SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER CURRENT • • • 4.4-4.8 3.4-3.8 .1 φ3 -3 . 4 1.5-1.9 0.8-1.0 Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 4) Mounting Torque: 6 in – 1bs max. Weight: 0.15 ounce,4.0 gram 2.8-3.2 17.2-17.8 MECHANICAL DATA • • 24.8-25.2 O 9.3-9.7 3.0×45 3.6 14.7-15.3 Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length 3.3-3.7 • • • • 4.0 Amperes KBJ FEATURES • 50 to 1000 Volts VOLTAGE RANGE KBJ4005G THRU KBJ410G 0.6-0.8 0.9-1.1 7.3-7.7 7.2-7.7 7.3-7.7 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% KBJ SYMBOLS KBJ VRRM VRMS VDC Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward T C=100℃(Note Rectified Current, At TA=40℃(Note Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per leg at 2.0A Maximum DC Reverse Current at rated DC blocking voltage per element TA=25℃ TA=125℃ Typical Junction Capacitance, per let (Note 3) Typical Thermal Resistance (Note 1) Operating Junction Temperature Range Storage Temperature Range 1) 2) KBJ KBJ KBJ KBJ KBJ 4005G 401G 402G 404G 406G 408G 410G 50 35 50 100 70 100 200 140 200 400 280 400 4.0 3.0 600 420 600 800 560 800 1000 700 100 I(AV) UNIT Volts Volts Volts Amps IFSM 120 Amps I2 t 60 A2s VF 1.0 Volts IR 5.0 500 μA CJ RJA TJ TSTG 100.0 45.0 22.0 (-55 to +150) (-55 to +150) Notes: 1. Unit mounted on 1.6×1.6×0.06” thick (4.0×4.0×0.15cm) AL. plate 2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length 3. Measured at 1.0 MHz and applied reverse voltage of 4.0 V 4. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum Heat transfer with #6 screws E-mail: [email protected] Web Site: www.cnmic.com pF ℃/W ℃/W ℃ SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER 50 to 1000Volts VOLTAGE RANGE KBJ4005G THRU KBJ410G CURRENT 4.0 Amperes RATINGS AND CHARACTERISTIC CURVES KBJ4005G THRU KBJ410G FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT 150 Heat-Sink Mounting, Tc 1.6×1.6×0.06"Thk (4.0×4.0×0.15cm) AL. Plate PEAK FORWARD SURGE, CURRENT,(A) AVERAGE FORWARD OUTPUT,CURRENT (A) 4.0 FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 3.0 2.0 1.0 P.C.B. Mounting, TA 0.47×0.47" (12×12mm) Copper pads 0.375"(9.5mm) lead length 60 Hz Resistive or Inductive Load 50 0 50 100 10 1 150 100 TEMPERATURE, ℃ NUMBER OF CYCLES AT 60 Hz FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE FIG. 4- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 500 INSTANTANEOUS REVERSE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 100 1.0 CYCLE 0 0 10 TJ=25℃ Pulse width=300μ 1% Duty Cycle 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 50-400V 600-1000V 100 T J =125℃ 10 1 0.1 0.01 1.6 T J =25℃ 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(V) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE 100 1000 T j =25℃ f=1.0MHz Vsig=50mVp-p TRANSIENT THERMAL IMPEDANCE (℃/W) JUNCTION CAPACITANCE, (pF) TJ = T J max. Single Sine-Wave (JEDEC Method) 100 50-400V 600-1000V 10 0.1 1 10 1 0.1 10 100 0.01 0.1 REVRESE VOLTAGE,(V) E-mail: [email protected] 1 10 T, HEATING TIME (SEC.) Web Site: www.cnmic.com 100