PI5A3157 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 SOTINYTM Low Voltage SPDT Analog Switch 2:1 Mux/Demux Bus Switch Features Description • • • • • • • • • • • • • The PI5A3157 is a high-bandwidth, fast single-pole double-throw (SPDT) CMOS switch. It can be used as an analog switch or as a low-delay bus switch. Specified over a wide operating power supply voltage range, 1.65V to 5.5V, the PI5A3157 has a maximum ON resistance of 12-ohms at 1.65V, 9-ohms at 2.3V & 6-ohms at 4.5V. CMOS Technology for Bus and Analog Applications Low ON Resistance: 8-ohms at 3.0V Wide VCC Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. Fast Transition Speed: 5.2ns max. at 5V High Off Isolation: 57dB at 10MHz 54dB (10MHz) Crosstalk Rejection Reduces Signal Distortion Break-Before-Make Switching High Bandwidth: 250 MHz Extended Industrial Temperature Range: –40°C to 85°C Improved Direct Replacement for NC7SB3157 Packaging (Pb-free & Green available): - 6-pin TDFN (ZA) - 6-pin SC70 (C) Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. The control input, S, tolerates input drive signals up to 5.5V, independent of supply voltage. PI5A3157 is an improved direct replacement for the NC7SB3157. Applications • • • • • Cell Phones PDAs Portable Instrumentation Battery Powered Communications Computer Peripherals Connection Diagram Pin Description Pin Numbe r Name 1 B1 2 GND 3 B0 Data Port (Normally Closed) 4 A Common Output/Data Port 5 VCC 6 S De s cription B1 1 6 S GND 2 5 VCC B0 3 4 A Data Port Ground Positive Power Supply Logic Control Logic Function Table Logic Input (S) Function 0 B0 Connected to A 1 B1 Connected to A 1 PS8552D 02/24/05 PI5A3157 SOTINYTM Low Voltage SPDT Analog Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Absolute Maximum Ratings(1) Recommended Operating Conditions(3) Supply Voltage VCC ................................................ –0.5V to +7V DC Switch Voltage (VS)(2) ............................. –0.5V to VCC +0.5V DC Input Voltage (VIN)(2) .................................... –0.5V to +7.0V DC Output Current (VOUT) ............................................... 128mA DC VCC or Ground Current (ICC/IGND) ............................ ±100mA Storage Temperature Range (TSTG) ................ –65°C to +150°C Junction Temperature under Bias (TJ) ............................... 150°C Junction Lead Temperature (TL) (Soldering, 10 seconds) ................................................ 260°C Power Dissipation (PD) @ +85°C ..................................... 180mW Supply Voltage Operating (VCC) . . . . . . . . . . . . . . 1.65V to 5.5V Control Input Voltage (VIN) . . . . . . . . . . . . . . . . . . . . 0V to VCC Switch Input Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . 0V to VCC Output Voltage (VOUT) . . . . . . . . . . . . . . . . . . . . . . . . 0V to VCC Operating Temperature (TA) . . . . . . . . . . . . . . . –40°C to +85°C Input Rise and Fall Time (tr,tf) Control Input VCC = 2.3V - 3.6V . . . . . . . . . . 0ns/V to 10ns/V Control Input VCC = 4.5V - 5.5V . . . . . . . . . . . 0ns/V to 5ns/V Thermal Resistance (θJA) . . . . . . . . . . . . . . . . . . . . . . 350°C/W Notes 1. Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the inut and output diode current ratings are observed. 