Multi-rate OC-48/STM-16 LR-2/L-16.2 SFP CWDM Transceivers with Digital Diagnostics TRPA48L2M CWDM Product Description The TRPA48L2M CWDM SFP series of multi-rate fiber optic transceivers with digital diagnostics monitoring functionality provide a quick and reliable interface for long reach (LR-2) applications. Diagnostics monitoring functionality (alarm and warning features) is integrated into the design via an I2C serial interface per the Multi-Source Agreement (MSA) SFF-8472, Rev. 9.4. Products under this series are compatible with SONET/SDH standards for OC-48/STM-16 (2.488Gb/s) LR-2/L-16.2 long reach applications, OC-3/STM-1 (156Mb/s) and OC-12/STM-4 (622Mb/s) SR/I-1 and I-4 short reach applications; Gigabit Ethernet LX (1.25Gb/s) applications per IEEE 802.3; and Fibre Channel 200-SM-LC-L (2.125Gb/s) and 100-SM-LC-L (1.062Gb/s) applications per FC-PI standards. The transceivers support data rates ranging from 2.67Gb/s down to 125Mb/s and are available in eight (8) wavelengths: 1471nm, 1491nm, 1511nm, 1531nm, 1551nm, 1571nm, 1591nm and 1611nm. The higher optical link power budget of 28dB is to accommodate the wavelength multiplexing and de-multiplexing insertion losses. All transceivers are Class I Laser products per U.S. FDA/CDRH and international IEC-60825 standards. The TRPA48L2M CWDM transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without removing the power supply from the host system. The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. The transmitter and receiver DATA interfaces are AC-coupled internally. LV-TTL Transmitter Disable control input and Loss of Signal (LOS) output interfaces are also provided. The transceivers operate from a single +3.3V power supply over an operating case temperature range of -5°C to +70°C (“B” option) or -5°C to +85°C (“E” option). The housing is made of metal for EMI immunity. Features Eight (8) Wavelength CWDM Transceivers Compatible with SFP MSA Compatible with SONET/SDH OC-48/STM-16 (2.488Gb/s) LR-2/L-16.2 Applications Compatible with Gigabit Ethernet LX Compatible with Fibre Channel 200-SM-LC-L and 100-SM-LC-L Digital Diagnostics through Serial Interface Internal Calibration for Digital Diagnostics APD Receiver Optical Link Power Budget of 28dB Minimum Eye Safe (Class I Laser Safety) Hot-pluggable TX Fault & Loss of Signal Outputs TX Disable Input Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature1 “B” Option “E” Option Supply Voltage Maximum Input Optical Power (30 seconds max.) Input Voltage 1 Symbol Minimum Maximum Units TST - 40 + 85 °C -5 + 70 -5 + 85 0 + 4.5 V Pin,max - + 3.0 dBm VIN 0 VCC V TOP VCC °C Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevB-NP.2008.09.09 TRPA48L2M CWDM Transmitter Performance Characteristics (Over Operating Case Temperature. VCC = 3.13 to 3.47V) All parameters guaranteed only at typical data rate Parameter Symbol Minimum Typical Maximum Units Operating Data Rate B 0.125 - 2.67 Mb/s Average Optical Output Power (coupled into single mode fiber), 50% duty cycle PO 0 - + 5.0 dBm Phi /Plo 8.2 - - dB Extinction Ratio 1471 1464.5 1471 1477.5 1491 1484.5 1491 1497.5 1511 1504.5 1511 1517.5 1531 Center Wavelength 1524.5 1531 1537.5 1544.5 1551 1557.5 1571 1564.5 1571 1577.5 1591 1584.5 1591 1597.5 λC 1551 1611 Spectral Width (-20dB) Side Mode Suppression Ratio nm 1604.5 1611 1617.5 Δλ20 - - 1.0 nm SMSR 30 - - dB Optical Rise/Fall Time (20% to 80%) t r , tf - - 0.16 ns Relative Intensity Noise RIN -- - - 117 dB/Hz JG - - 0.07 UIp-p - -- - 2.0 dB Jitter Generation OC-48 Dispersion Penalty 2 Optical Output Eye 2 Compliant with Telcordia GR-253-CORE and ITU-T Recommendation G.957 Specified at 1760ps/nm dispersion, which corresponds to the approximate worst-case dispersion for 80km G.652/G.654 fiber over the center wavelength range of 1464.5-1617.5nm. Receiver Performance Characteristics All parameters guaranteed only at typical data rate Parameter Operating Data Rate (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Symbol Minimum Typical Maximum Units B 0.125 - 2.67 Gb/s Receiver Sensitivity (10-10 BER)1 OC-3/12/48, 2.67Gb/s Pmin - 28.0 - - dBm Receiver Sensitivity (10-12 BER)2 2.125Gb/s, 1.25Gb/s, 1.062Gb/s, 0.125Gb/s Pmin - 28.0 - - dBm Pmax - 8.0 - - dBm Maximum