TECHNICAL DATA Octal Buffer/Line driver, INV (3-State) KK74VHC241 is high-speed logic IC made by CMOS technology and designed for use in high-performance calculating systems with a wide supply voltage range. As for operation speed, KK74VHC241 can be compared with equivalent bipolar ICs based on Schottky TTL and two times surpasses ICs of KK74НС series. KK74VHC241 tolerates operation under conditions when voltage on input is exceeded up to 7V without affecting characteristics and IC reliability. This possibility allows to use KK74VHC241 in radio-electronic devices for interfacing with supply voltages 5V and 3V, eliminate IC failure under supply voltage source emergency outage. Use of output edge shaping block in the microcircuit allows to reduce noise amplitude of noises when switching outputs into the same state simultaneously. Input and output levels of KK74VHC241 are compatible with CMOS levels KK4VHC241 ORDERING INFORMATION KK74VHC241N Plastic KK74VHC241DW SOIC TA = -40° to 85° C for all packages Features: Supply voltage range 2.0 to 5.5 V. Output current 8 mA. Low consumption current: 0.2 mkA (typical value) at Та = 25 °С. Latchup current not less than 300 mA at Та = 85 °С. Tolerable value of static potential not less than 2000 V as per human body model (HBM) and not less than 200 V as per machine model (ММ). • Ambient operation temperature minus 40 to plus 85 °С. • Balanced signal propagation delay. • Ensures voltage exceeding mode on input • Low noise level at the simultaneous switching of outputs in the same state: VOLP = 0.8 V (max). • For pins and functions, compatible with KK74HC241. • • • • • . 1 KK74VHC241 KK74VHC241 truth table Input Output 1Y L H Z Output 2Y L H Z 1A L H X 1G L L H Input 2G H H L 2A L H X Note – H - high voltage level; L - low voltage level; X - any voltage level (low or high); Z - output in third state Pins description in KK74VHC241 Pinout Pin No. 01 Symbol 1G Description Input OUTPUT ENABLE 02 1A1 Data input 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND 2A1 1Y4 2A2 1Y3 2A3 1Y2 2A4 Data output Data input Data output Data input Data output Data input Data output Common output Data input Data output Data input Data output Data input Data output Data input 1G 01 20 VCC 1A1 02 19 2G 2Y4 03 18 1Y1 1A2 04 17 2A4 2Y3 05 16 1Y2 1A3 06 15 2A3 2Y2 07 14 1Y3 1A4 08 13 2A2 2Y1 09 12 1Y4 18 19 1Y1 2G Input OUTPUT ENABLE GND 10 2A1 20 VCC Supply output from voltage source 11 Data output 2 KK74VHC241 Absolute maximum conditions* Parameter, unit Symbol Supply voltage, V Input voltage, V Output voltage, V Input diode current, mA Current of common output and supply output, mA Output current, mA Output diode current, mA Dissipated power, mW VCC Vin Vout Iik Icc Iout Iok Pd Value min max -0.5 -0.5 -0.5 – – 7.0 7.0 Vcc+0.5V -20 ± 75 – – – ± 25 ± 20 180 *Under absolute maximum conditions operation of microcircuit is not guaranteed. Operation is guaranteed under maximum conditions Maximum conditions Parameter, unit Supply voltage, V Input voltage,V Output voltage, V Output current, mA Input rise and fall time, ns/V at Vcc = (3.3 ± 0.3) V at Vcc = (5.0 ± 0.5) V Symbol VCC Vin Vout Iout tLH, tHL Value min max 2.0 0 0 – 5.5 VCC VCC ± 