3. Control input must be held HIGH or LOW; it must not float. DC Electrical Characteristics (Over the Operating temperature range, TA = –40°C to 85°C) Parame te r De s cription VIAR Te s t Conditions Analog Input Signal Range Supply Voltage Te mp (ºC) M in. VCC TA = 25°C & –40°C to 85°C 0 IO = 30mA, VIN = 0V RON IO = –30mA, VIN = 2.4V 4.5V TA = 25°C IO = –30mA, VIN = 4.5V Typ IO = –30mA, VIN = 2.4V RON RON RON RON RON IO = 24mA, VIN = 0V IO = –24mA, VIN = 3.0V ON IO = 24mA, VIN = 0V Resistance(4) IO = –24mA, VIN = 3.0V IO = 8mA, VIN = 0V IO = –8mA, VIN = 2.3V IO = 30mA, VIN = 0V IO = –30mA, VIN = 2.4V IO = 4mA, VIN = 0V IO = –4mA, VIN = 1.65V IO = 4mA, VIN = 0V IO = –4mA, VIN = 1.65V VCC V 6 5 8 8 13 6 4.5V TA = –40°C to 85°C 8 IO = –30mA, VIN = 4.5V RON Units 4 IO = 30mA, VIN = 0V RON M ax. 13 3.0V TA = 25°C 3.0V TA = –40°C to 85°C 2.3V TA = 25°C 2.3V TA = –40°C to 85°C 1. 6 5 V TA = 25°C 1.65V TA = –40°C to 85°C 5 8 12 19 8 19 6 9 16 24 9 24 8 12 27 39 12 39 PS8552D 2 Ω 02/24/05 PI5A3157 SOTINY Low Voltage SPDT Analog Switch 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 TM DC Electrical Characteristics (Over the Operating temperature range, TA = –40°C to 85°C) (continued) Parame te r ∆RON RONF De s cription ON Resistance Match Between Channels(4,5,6) Te s t Conditions SupplyVoltage VIL Typ 4.5V IA = –24mA, VBn = 2.1V 3.0V IA = –8mA, VBn = 1.6V 2.3V 0.3 IA = –4mA, VBn = 1.15V 1.65V 0.3 IA = –30mA, 0 ≤VBn ≤VCC 5.0V 6 ON IA = –24mA, Resistance 0 ≤VBn ≤VCC Flatness (4,5,7) IA = –8mA, 0 ≤VBn ≤VCC 3.3V Logic High Level Input Low Voltage Logic Low Level 0 ≤VIN ≤5.5V 90 TA = 25°C & –40°C to 85°C Ω 12 TA = 25°C 1.8V 0.75VCC V 0.7VCC VCC = 1.65V to 1.95V 0.25VCC VCC = 2.3V to 5.5V 0.25VCC VCC = 0V to 5.5V IOFF OFF State Leakage Current 0 ≤VIN ≤5.5V VCC = 1.65V to 5.5V ICC Quiescent Supply Current All channels ON or OFF, VIN = VCC or GND, IOUT = 0 VCC = 5.5V Units Ω 0.2 TA = 25°C 22 VCC = 2.3V to 5.5V M ax. 0.15 2.5V VCC = 1.65V to 1.95V Input High Voltage Input Leakage Current M in. IA = –30mA, VBn = 3.15V IA = –4mA, 0 ≤VBn ≤VCC VIH Te mp (ºC) TA = 25°C ±0.1 TA = –40°C to 85°C ±1.0 TA = 25°C ±0.1 TA = –40°C to 85°C ±10 TA = 25°C 1 TA = –40°C to 85°C 10 V µA Notes: 4. Measured by voltage drop between A and B pins at the indicated current through the device. ON resistance is determined by the lower of the voltages on two ports (A or B). 5. Parameter is characterized but not tested in production. 6. DRON = RON max – RON min. measured at identical VCC, temperature and voltage levels. 7. Flatness is defined as difference between maximum and minimum value of ON resistance over the specified range of conditions. 8. Guaranteed by design. Capacitance(12) Parame te r CIN De s cription Te s t Conditions Supply Voltage Te mp (ºC) For B Port, Switch OFF CIOA- ON For A Port, Switch ON Typ M ax. Units 2.3 Control Input CIO- B M in. f = 1 MHz(12) VCC = 5.0V TA = 25°C 6.5 pF 18.5 PS8552D 3 02/24/05 PI5A3157 SOTINYTM Low Voltage SPDT Analog Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Switch and AC Characteristics Parame te r De s cription tPLH tPHL tPZL tPZH tPZL tPZH tPLZ tPHZ tPLZ tPHZ Supply Voltage Te s t Conditions Propagation Delay: A to Bn See test circuit diagrams 1 and 2. VI Open (10) Output Enable Turn ON Time: A to Bn See test circuit diagrams 1 & 2. VI = 2VCC for TPZL, VI = 0V for tPZH OUTPUT ENABLE TURN ON TIME: A TO BN See test circuit diagrams 1 and 2. VI = 2VCC for TPZL, VI = 0V for tPZH Output See test circuit Disable Turn diagrams 1 and 2. VI = 2VCC for TPZL, OFF Time: VI = 0V for tPZH A to Bn Output See test circuit Disable Turn diagrams 1 and 2. VI = 2VCC for TPZL, OFF Time: VI = 0V for tPZH A to Bn Te mp (ºC) VCC = 3.0V to 3.6V TA = 25°C & –40 to 85°C TA = 25°C VCC = 4.5V to 5.5V Break Before See test circuit Make Time diagram 9.(9) OIRR XTALK f3dB 23 3.5 13 2.5 6.9 1. 