PRESS FIT AUTOMOTIVE RECTIFIER (LUCAS) LPR501 THRU LPR506 VOLTAGE RANGE 100 to 600 Volts CURRENT 50.0 Amperes LC-1 TECHNICAL SPECIFICATION： 0.050± 0.002 (Φ1.28±0.05) FEATURES • • • • Low Leakage Low forward voltage drop High current capability High forward surge current capacity 0.333 8.45MAX MECHANICAL DATA • • • • • • Positive 0.872± 0.01 21.00± 0.26 Negative 1.02± 0.01 26.00± 0.26 0.133-0.149 (3.40-3.80) 0.39(9.95) Technology: Glass passivated chip with vacuum soldered Case: Copper case Polarity: As marked of case bottom Lead: Plated lead , solderable per MIL-STD-202E method 208C Mounting: Press Fit Weight: 0.23 ounces, 6.58 grams 0.397-0.399 10.09-10.15 Epoxy Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60HZ, resistive or inductive load For capacitive load derate current by 20% SYMBOLS LPR501 Maximum Repetitive Peak Reverse Voltage VRRM 100 200 300 400 600 Volts Maximum RMS Voltage VRMS 70 140 210 280 420 Volts Maximum DC Blocking Voltage VDC 100 200 300 400 600 Volts Maximum Average Forward Rectified Current, LPR502 LPR503 LPR504 LPR506 UNIT I(AV) 50 Amps IFSM 600 Amps Rating for fusing (t＜8.3ms) I2t 1494 A2S Maximum instantaneous Forward Voltage at 100A VF 1.05 Volts At Tc=105℃ Peak Forward Surge Current 3.3mS single half sine wave superimposed on Rated load (JEDEC method) Maximum DC Reverse Current at Rated TA=25℃ DC Blocking Voltage TA=100℃ 0.8 ℃/W TJ,TSTG (-65 to +175) ℃ Notes: 1. UA 450 RθJC Typical Thermal Resistance Operating and Storage Temperature Range 5.0 IR Enough heatsink must be considered in application. E-mail: [email protected] Web Site: www.cnmic.com PRESS FIT AUTOMOTIVE RECTIFIER (LUCAS) LPR501 THRU LPR506 VOLTAGE RANGE 100 to 600 Volts CURRENT 50.0 Amperes RATINGS AND CHARACTERISTIC CURVES LPR501 THRULPR506 F1G.2 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 PEAK FORWARD SURGE CURRENT,(A) AVERAGE FORWARD CURRENT, (A) F1G.1 TYPICAL FORWARD CURRENT DERATING GURVE 40 30 Single Phase 20 Half Wave 60Hz Resistive or Inductive Load 10 0.375″(9.5mm) Lead Length 600 8.3ms Single Half Sine-Wave 500 (JEDEC Method) Tj=Tj max 400 300 200 100 0 1 Cycle 0 25 50 75 100 125 150 175 1 AMBIENT TEMPERATURE, (℃) 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60 Hz F1G.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS F1G.4 FORWARD ROWER DISSIPATION AVERAGE POWER DISSIPATION (W) INSTANTANEOUS FORWARD CURRENT, (A) 1000 100 10 T1=25℃ PULSE WIDTH=300μS 1%DUTY CYCLE 50 SQUARE WAVE DC 30 0 0 1.0 0.1 0.6 80 20 30 40 50 AVERAGE FORWARD CURRENT, (A) 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE,(V) E-mail: [email protected] Web Site: www.cnmic.com 60