PERICOM PI5C6801C

PI5C6801C
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
10-Bit Bus Switch with Precharged Outputs
for Live Insertion and –2V Undershoot Protection
Product Description
Product Features
Pericom’s Semiconductor’s PI5C series of logic circuits are produced
using the Company’s advanced submicron CMOS technology,
achieving industry leading performance.
The PI5C6801C is a 10-bit bus switch with low on-state resistance.
The bus switch creates no additional propagation delay. The device
also precharges the B port to a user-selectable bias voltage (BIASV)
to minimize live-insertion noise.
The switch is turned on by a single enable (ON) input. When ON is
LOW, the switch is on and port A is connnected to port B. When ON
is HIGH, the switch between port A and port B is open and the B port
is precharged to BIASV through the equivalent of a 10-kΩ resistor.
• RON is 5 Ohm typical
• Undershoot protection on A-port only
• Industrial Operation Temperature: –40ºC to +85ºC
• Near Zero propagation delay
• VCC Operating Range: +4.0V to +5.5V
• Outputs are pre-charged by bias voltage to minimize
signal distortion during live insertion
• Packages options:
-24-pin 150 mil-wide plastic QSOP (Q)
-24-pin 173 mil-wide plastic TSSOP (L)
Product Pin Configuration
Logic Diagram
13
23
A1
14
A10
ON
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
GND
B1
B10
ON
Truth Table(1)
Function
Connect
Precharge
ON
L
H
B1 - B10
A1 - A10
BIASV
Notes:
1. H = High Voltage Level
L = Low Voltage Level
1
1
2
3
4
5
6
7
8
9
10
11
12
24-Pin
L, Q
24
23
22
21
20
19
18
17
16
15
14
13
VCC
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
BIASV
PS8374B
05/02/00
PI5C6801C
10-Bit BusSwitch with PrechargedOutputs
for Live Insertion and -2V Undershoot Protection
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
Absolute Maximum Ratings Over Free-Air Temperature Range*
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect reliability.
Storage Temperature ............................................................ –65°C to +150°C
Supply Voltage Range ................................................................ –0.5V to +7V
DC Input Voltage(1) .................................................................................... –0.5V to +7V
Input Clamp Current, IIK (V1<0) .......................................................... –50mA
DC Output Current .............................................................................. 120mA
Power Dissipation(2) .................................................................................................. 0.5W
Notes:
1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils.
Recommended Operating Conditions
Parame te r
De s cription
M in.
M ax.
VCC
Supply voltage
4
5.5
BIASV
Supply voltage
1.3
VCC
VIH
High- Level input voltage
VIL
Low- level input voltage
TA
Operating free- air temperature
Units
V
2
0.8
–40
85
°C
Electrical Characteristics (Over Recommended Operating Free-air Temperature Range)
Parame te r
Te s t Conditions
M in.
Typ=
M ax.
Units
–1.8
V
±5
µA
VIK
VCC = 4.5V
II = –18mA
II
VCC = 5.5V
VI = 5.5V or GND
IO
VCC = 4.5V
BIASV = 2.4V
VO= 0V
ICC
VCC = 5.5V
IO = 0A
VI = VCC or GND
100
µA
O ne input at 3.4V
O ther at VCC or GND
2.5
mA
∆ICCE
Control pins
VCC = 5.5V
CI
Control pins
VI = 3V or 0V
CO(O FF)
–0.20
mA
3.5
pF
VO = 3V or 0V
Switch O ff
VCC = 4V
VI = 2.4V
II = 15mA
9
28
VI = 0V
II = 64mA
5.5
8
VI = 0V
II = 30mA
5
8
VI = 2.4V
II = 15mA
9
16
RON*
VCC = 4.5V
4.5
Ω
Notes:
* Measured by the voltage drop between the A and B terminals at the indicated current through the switch.
On-state resistance is determined by the lower of the voltages of the two (A or B) terminals.
E This is the increase in supply current for each input that is at the specified TTL voltage level rather the VCC or GND.
= All typical values are at VCC = 5V, TA = 25°C.
