LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only AXIAL SERIES LED LAMPS Pb Lead-Free Parts LG9753/S8-SH DATA SHEET DOC. NO : QW0905-LG9753/S8-SH REV : A DATE : 22 - Jun. - 2009 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG9753/S8-SH Page 1/7 Package Dimensions 14.6 1.25 1.2 3.5± 0.5 0.55 12.7 1 2 1 - 2 + Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG9753/S8-SH Page 2/7 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT G Forward Current IF 30 mA Peak Forward Current Duty 1/10@10KHz IFP 120 mA Power Dissipation PD 100 mW Reverse Current @5V Ir 10 μA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO COLOR MATERIAL Emitted LG9753/S8-SH GaP Green Peak wave length λPnm Spectral halfwidth △λnm Luminous intensity @20mA(mcd) Typ. Max. Min. Lens Water Clear Forward voltage @20mA(V) 565 30 4.0 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 5.2 20 Viewing angle 2θ 1/2 (deg) Typ. 38 60 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/7 PART NO. LG9753/S8-SH Color Code G CHIP Group Wave length(nm) at 20 mA Min. Max. g2 569.6 570.5 g3 570.6 571.5 g4 571.6 572.5 g5 572.6 573.5 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG9753/S8-SH Page 4/7 Typical Electro-Optical Characteristics Curve G CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.5 Relative Intensity Normalize @20mA Forward Current(mA) 1000 100 10 1.0 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.1 1.0 2.0 3.0 4.0 5.0 1.0 10 Fig.3 Forward Voltage vs. Temperature Fig.4 Relative Intensity vs. Temperature 1.2 3.0 Relative Intensity@20mA Normalize @25 ℃ Forward Voltage@20mA Normalize @25 ℃ 1000 Forward Current(mA) Forward Voltage(V) 1.1 1.0 0.9 0.8 -40 -20 0 20 40 60 80 100 Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0.0 500 550 600 Wavelength (nm) 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 Ambient Temperature(℃) Ambient Temperature( ℃) Relative Intensity@20mA 100 650 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG9753/S8-SH Page 5/7 Soldering Iron: Basic spec is ≦5 sec when 260 ℃. If temperature is higher, time should be shorter(+10 ℃ → -1sec). Power dissipation of iron should be smaller than 15W,and temperature should be controllable. Surface temperature of the device should be under 230 ℃. Soldering heat Soldering heat Max. 260 ℃ 245±5℃ within 5 sec 120 ~ 150℃ Preheat 120 ~ 180 sec Reflow Temp/Time Temp. (℃) 220 Rising +5 ℃/sec 150 Cooling -5℃/sec Preheat 120 60 ~ 120 sec 5sec Time LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LG9753/S8-SH Page 6/7 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH<60%, they should be treated at 60 ℃± 5 ℃fo r 15hrs. Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A Circuit model B LED LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 7/7 PART NO. LG9753/S8-SH Reliability Test: Test Item Test Condition Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) High Temperature Storage Test Description Reference Standard This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. 1.Ta=105 ℃±5 ℃&-40 ℃±5 ℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 Thermal Shock Test JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11