ADS-939 16-Bit, 10MHz Sampling A/D Converters PRELIMINARY DATA FEATURES N 16-bit resolution N 10MHz sampling rate N Functionally complete N No missing codes over full military temperature range N Edge-triggered N ±5V, ±12V or ±15V supplies, 1.5 Watts N Small, 40-pin, ceramic TDIP N 82dB SNR, –86dB THD N Ideal for both time and frequency-domain applications INPUT/OUTPUT CONNECTIONS GENERAL DESCRIPTION The ADS-939 is a 16-bit, 10MHz sampling A/D converter. This device accurately samples full-scale input signals up to Nyquist frequencies with no missing codes. The dynamic performance of the ADS-939 has been optimized to achieve a signal-to-noise ratio (SNR) of 82dB and a total harmonic distortion (THD) of –86dB. Packaged in a 40-pin TDIP, the functionally complete ADS-939 contains a fast-settling sample-hold amplifier, a subranging (two-pass) A/D converter, an internal reference, timing/control logic, and error-correction circuitry. Digital input and output levels are TTL. The ADS-939 only requires the rising edge of the start convert pulse to operate. Requiring ±5V supplies and either ±12v or ±15V supplies the ADS-939 dissipates 3.0 Watts. The device is offered with a bipolar (±2.75V) or a unipolar (0 to –5.5V) analog input range. Models are available for use in either commercial (0 to +70°C) or military (–55 to +125°C) operating temperature ranges. A proprietary, auto-calibrating, error-correcting circuit enables the device to achieve specified performance over the full military temperature range. Typical applications include medical imaging, radar, sonar, communications and instrumentation. PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 +3.2V REF. OUT UNIPOLAR ANALOG INPUT ANALOG GROUND OFFSET ADJUST GAIN ADJUST DIGITAL GROUND NC NC NC NC START CONVERT BIT 16 (LSB) BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 +12V/+15V –12V/–15V +5V ANALOG SUPPLY –5V SUPPLY ANALOG GROUND COMP. BITS OUTPUT ENABLE OVERFLOW EOC +5V DIGITAL SUPPLY DIGITAL GROUND BIT 1 (MSB) BIT 1 (MSB) BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 10 FSTAT1 11 FSTAT2 POWER AND GROUNDING GAIN ADJUST 6 38 37 ANALOG GROUND 4, 36 DIGITAL GROUND 7, 30 –12/–15V ANALOG SUPPLY +12/+15V ANALOG SUPPLY 39 40 28 BIT 1 (MSB) +3.2V REF. OUT 1 PRECISION +3.2V REFERENCE POWER AND GROUNDING +5V ANALOG SUPPLY 38 +5V DIGITAL SUPPLY 31 –5V SUPPLY 37 ANALOG GROUND 2, 4, 36 DIGITAL GROUND 7, 30 NO CONNECTION 39, 40 OFFSET ADJUST 5 OFFSET ADJUST CKT. UNIPOLAR 2 ANALOG INPUT 3 S/H 27 BIT 2 26 BIT 3 25 BIT 4 3-STATE OUTPUT REGISTER 31 –5V SUPPLY 9 FIFO/READ 29 BIT 1 (MSB) CUSTOM GATE ARRAY +5V DIGITAL SUPPLY 8 FIFO/DIR 2-PASS ANALOG-TO-DIGITAL CONVERTER +5V ANALOG SUPPLY GAIN ADJUST CKT. 24 BIT 5 23 BIT 6 22 BIT 7 21 BIT 8 20 BIT 9 19 BIT 10 18 BIT 11 17 BIT 12 16 BIT 13 15 BIT 14 14 BIT 15 13 BIT 16 (LSB) START CONVERT 12 EOC 32 For full details go to www.murata-ps.com/rohs 34 OUTPUT ENABLE TIMING AND CONTROL LOGIC 33 OVERFLOW COMP. BITS 35 Figure 1. ADS-939 Functional Block Diagram www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 1 of 7 ADS-939 16-Bit, 10MHz Sampling A/D Converters ABSOLUTE MAXIMUM RATINGS PARAMETERS +5V Supply (Pins 31, 38) –5V Supply (Pin 37) +12V/+15V Supply (pin 40) –12V/–15V Supply (pin 39) Digital Inputs (Pins 8, 9, 12, 34, 35) Analog Input (Pin 3) Lead Temperature (10 seconds) PHYSICAL/ENVIRONMENTAL LIMITS UNITS 0 to +6 0 to –6 0 to +16V 0 to +16V –0.3 to +VDD +0.3 ±5 +300 Volts Volts Volts Volts Volts Volts °C PARAMETERS MIN. TYP. MAX. UNITS 0 –55 — — +70 +125 °C °C Operating Temp. Range, Case ADS-939MC ADS-939MM Thermal Impedance Qjc Qca Storage Temperature Range Package Type Weight — — –65 4 — °C/Watt 18 — °C/Watt — +150 °C 40-pin, metal-sealed, ceramic TDIP 0.56 ounces (16 grams) FUNCTIONAL SPECIFICATIONS (TA = +25°C, ±VCC = ±12/15V, +VDD = ±5V, 10MHz sampling rate, and a minimum 3 minute warm-up ~ unless otherwise specified.) +25°C ANALOG INPUT Input Voltage Range Unipolar Bipolar Input Resistance (Pin 3) (Pin 2) Input Capacitance MIN. TYP. 0 to +70°C MAX. MIN. –55 to +125°C TYP. MAX. MIN. TYP. MAX. UNITS — — — — — 0 to –5.5V ±2.75 400 480 10 — — — — 15 — — — — — 0 to –5.5V ±2.75 400 480 10 — — — — 15 — — — — — 0 to –5.5V ±2.75 400 480 10 — — — — 15 Volts Volts 7 7 pF +2.0 — — — 20 — — — — 50 — +0.8 +20 –20 — +2.0 — — — 20 — — — — 50 — +0.8 +20 –20 — +2.0 — — — 20 — — — — 50 — +0.8 +20 –20 — Volts Volts μA μA ns — — –0.95 — — — — 16 16 ±1 ±0.5 ±0.15 ±0.1 ±0.1 ±0.15 — — — +1.0 ±0.3 ±0.2 ±0.2 ±0.3 — — — –0.95 — — — — 16 16 ±1.5 ±0.5 ±0.3 ±0.2 ±0.2 ±0.3 — — — +1.0 ±0.5 ±0.4 ±0.4 ±0.5 — — — –0.95 — — — — 16 16 ±2 ±0.5 ±0.5 ±0.4 ±0.4 ±0.5 — — — +1.5 ±0.8 ±0.6 ±0.6 ±0.8 — Bits LSB LSB %FSR %FSR %FSR % Bits — — –87 –82 TBD TBD — — –87 –82 TBD TBD — — –82 –78 TBD TBD dB dB — — –86 –81 TBD TBD — — –86 –81 TBD TBD — — –81 –77 TBD TBD dB dB TBD TBD 86 85 — — TBD TBD 86 85 — — TBD TBD 80 80 — — dB dB TBD TBD — 82 81 80 — — — TBD TBD — 82 81 80 — — — TBD TBD — 78 75 80 — — — dB dB μVrms — –87 –85 — –87 –85 — –87 –82 dB — — 25 15 — — — — 25 25 — — — — 25 15 — — MHz MHz — — — — 90 ±400 4 0.2 — — — — — — — — 90 ±400 4 0.2 — — — — — — — — 90 ±400 4 0.2 — — — — dB V/μs ns ps rms — — 10 40 100 — — — — — — 10 40 100 — — — — — — 10 45 100 — — — — ns ns MHz DIGITAL INPUTS Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Start Convert Positive Pulse Width STATIC PERFORMANCE Resolution Integral Nonlinearity Differential Nonlinearity (fin = 10kHz) Full Scale Absolute Accuracy Bipolar Zero Error (Tech Note 2) Bipolar Offset Error (Tech Note 2) Gain Error (Tech Note 2) No Missing Codes (fin = 10kHz) DYNAMIC PERFORMANCE Peak Harmonics (–3dB) dc to 500kHz 500kHz to 5MHz Total Harmonic Distortion (–3dB) dc to 500kHz 500kHz to 5MHz Signal-to-Noise Ratio (w/o distortion, –3dB) dc to 500kHz 500kHz to 5MHz Signal-to-Noise Ratio (& distortion, –3dB) dc to 500kHz 500kHz to 5MHz Noise Two-Tone Intermodulation Distortion (fin = 200kHz, 240kHz, fs = 10MHz, –3dB) Input Bandwidth (–3dB) Small Signal (–20dB input) Large Signal (–0.5dB input) Feedthrough Rejection (fin = 1MHz) Slew Rate Aperture Delay Time Aperture Uncertainty S/H Acquisition Time ( to ±0.001%FSR, 5.5V step) Overvoltage Recovery Time A/D Conversion Rate www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 2 of 7 ADS-939 16-Bit, 10MHz Sampling A/D Converters DYNAMIC PERFORMANCE (Cont.) MIN. +25°C TYP. MAX. MIN. 0 TO +70°C TYP. MAX. — — — +3.2 ±30 5 — — — — — — +3.2 ±30 5 — — — MIN. –55 TO +125°C TYP. MAX. UNITS ANALOG