S-210 210W Single Output Switching Power Supply series ■ Features : $AC input range selectable by switch $Protections: Short circuit / Overload / Over voltage / Over temperature $100% full load burn-in test $Fixed switching frequency at 90KHz $Low cost $High reliability $2 years warranty SPECIFICATION MODEL OUTPUT INPUT S-210-5 S-210-7.5 S-210-12 S-210-13.5 S-210-15 S-210-24 S-210-27 DC VOLTAGE 5V 7.5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 40A 27A 17A 15A 14A 8.8A 7.8A 4.4A CURRENT RANGE 0 ~ 40A 0 ~ 27A 0 ~ 17A 0 ~ 15A 0 ~ 14A 0 ~ 8.8A 0 ~ 7.8A 0 ~ 4.4A RATED POWER 200W 202.5W 204W 202.5W 210W 211.2W 210.6W 211.2W RIPPLE & NOISE (max.) Note.2 80mVp-p 100mVp-p 120mVp-p 120mVp-p 120mVp-p 200mVp-p 200mVp-p 200mVp-p VOLTAGE ADJ. RANGE 6 ~ 9V ± 2.0% 10 ~ 13.2V ± 1.0% 12 ~ 15V ± 1.0% 13.5 ~ 18V ± 1.0% 20 ~ 26.4V ± 1.0% 26 ~ 29V ± 1.0% 45.6 ~ 52.8V ± 1.0% 4.5 ~ 5.7V VOLTAGE TOLERANCE Note.3 ± 2.0% LINE REGULATION ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% LOAD REGULATION ± 1.0% ± 1.0% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% SETUP, RISE TIME 1000ms, 20ms/230VAC HOLD UP TIME (Typ.) 20ms/230VAC VOLTAGE RANGE 88 ~ 132VAC / 176~264VAC by switch FREQUENCY RANGE 47 ~ 63Hz 85% 87% 87% 87% 20ms/115VAC at full load 79% 4.2A/115VAC 35A/115VAC LEAKAGE CURRENT <3.5mA / 240VAC OVERLOAD 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE MTBF DIMENSION PACKING 82% 248 ~ 370VDC EFFICIENCY (Typ.) OVER TEMPERATURE NOTE 1000ms, 20ms/115VAC at full load AC CURRENT (Typ.) INRUSH CURRENT (Typ.) PROTECTION OVER VOLTAGE OTHERS S-210-48 83% 84% 2.5A/230VAC 50A/230VAC 5.75 ~ 6.75V 9.4 ~ 10.9V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V Protection type : Hiccup mode, recovers automatically after fault condition is removed RTH1≧85℃ 31.05 ~ 36.45V 55.2 ~ 64.8V Protection type : Hiccup mode, recovers automatically after fault condition is removed -20 ~ +50℃ (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85℃, 10 ~ 95% RH ± 0.03%/℃ (0 ~ 50℃) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes UL60950-1 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC 244.7K hrs min. MIL-HDBK-217F (25℃) 215*115*50mm (L*W*H) 0.95Kg; 12pcs/12.4Kg/0.92CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. File Name:S-210-SPEC 2007-10-25 S-210 210W Single Output Switching Power Supply Mechanical Specification Case No. 912E series Unit:mm Air flow 18CFM (5~12V) direction 27.5 177.5 32.5 150 117.5 LED 115 95 50 5-M3 L=3mm 16 10 50.5 4-M4 L=5mm 32.5 9.5 9 8 7 6 5 4 3 2 1 8 135 +V ADJ. 15 215 32.5 150 Terminal Pin No. Assignment : Pin No. 1 2 3 50 CL 25 13 max. Assignment AC/L AC/N FG Pin No. Assignment 4~6 DC OUTPUT -V 7~9 DC OUTPUT +V 6-M4 L=6mm Block Diagram fosc : 90KHz 230 115 ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & FILTER FG O.L.P. RECTIFIERS & FILTER POWER SWITCHING +V -V DETECTION CIRCUIT PWM CONTROL O.V.P. O.T.P. Derating Curve Static Characteristics 15 ~ 48V 18CFM forced air cooling (L=10cm) 5~12V 100 80 75 Natural convection cooling(13.5~48V) 90 80 Natural convection cooling(5~12V) 40 20 -20 0 10 20 5 ~ 13.5V 70 50 LOAD (%) LOAD (%) 60 Ta=25℃ 100 30 40 50 60 (HORIZONTAL) 60 50 40 88 176 100 190 132 264 AMBIENT TEMPERATURE (℃) File Name:S-210-SPEC 2007-10-25