7 5.2 24 VCC = 3.0V to 3.6V 14 TA = 25°C & –40 to 85°C 7.6 VCC = 4.5V to 5.5V 5.7 VCC = 1.65V to 1.95V VCC = 2.3V to 2.7V VCC = 3.0V to 3.6V TA = 25°C VCC = 4.5V to 5.5V 3 12.5 2 7 1. 5 5 0.8 3.5 VCC = 3.3V VCC = 3.0V to 3.6V 7.5 TA = –40 to 85°C 5.3 VCC = 4.5V to 5.5V VCC = 3.3V VCC = 3.0V to 3.6V VCC = 5.0V 3.8 0.5 TA = 25°C & –40 to 85°C 0.5 0.5 0.5 7 Charge Injection CL = 0.1nF, VGEN = 0V, RGEN = 0Ω . See test circuit 4. Off Isolation RL = 50Ω , VGEN = 0V, RGEN = 0Ω. See test circuit 5. (11) VCC = 1.65V to 5.5V Crosstalk Isolation See test circuit 6. VCC = 1.65V to 5.5V TA = 25°C –54 –3dB Bandwidth See test circuit 9 VCC = 1.65V to 5.5V TA = 25°C 250 VCC = 3.3V ns 13 VCC = 2.5V VCC = 4.5V to 5.5V Q 7 VCC = 2.5V VCC = 3.3V Units 0.3 VCC = 1.65V to 1.95V VCC = 3.0V to 3.6V M ax. 0.8 VCC = 4.5V to 5.5V VCC = 2.3V to 2.7V Typ 1.2 VCC = 2.3V to 2.7V VCC = 2.5V tBM M in. TA = 25°C TA = 25°C pC 3 –57 dB MHz Notes: 9. Guaranteed by design. 10. Guaranteed by design but not production tested. The device contributes no other propagation delay other than the RC delay of the switch ON resistance and the 50pF load capacitance, whne driven by an ideal voltage source with zero output impedance. 11. Off Isolation = 20 Log10 [ VA / VBn ] and is measured in dB. 12. TA = 25°C, f = 1MHz. Capacitance is characterized but not tested in production. PS8552D 4 02/24/05 PI5A3157 SOTINY Low Voltage SPDT Analog Switch 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 TM Test Circuits and Timing Diagrams From Output Under Test CL 10pF Notes: 100Ω Input driven by 50W source terminated in 50Ω. CL includes load and stray capacitance. Input PRR = 1.0 MHz; tw = 500ns. Figure 1. AC Test Circuit tr = 2.5ns tr = 2.5ns tr = 2.5ns tr = 2.5ns 90% SWITCH INPUT VCC 90% 50% 10% GND 10% 10% tW tPLH 50% VCC 90% 10% 50% 50% 90% CONTROL INPUT tPLZ tPZL GND VTRI tPHL OUTPUT 50% VOH VOL+0.3V OUTPUT VOL 50% tPZH 50% tPHZ VOH VOL OUTPUT VOH –0.3V 50% VTRI Figure 2. AC Waveforms VIN B0 A VOUT B1 RL CL Logic Input V OUT A 0.9 x V OUT Logic Input tD Figure 3. Break Before Make Interval Timing PS8552D 5 02/24/05 PI5A3157 SOTINYTM Low Voltage SPDT Analog Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 RGEN A BN VOUT RL 1MΩ VGE Logic Input OFF ON OFF CL 100pF ∆V OUT S Logic Input Q = (∆V OUT )(CL ) Figure 4. Charge Injection Test VCC VCC 10nF 10nF VCC A Logic Input 0V or BIH 50Ω S VCC Signal Generator 0dBm B1 50Ω BN Analyzer Analyzer GND 50Ω GND S 50Ω Figure 6. Crosstalk Figure 5. Off Isolation VCC VCC 10nF 10nF A Capacitance Meter VCC Capacitance Meter f = 1 MHz A B0 S A VCC f = 1 MHz Logic Input 0V or BIH S Logic Input 0V or BIH BN BN GND GND Figure 8. Channel On Capacitance Figure 7. Channel Off Capacitance PS8552D 6 02/24/05 PI5A3157 SOTINY Low Voltage SPDT Analog Switch 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 TM VCC 10nF VCC Signal Generator 0dBm A BN 50Ω S Logic Input 0V or VCC GND Figure 9. Bandwidth Packaging Mechanical: 6-Pin SC70 (C) 6 5 4 1 2 3 PS8552D 7 02/24/05 PI5A3157 SOTINYTM Low Voltage SPDT Analog Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 2:1 Mux/Demux Bus Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 6-Pin TDFN (ZA) 0.1 x 45˚ CHAMFER 0.80 MAX Pin 1 1.00 ± 0.10 0.23 ± 0.05 (6x) 1.00 0.80 MAX 1.50 ± 0.10 0.50 Typ. 0.13 0.0 - 0.05 0.30 ± 0.10 (6x) Bottom View Side Views Top View Ordering Information Ordering Code Package Code Package Description Top Marking PI5A3157CX C 6-pin SC70 ZM PI5A3157CEX C Pb-free & Green 6-pin SC70 ZM PI5A3157ZAEX ZA Pb-free & Green 6-contact TDFN ZM Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. X = Tape and reel Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com PS8552D 8 02/24/05