OUTPUT Internal Reference Voltage Drift External Current — — — +3.2 ±30 5 — — — Volts ppm/°C mA DIGITAL OUTPUTS Logic Levels Logic "1" Logic "0" Logic Loading "1" Logic Loading "0" Output Coding +2.4 — — +2.4 — — +2.4 — — — — +0.4 — — +0.4 — — +0.4 — — –4 — — –4 — — –4 — — +4 — — +4 — — +4 (Offset) Binary / Complementary (Offset) Binary / Two's Complement / Complementary Two's Complement Volts Volts mA mA Power Supply Ranges +5V Supply –5V Supply +12V Supply –12V Supply +15V Supply –15V Supply +4.75 –4.75 +11.5 –11.5 +14.5 –14.5 +5.0 –5.0 +12.0 –12.0 +15.0 –15.0 +5.25 –5.25 +12.5 –12.5 +15.5 –15.5 +4.75 –4.75 +11.5 –11.5 +14.5 –14.5 +5.0 –5.0 +12.0 –12.0 +15.0 –15.0 +5.25 –5.25 +12.5 –12.5 +15.5 –15.5 +4.9 –4.9 +11.5 –11.5 +14.5 –14.5 +5.0 –5.0 +12.0 –12.0 +15.0 –15.0 +5.25 –5.25 +12.5 –12.5 +15.5 –15.5 Volts Volts Volts Volts Volts Volts Power Supply Currents +5V Supply –5V Supply –12/15V Supply +12/15V Supply Power Dissipation Power Supply Rejection — — — — — — +50 –36 –25 +70 1.5 — — — — — TBD ±0.07 — — — — — — TBD TBD TBD TBD TBD — — — — — TBD ±0.07 — — — — — — TBD TBD TBD TBD TBD — — — — — TBD ±0.07 mA mA mA mA Watts %FSR/%V POWER REQUIREMENTS Footnotes: ~ All power supplies must be on before applying a start convert pulse. All supplies and the clock (START CONVERT) must be present during warm-up periods. The device must be continuously converting during this time. This is the time required before the A/D output data is valid once the analog input is back within the specified range. When COMP. BITS (pin 35) is low, logic loading "0" will be –350μA. A 10MHz clock with a 50nsec positive pulse width is used for all production testing. See Timing Diagram for more details. The minimum supply voltages of +4.9V and –4.9V for ±VDD are required for –55°C operation only. The minimum limits are +4.75V and –4.75V when operating at +125°C. Effective bits is equal to: ±12V only or ±15V only required. (SNR + Distortion) – 1.76 + 20 log Full Scale Amplitude See table 2a, Setting Output Coding Selection. Actual Input Amplitude 6.02 TECHNICAL NOTES 1. Obtaining fully specified performance from the ADS-939A requires careful attention to pc-card layout and power supply decoupling. The device's analog and digital ground systems are connected to each other internally. For optimal performance, tie all ground pins (4, 7, 30 and 36) directly to a large analog ground plane beneath the package. For the best performance it is recommended to use a single power source for both the +5V analog and +5V digital supplies. Bypass all power supplies and the +3.2V reference output to ground with 4.7μF tantalum capacitors in parallel with 0.1μF ceramic capacitors. Locate the bypass capacitors as close to the unit as possible. 2. The ADS-939A achieves its specified accuracies without the need for external calibration. If required, the device's small initial offset and gain errors can be reduced to zero using the adjustment circuitry shown in Figure 2. When using this circuitry, or any similar offset and gain calibration hardware, make adjustments following warm-up. To avoid interaction, always adjust offset before gain. Tie pins 5 and 6 to ANALOG GROUND (pin 4) if not using offset and gain adjust circuits. 