(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com XWS SERIES - 150 WATT DESCRIPTION FEATURES XWS DC/DC converters are high-powered converters • High Power Package which cover a wide range of industrial and general • Wide Input Range applications. Available input voltages include 12V, 24V, • Trim and Enable Pins 40V, and 48V; output voltages are available from 5V to 24V. The XWS features remote sense leads for accurate point of load regulation, and has short circuit and overcurrent protection. For dual and triple output high Efficiency power solutions, see the XWD and XWT series of converters, respectively. 95 • Remote Sense Pins • 500V Isolation • Short Circuit Protection vs. Load (24V Input) EFFICIENCY % 90 TECHNICAL SPECIFICATIONS 85 XWS2415 80 Input Voltage Range 12 VDC Nominal 24 VDC Nominal 40 VDC Nominal (Wide Input) 48 VDC Nominal Input Ripple Current Reverse Input Current 10 18 20 36 20% 100% 75 20 VDC 36 VDC 60 VDC 72 VDC I in Max. Iin Max. 10 30 40 50 60 70 80 90 100 90 100 LOAD % Efficiency vs. Load (48V Input) Output 95 ±1% ±0.2% Vout ±1% Vout 10 % lout rated 25% Iout 4% Vo 500 µs ±10% 110 - 130% Continuous All Models 90 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Current Limit Threshold Range, % of Iout Rated Short Circuit Protection OVP 20 85 80 XWS4805 75 XWS4815 70 65 10 General 20 30 40 50 60 70 80 LOAD % Turn-On Time 10 ms Remote Shutdown TTL And CMOS Compatible, Positive Logic Switching Frequency 200 kHz Isolation Input - Output 500 VDC Temperature Coefficient ±0.02%/°C Case Temperature Operating Range -25 To +85°C†† Storage Range -40 To +125°C Thermal Shutdown Range 105 To 115°C Humidity Max., Non-Condensing 95% Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz MTBF† (Bellcore TR-NWT-000332) Consult Factory Safety Consult Factory Weight (Approx.) 15.4 oz C48 Notes MTBF predictions may vary slightly from model to model. †† Industrial temp range available † Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. XWS SERIES - 150 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** Model 12 12 12 12 24 24 24 24 48 48 48 48 40 40 40 40 10 - 20 10 - 20 10 - 20 10 - 20 18 - 36 18 - 36 18 - 36 18 - 36 36 - 72 36 - 72 36 - 72 36 - 72 20 - 60 20 - 60 20 - 60 20 - 60 13.9 16.9 16.7 15.7 10.9 12.9 12.8 13.6 5.5 6.5 6.5 6.8 10.3 12.4 12.2 12.9 5 12 15 24 5 12 15 24 5 12 15 24 5 12 15 24 20 10.4 8.3 5 30 15 12 8 30 15 12 8 30 15 12 8 50 120 150 240 50 120 150 240 50 120 150 240 50 120 150 240 79% 81% 82% 84% 83% 85% 86% 86% 82% 85% 85% 86% 80% 80% 81% 82% XWS1205 XWS1212 XWS1215 XWS1224 XWS2405 XWS2412 XWS2415 XWS2424 XWS4805 XWS4812 XWS4815 XWS4824 XWS6005 XWS6012 XWS6015 XWS6024 * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM MECHANICAL DRAWING 5.50" (139.7mm) #4-40 THREADED INSERTS 4PLS. 2.625"(66.7mm) 3.50" 1 8 2.250"(57.2mm) 2 9 1.875"(47.6mm) 3 10 1.500"(38.1mm) 11 1.125"(28.6mm) 5 12 0.750"(19.1mm) 6 13 0.375"(9.5mm) 7 14 0 4 (88.9mm) BOTTOM VIEW -0.375"(-9.5mm) -0.625"(-15.9mm) -0.60" 4.300" 0 (109.2mm) (-15.2mm) 2.5 2.1 1.7 1.3 1.1 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DIA 0.040" 13PL. No Pin -Vin -Vin +Vin +Vin Enable Case -Vout -Vout +Vout +Vout - Sense Trim + Sense Tolerances (1.0mm) Inches: .XX ± 0.040 .XXX ± .010 (Millimeters) .X ± 1.0 .XX ± 0.25 Pin: ± 0.002 ± 0.05 0.92" (23.4mm) C49 (888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com XWS SERIES - 150 WATT TERMINAL STRIP OPTION MECHANICAL DRAWING DIA 0.041" 13PLS. (1.04mm) #4-40 THREADED INSERTS 4PLS. 1 8 2 9 3 10 4 11 5 12 6 13 7 14 0.52" (13.2mm) 0.375" EA. (9.53mm) DIA 0.18" (4.6mm) 0.25" (6.4mm) 3.50" (88.90mm) 3.000" (76.20mm) 0.92" (23.4mm) 4.300" (109.22mm) 5.50" (139.7mm) PIN VIEW UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES: .X }.030 .XX }.040 .XXX }.010 FRACTION }.030 C50 OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. C105