QP-100 100W Quad Output with PFC Function series ■ Features : $Universal AC input / Full range $Built-in active PFC function, PF>0.95 $Protections: Short circuit / Overload / Over voltage $Free air cooling convection $CH4:± Polarity is selectable $Fixed switching frequency at 100KHz $3 years warranty .. SPECIFICATION QP-100-3A MODEL OUTPUT CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V 3.3V 12V -5V 5V 3.3V 12V -12V 5V 3.3V 15V -15V RATED CURRENT 8A 8A 2.5A 0.6A 8A 8A 2.2A 0.6A 8A 8A 1.7A 0.6A CURRENT RANGE 2 ~ 10A 0 ~ 10A 0.3 ~ 3A 0 ~ 1A 2 ~ 10A 0 ~ 10A 0.3 ~ 3A 0 ~ 1A 2 ~ 10A 0 ~ 10A 0.3 ~ 2A 0 ~ 1A RATED POWER (max.) 99.4W CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V ± 3.0% ± 6.0% ± 5.0% ± 3.0% ± 3.0% ± 6.0% ± 5.0% ± 3.0% ± 3.0% +8,-6% ± 5.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% LOAD REGULATION ± 2.0% ± 2.0% ± 6.0% ± 2.0% ± 2.0% ± 2.0% ± 6.0% ± 2.0% ± 2.0% ± 2.0% ± 6.0% ± 2.0% SETUP, RISE TIME 800ms, 50ms/230VAC 24ms/230VAC Note.5 90 ~ 264VAC 47 ~ 63Hz PF>0.95/230VAC EFFICIENCY (Typ.) 74% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.5A/115VAC 0.75A/230VAC COLD START ≦40A/230V PF>0.98/115VAC at full load 74% LEAKAGE CURRENT <3.5mA / 240VAC OVERLOAD 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 75% CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V Protection type : Shut down o/p voltage, re-power on to recover 95℃ ± 5℃ (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60℃ (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85℃, 10 ~ 95% RH ± 0.03%/℃ (0~50℃) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A MTBF 139.9K hrs min. MIL-HDBK-217F (25℃) 199*99*50mm (L*W*H) 0.87Kg; 20pcs/18.4Kg/1.28CUFT DIMENSION PACKING NOTE 24ms/115VAC at full load 127 ~ 370VDC POWER FACTOR (Typ.) OVER TEMPERATURE(OPTION) OTHERS 800ms, 50ms/115VAC at full load FREQUENCY RANGE PROTECTION OVER VOLTAGE (Note 4) 100.9W VOLTAGE TOLERANCE Note.3 ± 3.0% VOLTAGE ADJ. RANGE VOLTAGE RANGE EMC 100W RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p HOLD UP TIME (Typ.) SAFETY & QP-100-3C CH1 LINE REGULATION INPUT QP-100-3B OUTPUT NUMBER 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-100-SPEC 2007-10-25 QP-100 100W Quad Output with PFC Function series ■ Features : $Universal AC input / Full range $Built-in active PFC function, PF>0.95 $Protections:Short circuit/Over load/Over voltage $Free air cooling convection $CH4:± Polarity is selectable $Fixed switching frequency at 100KHz $3 years warranty .. SPECIFICATION QP-100-3D MODEL OUTPUT QP-100F CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V 3.3V 24V -12V 5V 12V 24V -12V 5V 15V 24V -15V RATED CURRENT 8A 8A 1.3A 0.6A 8A 2.4A 1A 0.6A 8A 2A 1A 0.6A CURRENT RANGE 2 ~ 10A 0 ~ 10A 0.3 ~ 2A 0 ~ 1A 2 ~ 10A 0 ~ 3A 0.3 ~ 2A 0 ~ 1A 2 ~ 10A 0 ~ 3A 0.3 ~ 2A 0 ~ 1A RATED POWER (max.) 104.8W 100W 103W RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 150mVp-p 150mVp-p 120mVp-p 150mVp-p 200mVp-p 150mVp-p 120mVp-p 180mVp-p 200mVp-p 150mVp-p CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 11.4 ~ 13.2V CH1: 4.75 ~ 5.5V CH2: 14.3 ~ 16.5V VOLTAGE TOLERANCE Note.3 ± 3.0% CH1: 4.75 ~ 5.5V ± 3.0% ± 6.0% ± 5.0% ± 3.0% ± 3.0% ± 6.0% ± 5.0% ± 3.0% ± 3.0% ± 6.0% ± 5.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% ± 1.0% ± 1.0% ± 2.0% ± 1.0% LOAD REGULATION ± 2.0% ± 2.0% ± 6.0% ± 2.0% ± 2.0% ± 2.0% ± 6.0% ± 2.0% ± 2.0% ± 2.0% ± 6.0% ± 2.0% SETUP, RISE TIME 800ms, 50ms/230VAC VOLTAGE ADJ. RANGE LINE REGULATION 24ms/230VAC HOLD TIME (Typ.) VOLTAGE RANGE INPUT QP-100D OUTPUT NUMBER Note.5 90 ~ 264VAC 800ms, 50ms/115VAC at full load 24ms/115VAC at full load 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 75% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.5A/115VAC 0.75A/230VAC COLD START ≦40A/230V LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE(OPTION) WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE PF>0.98/115VAC at full load 78% 78% <3.5mA / 240VAC 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V CH1:5.75 ~ 6.75V CH2:13.8 ~ 16.2V CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover CH2:17.25 ~ 20.25V 95℃ ± 5℃ (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60℃ (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85℃, 