute maximum conditions operation of microcircuit is not guaranteed. Operation is guaranteed under maximum conditions Maximum conditions Parameter, unit Supply voltage, V Input voltage,V Output voltage, V Output current, mA Input rise and fall time, ns/V at Vcc = (3.3 ± 0.3) V at Vcc = (5.0 ± 0.5) V Symbol VCC Vin Vout Iout tLH, tHL Value min 2.0 0 0 – 0 0 max 5.5 VCC VCC ± 8.0 100 20 3 KK74VHC32 DC electrical characteristics Symbo l Parameter Test conditions VIН High level input VO ≤ 0.1 V or voltage VO ≥ VCC –0.1 V VIL Low level input VO ≤ 0.1 V or voltage VO ≥ VCC –0.1 V VOH High level output VI = VIН or VIL voltage IOН = -50 uA VOL IIL VI = VIН or VIL IOН = -4 mA VI = VIН or VIL IOН = -8 mA Low level output VI = VIН or VIL voltage IOL = 50 uA VI = VIН or VIL IOL = 4 mA VI = VIН or VIL IOL = 8 mA Low level input VI = 0 В 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 3.0 Unit Value VCC, V 25 °C min 1.5 0.7 VCC 0.7 VCC 0.7 VCC - 1.92 2.92 4.42 5.42 2.58 4.5 3.94 2.0 3.0 4.5 5.5 3.0 - max - 0.5 0.3 VCC 0.3 VCC 0.3 VCC - –40 to 85 °C min max 1.5 0.7 VCC 0.7 VCC 0.7 VCC 0.5 0.3 VCC 0.3 VCC 0.3 VCC 1.9 2.9 4.4 5.4 2.48 V 3.8 0.09 0.09 0.09 0.09 0.36 - 0.1 0.1 0.1 0.1 0.44 4.5 0.36 0.44 5.5 -0.1 -1.0 5.5 0.1 1.0 0 0.1 1.0 5.5 2.0 20 uA current IIН IIН1 ICC High level input VI = VCC current High level input VI = 5.5 В current Consumption VI = 0 В или VCC current 4 KK74VHC32 AC electrical characteristics (tLH = tHL = 3.0 ns VIL = 0 V, VIН=VCC,) Symbol Parameter tPHL, tPLH Propagation delay time when switching "on", "off" CI CРD Value Test condition VCC, V s Input capacity Dynamic capacity –40 to 85 °C min max min max 7.9 9.5 11.4 13.0 5.5 6.57.5 8.5 10 28 CL, pF 25 °C 3.3 ± 0.3 15 50 5.0 ± 0.5 15 50 5.0 VI = 0 V 5.0 or VCC Unit ns pF Noise characteristics (CL = 50 pF) Parameter Symbol VOLP VOLV VIHD VILD Value VCC, V Positive noise of low output 5.0 voltage Negative noise of low output 5.0 voltage Input dynamic high voltage Input dynamic low voltage 5.0 5.0 Unit min - max 0.8 -0.8 - 3.5 - 1.5 V - Time diagram of input and output pulses t LH t HL VCC 0.9 0.9 A, B 0.5 0.1 0.5 0.1 tPLH GND tPHL 0.9 0.9 Y 0.5 0.5 0.1 t TLH t THL 0.1 5 KK74VHC32 N SUFFIX PLASTIC DIP (MS - 001AA) A Dimension, mm 8 14 B 7 1 Symbol MIN MAX A 18.67 19.69 B 6.1 7.11 5.33 C F L C -T- SEATING PLANE N G M K J H D 0.25 (0.010) M T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AB) Dimension, mm A 14 8 H B 1 G P 7 R x 45 C -TK D SEATING PLANE M Symbol MIN MAX A 8.55 8.75 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 G 1.27 H 5.27 J 0° 8° K 0.1 0.25 1. Dimensions A and B do not include mold flash or protrusion. M 0.19 0.25 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. P 5.8 6.2 R 0.25 0.5 J 0.25 (0.010) M T C M NOTES: F 6