8.0 0 0 100 20 3 KK74VHC241 DC electrical characteristics Value Symbo l VIH Parameter High input voltage Test conditions – 25 °C VCC, V 2.0 min 1.5 3.0-5.5 0.7Vcc VIL Low input voltage VOH High output voltage VOL IOZ II ICC Low output voltage – VI = VIH or VIL IO = -50 mkA VI = VIH or VIL; IO = -4 mA VI = VIH or VIL; IO = -8 mA VI = VIH orVIL IO = 50 mkA max – –40 to 85 °C min max 1.5 – – 0.7Vcc – 2.0 – 0.5 – 0.5 3.0-5.5 2.0 3.0 4.5 5.5 – 1.92 2.92 4.42 5.52 0.3Vcc – – – – – 1.9 2.9 4.4 5.4 0.3Vcc – – – – 3.0 2.58 – 2.48 – 4.5 3.94 – 3.80 – 2.0 3.0 4.5 5.5 – – – – 0.09 0.09 0.09 0.09 – – – – 0.1 0.1 0.1 0.1 – 0.36 – 0.44 – 0.36 – 0.44 - ±0.25 - ±2.5 - ±0.1 4.0 - ±1.0 40.0 VI = VIH or VIL 3.0 IO = 4 mA VI = VIH or VIL 4.5 IO = 8 mA Output current in VI = VIH or VIL 5.5 VO = VCC or 0V "off" state Input current VI = 5.5V or 0V 0 – 5.5 Consumption current VI =VCC or 0V 5.5 Unit V mkA 4 KK74VHC241 AC electrical characteristics (tLH = tHL = 3.0 ns) Symbol Test conditi VCC, V ons Parameter tPHL, tPLH Propagation delay time Figure 3.3 ± 0.3 when switching "on", 1 "off" 5.0 ± 0.5 tPHZ , tPLZ Propagation delay time Figure 3.3 ± 0.3 under transition from 2 high , low level into "off" 5.0 ± 0.5 state tPZH , tPZL Propagation delay time Figure under transition from 2 «off» state into high, low level tOSLH, tOSHL Propagation delays – difference between outputs 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.5 ± 0.5 Value CL, pF 15 50 15 50 50 –40 to 85 °C min max min max – 8.4 – 10.0 – 11.9 – 13.5 – 5.5 – 6.5 – 7.5 – 8.5 – 14.0 – 16.0 25 °C 50 – 9.2 – 10.5 15 50 15 50 50 50 – – – – – – 10.6 14.1 7.3 9.3 1.5 1.0 – – – – – – 12.5 16.0 8.5 10.5 1.5 1.0 Unit ns Capacitance characteristics Symbol CI CO CРD Parameter Input capacity Output capacity Dynamic capacity Test conditions VI = 0 V orVCC VCC, V 5.0 5.0 5.0 Value 25 °C min max 10 12 36 Unit pF pF pF Noise characteristics (CL = 50 pF) Parameter Symbol VOLP VOLV VIHD VILD Unit Value VCC, V Positive noise of low output voltage 5.0 Negative noise of low output 5.0 voltage min -0.9 max 0.9 - Input dynamic high voltage Input dynamic low voltage 3.5 - 1.5 5.0 5.0 V 5 KK74VHC241 - Time diagram of input and output pulses tLH tHL 0.9 A 0.5 VCC 0.9 0.5 0.1 GND 0.1 tPHL tPLH VCC 0.5 Y 0.5 0V Fig. 1 tHL tLH VCC 0.9 G 0.9 0.5 0.5 0.1 0V 0.1 VCC 0.5 G 0.5 0V tPZH Y 0.9 tPHZ 0.5 0V VCC tPLZ Y VOH 0.5 tPZL 0.1 VOL Fig.2 6 KK74VHC241 N SUFFIX PLASTIC DIP (MS - 001AD) A Dimension, mm 11 20 B 1 10 Symbol MIN MAX A 24.89 26.92 B 6.1 7.11 5.33 C F L C -T- SEATING PLANE N D 0.36 0.56 F 1.14 1.78 G 2.54 H 7.62 J 0° 10° K 2.92 3.81 0.25 (0.010) M T L 7.62 8.26 1. Dimensions “A”, “B” do not include mold flash or protrusions. M 0.2 0.36 N 0.38 G K M D NOTES: J H Maximum mold flash or protrusions 0.25 mm (0.010) per side. D SUFFIX SOIC (MS - 013AC) A 20 11 H Dimension, mm B 1 P 10 G R x 45 C -TK D SEATING PLANE J 0.25 (0.010) M T C M F M Symbol MIN MAX A 12.6 13 B 7.4 7.6 C 2.35 2.65 D 0.33 0.51 F 0.4 1.27 G 1.27 H 9.53 J 0° 8° 1. Dimensions A and B do not include mold flash or protrusion. K 0.1 0.3 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side M 0.23 0.32 P 10 10.65 R 0.25 0.75 NOTES: for A; for B ‑ 0.25 mm (0.010) per side. 7