14 Pin DIP and SMD 5 Tap Low-Profile TTL Compatible Active Delay Lines Compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process. Delays are ±5% or ±2 nS† Tap Total 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 25 30 35 40 45 50 60 75 100 125 150 175 DIP Part Number SMD Part Number EP8200-HL EP8213-HL EP8214-HL EP8215-HL EP8216-HL EP8201-HL EP8211-HL EP8217-HL EP8202-HL EP8219-HL EP8203-HL EP8220-HL EPA073HL-25 EPA073HL-30 EPA073HL-35 EPA073HL-40 EPA073HL-45 EPA073HL-50 EPA073HL-60 EPA073HL-75 EPA073HL-100 EPA073HL-125 EPA073HL-150 EPA073HL-175 DC Electrical Characteristics Parameter Test Conditions VOH VOL VIK IIH High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current IIL IOS Low-Level Input Current Short Circuit Output Current ICCH High-Level Supply Current ICCL Low-Level Supply Current TRO Output Rise Time Fanout High-Level Output Fanout Low-Level Output SMD Part Number 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 84, 188, 282, 376 100, 200, 300, 400 EP8204-HL EP8221-HL EP8205-HL EP8206-HL EP8207-HL EP8208-HL EP8218-HL EP8222-HL EP8209-HL EP8223-HL EP8210-HL EPA073HL-200 EPA073HL-225 EPA073HL-250 EPA073HL-300 EPA073HL-350 EPA073HL-400 EPA073HL-420 EPA073HL-440 EPA073HL-450 EPA073HL-470 EPA073HL-500 200 225 250 300 350 400 420 440 450 470 500 Schematic Min Max Unit VCC = min. V IL = max. I OH = max 2.7 VCC = min. VIH = min. I OL= max VCC = min. II = IIK VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. -40 (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) Td > 500 nS VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V V V V µA mA mA mA 0.5 -1.2 50 1.0 -2 -100 14 12 VCC 4 10 6 8 OUTPUT INPUT 1 75 mA 75 mA 4 nS 5 nS 20 TTL LOAD 10 TTL LOAD 7 GROUND Input Pulse Test Conditions @ 25° C Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA DIP Part Number Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. †Whichever is greater. NH NL Delays are ±5% or ±2 nS† Tap Total Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature Min Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 40 +70 0 EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage Unit 3.2 110 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts *These two values are inter-dependent. SMD Package .400 Max. DIP Package .200 PCA EPA073HL-25 Date Code .280 Max. Suggested Solder Pad Layout .055 White Dot Pin#1 .200 PCA EP8201-HL Date Code .410 .300 .300 .200 .300 .280 Max. .03 .100 .780 Max. .780 Max. .01 Typ. .165 Max. .02 DSD82XXHL & DSA073HL .100 .020 Min. .200 Max. .050 .300 .020 Typ. .125 ± .01 Rev. A 2/5/96 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .365 Max. .010 Typ. QAF-CSO1 Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791