3. Pin 35 (COMP. BITS) is used to select the digital output coding format of the ADS-939A. See Tables 2a and 2b. When this pin has a TTL logic "0" applied, it complements all of the ADS-939A’s digital outputs. When pin 35 has a logic "1" applied, the output coding is comple- 4. 5. 6. 7. www.murata-ps.com mentary (offset) binary. Applying a logic "0" to pin 35 changes the coding to (offset) binary. Using the MSB output (pin 29) instead of the MSB output (pin 28) changes the respective output codings to complementary two's complement and two's complement. Pin 35 is TTL compatible and can be directly driven with digital logic in applications requiring dynamic control over its function. There is an internal pull-up resistor on pin 35 allowing it to be either connected to +5V or left open when a logic "1" is required. To enable the three-state outputs, connect OUTPUT ENABLE (pin 34) to a logic "0" (low). To disable, connect pin 34 to a logic "1" (high). Applying a start convert pulse while a conversion is in progress (EOC = logic "1") will initiate a new and probably inaccurate conversion cycle. Data from both the interrupted and subsequent conversions will be invalid. Do not enable/disable or complement the output bits or read from the FIFO during the conversion process (from the rising edge of EOC to the falling edge of EOC). The OVERFLOW bit (pin 33) switches from 0 to 1 when the input voltage exceeds that which produces an output of all 1’s or when the input equals or exceeds the voltage that produces all 0’s. When COMP BITS is activated, the above conditions are reversed. Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 3 of 7 ADS-939 16-Bit, 10MHz Sampling A/D Converters CALIBRATION PROCEDURE Connect the converter per Figure 2. Any offset/gain calibration procedures should not be implemented until the device is fully warmed up. To avoid interaction, adjust offset before gain. The ranges of adjustment for the circuits in Figure 2 are guaranteed to compensate for the ADS-939’s initial accuracy errors and may not be able to compensate for additional system errors. A/D converters are calibrated by positioning their digital outputs exactly on the transition point between two adjacent digital output codes. This is accomplished by connecting 6 n6 /&&3%4 !$*534 '!). !$*534 6 & & /6%2&,/7 & %/# 6 & ")4-3" 6$)')4!, ")4-3" ")4 & $)')4!,'2/5.$ ")4 ")4 ")4 6 & & 6!.!,/' ")4 ")4 & n6 ")4 !.!,/''2/5.$ & n6 %.!",% &)&/$)2 &34!4 ")4 ")4 ")4 !$3 ")4 ")4 ")4 ")4 ")4,3" !.!,/').054 &34!4 62%&/54 6 &)&/2%!$ & #/-0")43 #ONNECTFOR 5NIPOLAR-ODEL TOn6 Zero/Offset Adjust Procedure 1. Apply a train of pulses to the START CONVERT input (pin 12) so that the converter is continuously converting. 2. For zero/offset adjust, apply –42μV to the ANALOG INPUT (pin 3). 3. For bipolar operation - Adjust the offset potentiometer until the code flickers between 1000 0000 0000 0000 and 0111 1111 1111 1111 with pin 35 tied high (complementary offset binary) or between 0111 1111 1111 1111 and 1000 0000 0000 0000 with pin 35 tied low (offset binary). For unipolar operation - Adjust the offset potentiometer until all outputs are 1's and the LSB flickers between 0 and 1 with pin 35 tied high (complementary binary) or until all outputs are 0's and the LSB flickers between 0 and 1 with pin 35 tied low (binary). 