(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com XWD SERIES - DUAL OUTPUT, 180 WATT DESCRIPTION FEATURES XWD dual output, DC to DC converters are high powered converters that cover a wide range of applications. Available input voltages include 12V, 24V, 40V, and 48V. Output voltages are available from 5V to 15V. The XWD features remote sense leads for accurate point of load regulation, and has short circuit and overcurrent protection. For single and triple output high power solutions, see the XWS and XWT series of converters. • High Power Package • Wide Input Range • Trim and Enable • Remote Sense Pins • 500V Isolation • Short Circuit Protection Efficiency vs. Load (24V Input) 90 EFFICIENCY % 85 80 XWD2405 (18v) 75 (24v) (36v) 70 TECHNICAL SPECIFICATIONS Input Voltage Range 12 VDC Nominal 24 VDC Nominal 48 VDC Nominal 40 VDC Nominal (Wide Input) Input Ripple Current Reverse Input Current 65 10 10 18 36 20 20% 100% 20 VDC 36 VDC 72 VDC 60 VDC Iin Max. Iin Max. 20 30 40 50 60 70 80 90 100 90 100 LOAD % Efficiency vs. Load (48V Input) 90 Output Pk Deviation Settling Time Voltage Trim Range Current Limit Threshold Range, % of Iout Rated ±1% ±1% Vout ±1% Vout 10 % 25% Iout 4% Vout 500 µs ±10% 110 - 130% 85 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Dynamic Regulation, Loadstep XWD4812 80 XWD4815 75 70 10 General Turn-On Time Remote Shutdown Switching Frequency Isolation Input - Output Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (Approx.) 20 30 40 50 60 70 80 LOAD % 10 ms Positive Logic 200 kHz 500 VDC ±0.02%/°C -25 To +85°C†† -40 To +125°C 105 - 115°C 95% 5 g, 10 - 55 Hz Consult Factory Consult Factory 15.4 oz 1 Notes † MTBF predictions may vary slightly from model to model. †† Industrial temp range of -40 to +85°C available. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. XWD SERIES - DUAL OUTPUT, 180 WATT MODELS - (See the last page of Section C for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** Model 12 12 12 24 24 24 48 48 48 40 40 40 10 - 20 10 - 20 10 - 20 18 - 36 18 - 36 18 - 36 36 - 72 36 - 72 36 - 72 20 - 60 20 - 60 20 - 60 14.0 16.9 16.7 11.3 13.3 13.3 5.5 6.5 6.5 10.3 12.2 12.2 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ± 10 ± 5.2 ± 4.15 ± 15 ± 7.5 ±6 ± 15 ± 7.5 ±6 ± 15 ± 7.5 ±6 50 120 150 50 120 150 50 120 150 50 120 150 79% 81% 82% 82% 83% 83% 84% 85% 85% 80% 81% 81% XWD1205 XWD1212 XWD1215 XWD2405 XWD2412 XWD2415 XWD4805 XWD4812 XWD4815 XWD6005 XWD6012 XWD6015 Thermal Impedance * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Natural convection 100 LFM 200 LFM 300 LFM 400 LFM MECHANICAL DRAWING 5.50" (139.7mm) #4-40 THREADED INSERTS 4PLS. 2.625"(66.7mm) 3.50" 1 8 2.250"(57.2mm) 2 9 1.875"(47.6mm) 3 10 1.500"(38.1mm) 11 1.125"(28.6mm) 5 12 0.750"(19.1mm) 6 13 0.375"(9.5mm) 7 14 0 4 (88.9mm) BOTTOM VIEW -0.375"(-9.5mm) -0.625"(-15.9mm) -0.60" 4.300" 0 2.5 2.1 1.7 1.3 1.1 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 No Pin -Vin -Vin +Vin +Vin Enable Case -V1 Sense -V1out +V1out +V1 Sense1 - V2out Trim + V2out (109.2mm) (-15.2mm) Tolerances Inches: .XX ± 0.040 .XXX ± 0.010 DIA 0.040" 13PL. (1.0mm) Pin: ± 0.002 (Millimeters) .X ± 1.0 .XX ± 0.25 ± 0.05 0.92" (23.4mm) (Dimensions as listed unless otherwise specified.) 2 OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3