SINGLE-PHASE GLASS PASSIVATED BRIDGE RECTIFIER CURRENT 4.0 Amperes FEATURES + 1.9 - 2.5 ~ ~ 2.03 - 2.41 0.9 - 1.1 • • Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any Weight: 0.071 ounce,2.0 gram 4.8 - 5.3 0.46 - 0.56 0.80 - 1.08 MECHANICAL DATA • • ~ 10.4 - 10.7 O 17 - 18.2 • 20.7×45 1.5 - 2.03 • • • • 20.7 - 20.9 Plastic package has Underwriters Laboratory Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength High surge current capability Ideal for printed circuit boards High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length,5 lbs. (2.3kg) tension 3.25 - 3.56 • 50 to 1000 Volts VOLTAGE RANGE GBLA005 THRU GBLA10 Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% GBLA GBLA SYMBOLS 01 005 Maximum Reverse Peak Repetitive Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Output Current, At T C=50℃ TA=40℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per Bridge element 4.0A TA=25℃ Maximum Reverse Current at rated DC blocking voltage per element TA=125℃ Typical Junction Capacitance per leg (Note 3) Typical Thermal Resistance (Note 1) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range I(AV) GBLA 02 200 140 200 GBLA GBLA GBLA GBLA 04 400 280 400 4.0(Note 1) 3.0(Note 2) 06 600 420 600 08 800 560 800 10 1000 700 1000 UNIT Volts Volts Volts Amps IFSM 120 Amps I2 t 60 A2s VF 1.0 Volts IR 5.0 500 μA CJ RJA RJL TJ ,TSTG 95.0 40.0 22 10 (-55 to +150) Notes: 1. Unit mounted on 3.0×3.0×0.11” thick (7.5×7.5×0.3cm) AL. plate 2. Unit mounted on P.C.B. at 0.375” (9.5mm) lead lengh and 0.5×0.5”(12×12mm) copper pads 3. Measured at 1.0MHz and applied reverse voltage of 4.0 V Web Site: www.hkmic.com pF ℃/W ℃/W ℃ SINGLE-PHASE GLASS PASSIVATED BRIDGE RECTIFIER 50 to 1000Volts VOLTAGE RANGE GBLA005 THRU GBLA10 CURRENT 4.0 Ampere RATINGS AND CHARACTERISTIC CURVES GBLA005 THRU GBLA10 FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 5.0 150 60 Hz Resistive or Inductive Load PEAK FORWARD SURGE, CURRENT, (A) AVERAGE FORWARD OUTPUT,CURRENT (A) FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT Heat- SinkMounting 3.0×3.0×0.11"Thick (7.5×7.5×0.3cm ) Aluminum Plate 4.0 3.0 2.0 P.C.B. Mounting 0.47×0.47"( 12×12mm) Copper pads with 0.375" (9.5mm) lead length 1.0 TJ = T J max. Single Sine-Wave (JEDEC Method) 100 50 1.0 CYCLE 0 0 100 50 0 150 FIG. 4- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 500 INSTANTANEOUS REVERSE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 100 NUMBER OF CYCLES AT 60 Hz FIG. 3- TYPICAL FORWORD VOLTAGE CHARACTERISTICS PER LGE 10 1 0.1 TJ=25℃ Pulse width=300 μs 1% Duty Cycle 0.4 0.6 0.8 1.0 1.2 1.4 100 10 0.1 0.01 1.6 60 40 80 100 100 TRANSIENT THERMAL IMPEDANCE (℃/W) T j =25℃ f=1.0MHz Vsig=50mVp-p 100 50-400V 600-1000V 10 20 FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG 1000 1 0 PERCENT OF RATED PEAK REVERSE VOLTAGE,(V) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG 0.1 50-400V 600-1000V 1 INSTANTANEOUS FORWARD VOLTAGE,(V) 10 TA =125℃ TA =25℃ 0.01 JUNCTION CAPACITANCE, (pF) 10 1 AMBIENT TEMPERATURE, ℃ 10 1 0.1 100 REVRESE VOLTAGE,(V) Web Site: www.hkmic.com 0.01 0.1 1 10 T, HEATING TIME (SEC.) 100