4. For bipolar, Two's complement coding requires using BIT 1 (MSB) (pin 29). With pin 35 tied low, adjust the trimpot until the output code flickers between all 0’s and all 1’s. 34!24#/.6%24 & Gain adjusting is accomplished when the analog input is at nominal full scale minus 1½ LSB's (+2.749874V or –5.499874V). nn6 & n6 6 For the ADS-939, offset adjusting is normally accomplished when the analog input is 0 minus ½ LSB (–42μV). See Table 2b for the proper bipolar output coding. Note: Connect pin 5 to ANALOG GROUND (pin 4) for operation without zero/offset adjustment. Connect pin 6 to pin 4 for operation without gain adjustment. K 7 K 7 LED's to the digital outputs and performing adjustments until certain LED's "flicker" equally between on and off. Other approaches employ digital comparators or microcontrollers to detect when the outputs change from one code to the next. 5.)0/,!2 &OR"IPOLAR Gain Adjust Procedure Figure 2. Connection Diagram Table 2a. Setting Output Coding Selection (Pin 35) OUTPUT FORMAT PIN 35 LOGIC LEVEL Complementary (Offset) Binary 1 (Offset) Binary 0 Complementary Two’s Complement (Using MSB, pin 29) 1 Two’s Complement (Using MSB, pin 29) 0 1. For gain adjust, for bipolar apply +2.749874V and for unipolar mode 5.499874V to the ANALOG INPUT (pin 3). 2. Adjust the gain potentiometer until all output bits are 0’s and the LSB flickers between a 1 and 0 with pin 35 tied high (complementary (offset) binary) or until all output bits are 1’s and the LSB flickers between a 1 and 0 with pin 35 tied low ((offset) binary). 3. For bipolar, Two's complement coding requires using BIT 1 (MSB) (pin 29). With pin 35 tied low, adjust the gain trimpot until the output code flickers equally between 0111 1111 1111 1111 and 0111 1111 1111 1110. 4. To confirm proper operation of the device, vary the applied input voltage to obtain the output coding listed in Table 2b. www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 4 of 7 ADS-939 16-Bit, 10MHz Sampling A/D Converters Table 2b. Output Coding COMP. BINARY BINARY COMP. TWO'S COMP. INPUT RANGE UNIPOLAR MSB LSB MSB LSB 0 to –5.5V SCALE 0 –1 LSB –0.000084 1111 1111 1111 1111 0000 0000 0000 0000 LSB "1" to "0" LSB "0" to "1" 0 –1 1/2 LSB –0.000126 0 – 1/8 FS –0.687500 1110 0000 0000 0000 0001 1111 1111 1111 0 – 1/4 FS –1.375000 1100 0000 0000 0000 0011 1111 1111 1111 –1/2 FS – 1/2LSB –2.749958 1000 0000 0000 0000 0111 1111 1111 1111 –1/2 LSB –2.750000 0111 1111 1111 1111 1000 000 000 0000 –3/4 FS –4.125000 0100 0000 0000 0000 1011 1111 1111 1111 –7/8 FS –4.812500 0010 0000 0000 0000 1101 1111 1111 1111 –FS +1 LSB –5.499916 0000 0000 0000 0001 1111 1111 1111 1110 LSB "0" to "1" LSB "1" to "0" –FS + 1/2 LSB –5.499958 –FS –5.500000 0000 0000 0000 0000 1111 1111 1111 1111 OFFSET BINARY COMP. OFF. BIN. MSB LSB 0111 1111 1111 1111 LSB "1" to "0" 0110 0000 0000 0000 0100 0000 0000 0000 0000 0000 0000 0000 1111 1111 1111 1111 1100 0000 0000 0000 1010 0000 0000 0000 1000 0000 0000 0001 LSB "0" to "1" 1000 0000 0000 0000 TWO'S COMP. TWO'S COMP. INPUT RANGE BIPOLAR ±2.75V SCALE +2.749916 +FS –1 LSB +2.749874 +FS –1 1/2 LSB +2.062500 +3/4 FS +1.375000 +1/2 