(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com FES SERIES - 300 WATT DESCRIPTION FEATURES FES single output DC/DC converters provide up to 300 Watts of output power and up to 60 Amperes of output current in a full brick package. The FES converters feature open-frame packaging, along with planar magnetics and a high efficiency topology, to provide maximum useable power density. The FES converters use 100% surface-mount construction and are fully compatible with production board washing processes. • • • • 60A “Full Brick” Very High Efficiency Open-Frame Packaging 100°C Baseplate Operation • Planar Magnetics • Excellent Transient Response • 1500V Isolation • Synchronous Rectification TECHNICAL SPECIFICATIONS Input Voltage Range 48 VDC Nominal Undervoltage Lockout - Turn on / Turn off 36 - 75 VDC 34 / 32 VDC Output ±1% 0.2% V out 0.2% V out 0.5 VDC 10 % Iout Rated 25% Iout 4% Vout 500 µs ±10% 110 - 140% 120 - 140% Vout Nom. Self Recovering Shutdown/Hiccup Efficiency vs. Load (48V Input) 95 90 85 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Current Limit Threshold Range, % of Iout Rated OVP Trip Range OVP Type Short Circuit/Over Current Protection 80 FES200ZE-A 75 EFF. (36V) EFF. (48V) 70 EFF. (75V) 65 General Turn-On Time Remote Shutdown Remote Shutdown Reference Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (Approx.) 60 10 ms Positive Logic Vin Negative 200 or 300 kHz 1500 VDC 1050 VDC 500 VDC 0.03%/°C -40 To +100°C -40 To +125°C 105 To 125°C 5 g, 10 - 55 Hz Consult Factory UL, CUL, TUV 4.4 oz C-56 10 20 30 40 50 60 70 80 90 100 LOAD % Notes † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. FES SERIES - 300 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** Model 48 48 48 48 48 48 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 36 - 75 3.5 4.5 6.5 5.0 7.0 10.5 2.5 3.3 5.0 2.5 3.3 5.0 40 40 40 60 60 60 100 100 100 100 100 100 85% 87% 80% 79% 81% 84% FES100ZD-A FES132ZE-A FES200ZG-A FES150ZD-A FES200ZE-A FES300ZG-A * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 4.60" (116.8mm) MOUNTING INSERTS 0.18" M3X.5 THROUGH 4PL (4.6mm) 1.700"(43.2mm) 1 1.000"(25.4mm) 2 5 BOTTOM VIEW 0.400"(10.2mm) 6 1.150"(29.2mm) 7 0.900"(22.9mm) 8 0.700"(17.8mm) 9 0.500"(12.7mm) DIA 0.080" (2.0mm) 6PL 2.40" FES 1.400"(35.6mm) (61.0mm) 3 10 0 0.250"(6.4mm) DIA 0.040" 11 4 (1.0mm) 5PL -.300"(-7.6mm) -.50"(-12.7mm) -0.20" 0.025" REF. 4.200" 0 (0.6mm) (106.7mm) (-5.1mm) 0.50" (12.7mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 5.4 3.8 2.5 1.7 1.6 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 2 3 4 5 6 7 8 9 10 11 -Vin Case Enable +Vin -Vout -Vout -Sense Trim +Sense +Vout +Vout C-57 Tolerances Inches: .XX ± 0.020 .XXX ± .010 Pin: ± 0.002 (Millimeters) .X ± 0.5 .XX ± 0.25 ± 0.05 ( Dimensions as listed unless otherwise specified.) OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. C105