Input Optical Power (10 -12 BER) Increasing Light Input Plos+ - - - 28.0 Decreasing Light Input Plos- - 42.0 - - Increasing Light Input t_loss_off - - 100 Decreasing Light Input t_loss_on 2.3 - 100 LOS Hysteresis - 0.53 - - dB Wavelength of Operation λ 1260 - 1620 nm Receiver Reflectance - - - - 27.0 dB LOS Thresholds LOS Timing Delay 1 2 3 dBm μs Measured with 223-1 PRBS. Measured with 27-1 PRBS. For OC-3, Minimum Hysteresis is 0.2dB. Oplink Communications, Inc. 2 RevB-NP.2008.09.09 TRPA48L2M CWDM Transmitter Performance Characteristics Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) (Over Operating Case Temperature. VCC = 3.13 to 3.47V) Symbol Minimum Typical Maximum Units VPP-DIF 0.35 - 1.75 V VIH VCC V 2.0 - 2 VIL 0 - 0.8 V Output HIGH Voltage (TX Fault) 3 VOH 2.0 - VCC + 0.3 V Output LOW Voltage (TX Fault) VOL 0 - 0.8 V Input LOW Voltage (TX Disable) 1 2 3 2 3 Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Receiver Electrical Interface Parameter Symbol Minimum Typical Maximum Units VPP-DIF 0.40 - 1.75 V Output HIGH Voltage (LOS) 2 VOH VCC - 1.3 - VCC + 0.3 V Output LOW Voltage (LOS)) 2 VOL 0 - 0.5 V Output Voltage Swing (RD+ & RD-) 1 2 1 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics Parameter (Over Operating Case Temperature. VCC = 3.13 to 3.47V)) Symbol Minimum Typical Maximum Units Supply Voltage VCC 3.13 3.3 3.47 V Supply Current ICC - 210 350 mA Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module definition protocol Electrical Pad Layout Host Board Connector Pad Layout 20 TX GND 1 TX GND 19 TD- (TX DATA IN-) 2 TX Fault 1 18 TD+ (TX DATA IN+) 3 TX Disable 2 17 TX GND 4 MOD_DEF(2) 3 16 VccTX 5 MOD_DEF(1) 4 15 VccRX 6 MOD_DEF(0) 14 RX GND 7 NO CONNECTION 6 13 RD+ (RX DATA OUT+) 8 LOS 7 12 RD- (RX DATA OUT-) 9 RX GND 8 11 RX GND 10 RX GND 9 Top of Board Oplink Communications, Inc. Toward Bezel 5 10 Bottom of Board (as viewed thru top of board) 3 20 19 18 17 16 15 14 Toward ASIC 13 12 11 RevB-NP.2008.09.09 TRPA48L2M CWDM Example of SFP host board schematic Vcc 3.3V 1μH coil or ferrite bead (<0.2Ω series resistance) Vcc 3.3V + 0.1 10 0.1 + 10 0.1 R R 16 15 R R 2 TX Fault 8 LOS 4 MOD_DEF(2) TRPA48L2M 5 CWDM MOD_DEF(1) MOD_DEF(0) TX Disable 3 TX DATA IN+ 18 13 RX DATA OUT+ to 50Ω load TX DATA IN- 19 12 RX DATA OUTto 50Ω load 100 6 (100Ω to ground internally) 1, 9, 10, 11, 14, 17, 20 R: 4.7 to 10kΩ Application Notes Electrical interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1μF and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10kΩ resistor on the host board Upon power up, MOD_DEF(1:2) appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected, and the negative edge clocks data from the SFP. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the startand end of serial protocol activation. The supported monitoring functions are internal temperature, supply voltage, bias current, transmitter power, average receiver signal, all alarms and warnings and software monitoring of TX Fault/LOS. The device is internally calibrated. TX_Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output that should be pulled up with a 4.7 - 10kΩ resistor on the host board. TX Fault is latched per SFP MSA. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFPMSA, and SFF-8472, Rev. 9.4 TX_Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Power supply and grounding: The power supply line should be well-filtered. All 0.1μF power supply bypass capacitors should be as close to the transceiver module as possible. Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Laser Safety Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements 4 RevB-NP.2008.09.09 TRPA48L2M CWDM 46335 Landing Pkwy Fremont, CA 94538 Tel: (510) 933-7200 Fax: (510) 933-7300 Email: [email protected] • www.oplink.com Mechanical Package Dimensions in inches [mm] Default tolerances: .xxx = ± .005”, .xx = ± .01” Ordering Information Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink’s Sales and Marketing for your requirements and ordering information (510) 933-7200 or [email protected]. Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Communications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. RevB-NP.2008.09.09 © 2006, Oplink Communications, Inc. 5