2
PS8374B
05/02/00
PI5C6801C
10-Bit BusSwitch with PrechargedOutputs
for Live Insertion and -2V Undershoot Protection
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
Switching Characteristics (Over Recommended Operating Free-air Temperature Range, CL = 50pF)
Te s t Conditions (1)
Parame te r
From (Input)
To (Output)
A or B
B or A
ON
A or B
ON
A or B
tpd
tPZH
BIASV = GND
tPZL
BIASV = 3V
tPHZ
BIASV = GND
tPLZ
BIASV = 3V
VCC = 5V ± 0.5V
M in.
M ax.
VCC = 4V
M in.
M ax.
0.25
Units
0.25
20
30
22
36
20
30
22
36
20
30
22
36
20
30
22
36
ns
Notes:
1. This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical
on-state resistance of the switch and a load capacitance of 50pF, when driven by an ideal voltage source (zero output impedance).
Parameter Measurements
7V
S1
From Output
Under Test
CL = 50pF
(See note 1)
Output
Control
(Low Level
Enabling)
LOAD CIRCUIT
3V
Output
Waveform 1
S1 at 6V
(see Note 2)
1.5V
1.5V
Input
0V
tPLH
tPHL
VOH
Output
1.5V
Te s t
S1
tpd
O pen
tPLZ/tPZL
7V
tPHZ/tPZH
O pen
Open
GND
Output
Waveform 2
S1 at Open
(see Note 2)
1.5V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
3V
1.5V
1.5V
0V
tPZL
tPLZ
3.5V
1.5V
VOL +0.3V
tPZH
VOL
tPHZ
VOH
1.5V
VOH -0.3V
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
Notes:
1. CL includes probe and jig capacitance.
2. Waveform 1 is for an output with internal conditions such that the output is LOW except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is HIGH except when disabled by the output control.
3. All input pulses are supplied by generators having the following characteristics: PRR<10MHz, ZO = 50Ω, tr ≤ 2.5ns, tf ≤ 2.5ns.
4. The outputs are measured one at a time with one transition per measurement.
5. tPLZ and tPHZ are the same as tdis.
6. tPZL and tPZH are the same as ten.
7. tPLH and tPHL are the same as tpd.
3
PS8374B
05/02/00
PI5C6801C
10-Bit BusSwitch with PrechargedOutputs
for Live Insertion and -2V Undershoot Protection
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
24-pin QSOP (Q)
24
.150
.157
3.81
3.99
.015 x 45˚
0.38
1
.337
.344
.007
.010
8.56
8.74
.016
.050
.033
0.84
.053
.069
1.35
1.75
.008 0.203
.012 0.305
0.406
1.27
.228
.244
5.79
6.20
SEATING
PLANE
.025
typical
0.635
0.178
0.254
.004 0.101
.010 0.254
X.XX DENOTES DIMENSIONS
X.XX IN MILLIMETERS
4
PS8374B
05/02/00
PI5C6801C
10-Bit BusSwitch with PrechargedOutputs
for Live Insertion and -2V Undershoot Protection
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
24-pin TSSOP (L)
24
.169
.177
1
4.3
4.5
.303
.311
7.7
7.9
.004
.008
.047
1.20
Max
.0256
BSC
0.65
.007
.012
0.19
0.30
.002
.006
0.45
0.75
SEATING
PLANE
0.09
0.20
.018
.030
.252
BSC
6.4
0.05
0.15
X.XX DENOTES CONTROLLING
X.XX DIMENSIONS IN MILLIMETERS
Ordering Information
Part
Pin
Package
Width
PI5C6801CQ
24
QSOP (Q )
150- mil
PI5C6801CL
24
TSSOP (L)
173- mil
Applications Information
Logic Inputs
The logic control inputs can be driven up to +5.5V regardless of
the supply voltage. For example, given a +5.0V supply, IN may
be driven low to 0V and high to 5.5V. Driving IN Rail-to-Rail®
minimizes power consumption.
Power-Supply Sequencing
Proper power-supply sequencing is recommended for all CMOS
devices. Always apply VCC before applying VBIAS and signals to
the input/output or control pins.
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd
Pericom Semiconductor Corporation
2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com
5
PS8374B
05/02/00