LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only LIGHT BAR LED DISPLAY LBD711SBK-XX DATA SHEET DOC. NO : QW0905- LBD711SBK-XX REV. : A DATE : 18 - Aug. - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 1/6 PART NO. LBD711SBK-XX Package Dimensions 20.35(0.801") 19±0.25 6.3(0.248") 5.0 (0.197") LBD711SBK-XX LIGITEK 4.2±0.5 Ø 0.5 TYP 12.5(0.492") 1 + PIN NO.1 2 - Note : 1.All dimension are in millimeters and (lnch) tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 2/6 PART NO. LBD711SBK-XX Internal Circuit Diagram LBD711SBK-XX 2 1 Electrical Connection PIN NO.1 LBD711SBK-XX 1 Anode 2 Cathode LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/6 PART NO. LBD711SBK-XX Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT SBK Forward Current Per Chip IF 30 mA Peak Forward Current Per Chip (Duty 1/10,0.1ms Pulse Width) IFP 100 mA Power Dissipation Per Chip PD 120 mW Ir 50 μA ESD 500 V Reverse Current Per Any Chip Electrostatic Discharge Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -25 ~ +85 ℃ Solder Temperature 1-16 Inch Below Seating Plane For 3 Seconds At 260 ℃ Part Selection And Application Information(Ratings at 25℃) Electrical Material common λP λD △λ Vf(v) Iv(mcd) IV-M cathode (nm) (nm) (nm) Typ. Max. Min. Typ. Emitted or anode InGaN/SiC Blue CHIP PART NO LBD711SBK-XX Common Anode 468 470 26 3.5 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 4.2 10.5 18 2:1 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 4/6 PART NO. LBD711SBK-XX Test Condition For Each Parameter Symbol Unit Test Condition Forward Voltage Per Chip Vf volt If=20mA Luminous Intensity Per Chip Iv mcd If=30mA Peak Wavelength λP nm If=20mA Dominant Wavelength λD nm If=20mA △λ nm If=20mA Ir μA Vr=5V Parameter Spectral Line Half-Width Reverse Current Any Chip Luminous Intensity Matching Ratio IV-M LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 5/6 PART NO. L BD711SBK-XX Typical Electro-Optical Characteristics Curve SBK CHIP Fig.2 Relative Intensity vs. Forward Current 30 1.5 Relative Intensity Normalize @20mA Forward Current(mA) Fig.1 Forward current vs. Forward Voltage 25 20 15 10 5 0 1 2 3 4 1.25 1.0 0.75 0.5 0.25 0 5 0 5 Relative Intensity@20mA Forward Current@20mA 40 30 20 10 0 50 75 Ambient Temperature( ℃) 20 25 30 Fig.4 Relative Intensity vs. Wavelength Fig.3 Forward Current vs. Temperature 25 15 Forward Current(mA) Forward Voltage(V) 0 10 100 1.0 0.5 0 380 430 480 530 580 Wavelength (nm) 630 680 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 6/6 PART NO. LBD711SBK-XX Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=10mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resisance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under ondition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hous. 1.Ta=105 ℃±5 ℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11