FS 0.000000 0 –0.000084 –1 LSB –1.375000 –1/2 FS –2.062500 –3/4 FS –2.749916 –FS +1 LSB –2.749958 –FS + 1/2 LSB –2.750000 –FS MSB LSB 1000 0000 0000 0000 LSB "0" to "1" 1001 1111 1111 1111 1011 1111 1111 1111 1111 1111 1111 1111 0000 0000 0000 0000 0011 1111 1111 1111 0101 1111 1111 1111 0111 1111 1111 1110 LSB "1" to "0" 0111 1111 1111 1111 COMP. TWO'S COMP. THERMAL REQUIREMENTS All DATEL sampling A/D converters are fully characterized and specified over operating temperature (case) ranges of 0 to +70°C and –55 to +125°C. All room-temperature (TA = +25°C) production testing is performed without the use of heat sinks or forced-air cooling. Thermal impedance figures for each device are listed in their respective specification tables. These devices do not normally require heat sinks, however, standard precautionary design and layout procedures should be used to ensure devices do not overheat. The ground and power planes beneath the package, as well as all pcb signal runs to and from the device, should be as heavy as possible to help conduct heat away from the package. Electrically insulating, thermally-conductive "pads" may be installed underneath the package. Devices should be soldered to boards rather than "socketed", and of course, minimal air flow over the surface can greatly help reduce the package temperature. In more severe ambient conditions, the package/junction temperature of a given device can be reduced dramatically (typically 35%) by using one of DATEL's HS Series heat sinks. See Ordering Information for the assigned part number. See page 1-183 of the DATEL Data Acquisition Components Catalog for more information on the HS Series. Request DATEL Application Note AN-8, "Heat Sinks for DIP Data Converters," or contact DATEL directly, for additional information. Scale is approximately 25ns per division. fs = 10MHz START CONVERT N+2 N+1 N N+4 N+3 N+5 N+7 N+6 N+8 50ns 5ns typ. INTERNAL S/H 35ns 65ns 60ns 10ns typ. EOC 40ns 20ns typ. OUTPUT DATA N-8 N-7 N-6 N-5 N-4 N-3 N-2 N-1 N 20ns typ. Figure 3. ADS-939 Timing Diagram www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 5 of 7 www.murata-ps.com 7 14 B1 SG4 SG3 SG2 SG1 26 24 22 20 18 16 14 12 10 8 6 4 2 50 R6 P2 3 2 0.1μF 3 2 J1 4 7 2 6 5 AGND C13 2.2μF AGND C11 2.2μF L1 1 SG5 20mH L4 20mH L3 20mH L2 +5VA –5VA +5VD +5VF AGND 2 AGND OFFSET ADJUST AGND C2 2.2μF C1 2.2μF 20mH 3.3k R3 C9 2.2μF DGND 2.2μF C7 DGND C10 1 33pF 2 1 74HCT74 U1 4 +5VF 6 R2 +15V DGND +5VA –15V –5VA +5VD 3 2 1 DGND DGND C6 2.2μF +5VF 25 23 21 19 17 15 13 11 9 7 5 3 1 AR1 C5 DGND START CONVERT 7 10MHZ 8 1 X1 13 8 9 14 74HCT74 U1 10 DGND 11 12 AGND DGND 2 AGND +5VF B2 ANALOG INPUT AMPLIFIER OPTION AGND R1 3 1 –5VA R4 20k +5VA DGND SG9 RD FIF 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 B9 B10 B11 B12 B13 B14 B15 LSB START FSTAT2 FSTAT1 READ UUT U6 2 3 1 –5VA R5 20k +5VA GAIN ADJUST +5VF DGND 38 39 40 12 13 3 EOC AB8 AB7 AB6 AB5 AB4 AB3 AB2 AB1 +5VD COMP 3 FST1 7 74HC86 U5 14 74HC86 8 U5 FST2 U5 DGND +5VF 9 10 2 1 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 –5VA +5VA DGND C15 0.1μF 74HC86 B8 B7 B6 B5 B4 B3 B2 MSB MSB DGND +5VD EOC OF ENABLE COMP AGND 36 -5VA 37 +5VA –12/–15V +12/+15V C4 2.2μF ADS-939 FIFO/DIR DGND GAIN OFFSET AGND