10 ~ 95% RH ± 0.03%/℃ (0~50℃) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) OTHERS HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A MTBF 139.9K hrs min. MIL-HDBK-217F (25℃) 199*99*50mm (L*W*H) 0.87Kg; 20pcs/18.4Kg/1.28CUFT DIMENSION PACKING NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-100-SPEC 2007-10-25 s e r i se es r i e s UQSPP- 1- 0202 5 100W Quad Output with PFC Function Mechanical Specification Case No. 916A Unit:mm 199 20 35 133 25 117 70 65 LED +V ADJ.2 +V ADJ.1 49.5 99 119 51 79 2-M4 5-M3 L=6mm 16 10 38 6.15 7.62 10 9 8 7 6 5 4 3 2 1 15 142 25 Terminal Pin No. Assignment : Pin No. Pin No. Assignment Assignment 1 5 AC/L DC OUTPUT V3 2 6,7 AC/N DC OUTPUT V1 3 FG 8,9 DC OUTPUT COM 4 DC OUTPUT V4 10 DC OUTPUT V2 25 12.5 50 25 8 max. 6-M4 L=6mm Block Diagram fosc : 100KHz EMI FILTER & RECTIFIERS I/P POWER SWITCHING PFC CIRCUIT PWM & PFC CONTROL FG RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER V4 REGULATOR V3 RECTIFIERS & FILTER V2 +5V COM DETECTION CIRCUT O.V.P. Derating Curve Output Derating VS Input Voltage 100 100 90 80 80 70 70 LOAD (%) LOAD (%) 60 40 20 -10 -10 0 0 10 20 30 40 50 AMBIENT TEMPERATURE (℃) 60 (HORIZONTAL) 60 50 40 90 110 115 135 155 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-100-SPEC 2007-10-25 QP-100B,C 100W Quad Output with PFC Function series ■ Features : #Universal AC input / Full range #Built-in active PFC function, PF>0.95 #Protections: Short circuit / Overload / Over voltage #Free air cooling convection #Fixed switching frequency at 100KHz #3 years warranty .. SPECIFICATION QP-100B MODEL OUTPUT CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V 12V -12V -5V 5V 15V -15V -5V RATED CURRENT 10A 3A 1A 0.6A 10A 2.2A 1A 0.6A CURRENT RANGE 2 ~ 10A 0.3 ~ 4A 0.15 ~ 1A 0 ~ 1A 2 ~ 10A 0.3 ~ 3A 0.15 ~ 1A 0 ~ 1A RATED POWER (max.) 101W 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p RIPPLE & NOISE (max.) Note.2 100mVp-p VOLTAGE TOLERANCE Note.3 ± 3.0% ± 6.0% +10,-6% ± 5.0% ± 3.0% +6,-10% ± 8.0% ± 5.0% ± 1.0% ± 2.0% ± 2.0% ± 1.0% ± 1.0% ± 2.0% ± 2.0% ± 1.0% LOAD REGULATION ± 2.0% ± 6.0% ± 6.0% ± 2.0% ± 2.0% ± 2.0% ± 6.0% ± 2.0% SETUP, RISE TIME 1000ms, 50ms at full load 24ms at full load Note.5 90 ~ 264VAC 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 76% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.5A/115VAC 0.75A/230VAC COLD START 40A <3.5mA / 240VAC OVERLOAD WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover 95℃ ± 5℃ (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60℃ (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85℃, 10 ~ 95% RH ± 0.03%/℃ (0~50℃) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 HARMONIC CURRENT EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A MTBF 139.9K hrs min. DIMENSION 199*99*50mm (L*W*H) 1.1Kg; 20pcs/22Kg/1.28CUFT PACKING NOTE 77% 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. OTHERS PF>0.98/115VAC at full load LEAKAGE CURRENT OVER TEMPERATURE(OPTION) (Note 4) 127 ~ 370VDC FREQUENCY RANGE PROTECTION OVER VOLTAGE EMC CH1:4.75 ~ 5.5V LINE REGULATION VOLTAGE RANGE SAFETY & 101W CH1:4.75 ~ 5.5V VOLTAGE ADJ. RANGE HOLD UP TIME (Typ.) INPUT QP-100C OUTPUT NUMBER MIL-HDBK-217F (25℃) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-100B,C-SPEC 2007-10-25 QP-100B,C 100W Quad Output with PFC Function Mechanical Specification Case No. 916A series Unit:mm 199 20 35 133 25 117 70 65 LED 99 119 51 79 49.5 2-M4 16 10 38 6.15 7.62 10 +V ADJ.1 9 8 7 6 5 4 5-M3 L=6mm 3 2 1 15 142 25 Terminal Pin No. Assignment : Pin No. Pin No. Assignment Assignment 1 5 AC/L DC OUTPUT V3 2 6,7 DC OUTPUT V1 AC/N 3 8,9 DC OUTPUT COM FG 4 10 DC OUTPUT V2 DC OUTPUT V4 25 12.5 50 25 8 max. 6-M4 L=6mm Block Diagram fosc : 100KHz EMI FILTER & RECTIFIERS I/P POWER SWITCHING PFC CIRCUIT PWM & PFC CONTROL FG RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER V4 REGULATOR V3 RECTIFIERS & FILTER V2 +5V COM DETECTION CIRCUT O.V.P. Derating Curve Output Derating VS Input Voltage 100 100 90 80 80 70 70 LOAD (%) LOAD (%) 60 40 20 -10 -10 0 0 10 20 30 40 50 AMBIENT TEMPERATURE (℃) 60 (HORIZONTAL) 60 50 40 90 110 115 135 155 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-100B,C-SPEC 2007-10-25