ANA IN AGND +3.2VREF AGND C3 0.1μF 74HC86 4 U5 6 START CONVERT 5 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 –15V –5VA +15V SG6 SG8 SG7 +5VA AB2 AB1 C16 0.1μF AB8 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 DGND C8 0.1μF +5VF DGND C17 0.1μF +5VF AB7 AB6 AB5 AB4 DGND AB3 +5VF 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 U2 10 U3 10 1 U4 10 1 11 1 74HCT573 20 11 74HCT573 20 11 74HCT573 20 DGND 19 18 17 16 15 14 13 12 19 18 17 16 15 14 13 12 B9 B10 B11 B12 B13 B14 B15 +5VD FIF RD DGND COMP START B16 (LSB) B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1(MSB) AGND DGND 1 3 5 7 9 1 2 3 1 2 3 1 2 3 J5 J4 J3 FIFO/DIR READ COMPLIM ENABLE FST2 FST1 FIF/DIR N.C. READ COMPLIM ENABLE DGND DGND DGND DGND DGND DGND DGND EOC OVRFLW 1 2 3 J2 2 4 6 8 10 12 11 14 13 16 15 18 17 P1 20 19 22 21 24 23 26 25 28 27 30 29 32 31 B1B MSB DGND AGND C21 2.2μF +5VA C12 2.2μF –5VA AGND C14 2.2μF +5VD 34 33 C20 0.1μF +5VA C19 0.1μF –5VA AGND DGND 0.1μF 0.1μF C18 0.1μF +5VD B16 (LSB) DGND B8 B7 B6 B5 B4 B3 B2 B1 (MSB) DGND 19 B1B MSB 18 OVRFLW 17 16 15 14 13 12 ADS-939 16-Bit, 10MHz Sampling A/D Converters Preliminary Evaluation Board - Modified ADS-B933 to include ±12V or ±15V Supplies to U6 Figure 4. ADS-939 Evaluation Board Schematic. Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 6 of 7 ADS-939 16-Bit, 10MHz Sampling A/D Converters MECHANICAL DIMENSIONS INCHES (mm) 2.12/2.07 (53.85/52.58) 40 Dimension Tolerances (unless otherwise indicated): 2 place decimal (.XX) ±0.010 (±0.254) 3 place decimal (.XXX) ±0.005 (±0.127) 21 Lead Material: Kovar alloy 1.11/1.08 (28.20/27.43) 1 Lead Finish: 50 microinches (minimum) gold plating over 100 microinches (nominal) nickel plating 20 0.100 TYP. (2.540) 1.900 ±0.008 (48.260) 0.245 MAX. (6.223) PIN 1 INDEX ( ON TOP) 0.200/0.175 (5.080/4.445) 0.015/0.009 (0.381/0.229) 0.210 MAX. (5.334) 0.018 ±0.002 (0.457) 0.110/0.090 (2.794/2.286 0.900 ±0.010 (22.86) 0.110/0.090 (2.794/2.286) SEATING PLANE 0.035/0.015 (0.889/0.381) 0.045/0.035 (1.143/0.889) ORDERING INFORMATION MODEL ADS-939MC ADS-939MM OPERATING TEMP. RANGE 0 to +70°C –55 to +125°C ACCESSORIES ADS-B939 HS-40 Evaluation Board (without ADS-939) Heat Sink for all ADS-939 models Receptacles for PC board mounting can be ordered through AMP, Inc., Part # 3-331272-8 (Component Lead Socket), 40 required. For MIL-STD-883 product, or surface mount packaging, contact DATEL. USA: Mansfield (Ma), Tel: (508) 339-3000, email: [email protected] Canada: Toronto, Tel: (866) 740 1232, email: [email protected] Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: [email protected] ISO 9001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. www.murata-ps.com UK: Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected] France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected] Germany: München, Tel: +49 (0)89-544334-0, email: [email protected] Japan: Tokyo, Tel: 3-3779-1031, email: [email protected] Osaka, Tel: 6-6354-2025, email: [email protected] Website: www.murata-ps.jp China: Shanghai, Tel: +86 215 027 3678, email: [email protected] Guangzhou, Tel: +86 208 221 8066, email: [email protected] Technical enquiries email: [email protected], tel: +1 508 339 3000 MDA_ADS-939.A01 Page 7 of 7