RDC ® R8820LV RISC DSP Controller R8820LV 16-Bit RISC Microcontroller User’s Manual RDC RISC DSP Controller RDC Semiconductor Co., Ltd http:\\www.rdc.com.tw Tel. 886-3-583-2666 Fax 886-3-583-2688 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 1 RDC ® R8820LV RISC DSP Controller Contents --------------------------------------------------------------------------------------- page 1. Features -------------------------------------------------------------------------------- 4 2. Block Diagram ------------------------------------------------------------------------ 4 3. Pin Configuration -------------------------------------------------------------------- 5 4. Pin Description------------------------------------------------------------------------ 8 5. Basic Application System Block & Read/Write timing Diagram ---------- 14 6. Oscillator Characteristics ---------------------------------------------------------- 17 7. Execution Unit ----------------------------------------------------------------------- 18 7.1 General Register ----------------------------------------------------------------- 18 7.2 Segment Register ---------------------------------------------------------------- 18 7.3 Instruction Pointer and Status Flags Register -------------------------------- 19 7.4 Address Generation ------------------------------------------------------------- 20 8. Peripheral Control Block Register ----------------------------------------------- 21 9. System Clock Block ----------------------------------------------------------------- 23 10. Reset ---------------------------------------------------------------------------------- 24 11. Bus Interface Unit------------------------------------------------------------------ 26 11.1 Memory and I/O Interface ---------------------------------------------------- 26 11.2 Data Bus------------------------------------------------------------------------- 26 11.3 Wait States ---------------------------------------------------------------------- 27 11.4 Bus Hold ------------------------------------------------------------------------ 28 11.5 Bus Width---------------------------------------------------------------------- 30 12. Chip Select Unit -------------------------------------------------------------------- 31 12.1 UCS ---------------------------------------------------------------------------- 31 12.2 LCS ---------------------------------------------------------------------------- 32 12.3 MCSx -------------------------------------------------------------------------- 33 12.4 PCSx --------------------------------------------------------------------------- 34 13. Interrupt Controller Unit--------------------------------------------------------- 37 13.1 Master Mode and Slave Mode ------------------------------------------------ 37 13.2 Interrupt Vector, Type and Priority ------------------------------------------ 38 13.3 Interrupt Request -------------------------------------------------------------- 39 13.4 Interrupt Acknowledge -------------------------------------------------------- 39 13.5 Programming Register--------------------------------------------------------- 40 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 2 RDC ® R8820LV RISC DSP Controller 14. DMA Unit --------------------------------------------------------------------------- 53 14.1 DMA Operation ---------------------------------------------------------------- 53 14.2 External Request --------------------------------------------------------------- 59 14.3 Serial Port / DMA Transfer ------------------------------------------------ 61 15. Timer Control Unit ---------------------------------------------------------------- 62 15.1 Timer/Counter Unit Output Mode ------------------------------------------ 66 16. Watchdog Timer ------------------------------------------------------------------- 68 17. Asynchronous Serial Port--------------------------------------------------------- 70 17.1 Serial Port Flow Control -------------------------------------------------- 70 17.1.1 DCE/DTE Protocol ------------------------------------------------ 70 17.1.2 CTS/RTR Protocol-------------------------------------------------- 71 17.2 DMA Transfer to/form a serial port function ------------------------- 71 17.3 The Asynchronous Modes description ---------------------------------- 72 18. PIO Unit ----------------------------------------------------------------------------- 77 18.1 PIO Multi-Function Pin list Table ------------------------------------------- 77 19. PSRAM Control Unit-------------------------------------------------------------- 80 20. Instruction Set Opcodes and Clock Cycle ------------------------------------- 81 20.1 R8820LV Execution Timings ------------------------------------------------ 85 21. DC Characteristics----------------------------------------------------------------- 86 22. AC Characteristics----------------------------------------------------------------- 88 23. Package Information -------------------------------------------------------------- 97 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 3 RDC ® R8820LV RISC DSP Controller 16-Bit Microcontroller with 16-bit external data bus 1. Features l Five-stages pipeline l Supports 32 PIO pins l RISC architecture l PSRAM (Pseudo static RAM) interface with l Static Design & Synthesizable design l Bus interface auto-refresh control l - Multiplexed address and Data bus which independent watchdog timer l is compatible with 80C186 microprocessor l The Interrupt controller with seven maskable - Supports nonmultiplexed address bus [A19 : A0] external interrupts and one nonmaskable - 1M byte memory address space external interrupt - 64K byte I/O space l Two independent DMA channels Software is compatible with the 80C186 l Programmable chip-select logic for Memory microprocessor l Three independent 16-bit timers and one or I/O bus cycle decoder Support two Asynchronous serial channel with l Programmable wait-state generator hardware handshaking signals. l Support serial port/ DMA transfers 2. Block Diagram INT2/INTA0 INT1/SELECT CLKOUTA INT3/INTA1/IRQ CLKOUTB INT6-INT4 X1 VCC GND X2 Clock and Power Management INT0 TMROUT0 TMROUT1 TMRIN0 TMRIN1 NMI Interrupt Control Unit Timer Control Unit DRQ0 DRQ1 DMA Unit RST LCS/ONCE0 MCS3/RFSH Chip Select Unit MCS2-MCS0 Instruction Queue (64bits) UCS/ONCE1 PSRAM Control Unit PCS3-PCS0 PCS5/A1 PCS6/A2 Refresh Control Unit ARDY SRDY S2~S0 DT/R DEN Instruction Decoder Micro ROM PIO Unit Control Signal Register File General, Segment, Eflag Register EA / LA Address RTS0/RTR0 Asynchronous Serial Port0 CTS0/ENRX0 TXD0 RXD0 RTS1/RTR1 Bus Interface Unit HOLD HLDA S6/CLKDIV2 UZI A19~A0 AD15~AD0 ALE ALU Execution Unit (Special, Logic, Adder, BSF) Asynchronous Serial Port1 CTS1/ENRX1 TXD1 RXD1 RD WHB WLB WR BHE/ADEN Rev:1.0 RDC Semiconductor Co. Subject to change without notice 4 RDC ® R8820LV RISC DSP Controller 3. Pin Configuration UZI/PIO26 S6/CLKDIV2/PIO29 AD15 AD7 AD14 VCC AD6 AD13 GND AD5 AD12 AD4 AD11 AD3 AD10 AD2 AD9 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 98 96 TXD1/PIO27 99 97 CTS0/ENRX0/PIO21 RXD1/PIO28 100 (PQFP) RXD0/PIO23 1 80 AD1 TXD0/PIO22 2 79 AD8 RTS0/RTR0/PIO20 3 78 AD0 BHE/ADEN 4 77 DRQ0/INT5/PIO12 WR 5 76 DRQ1/INT6/PIO13 RD 6 75 TMRIN0/PIO11 TMROUT0/PIO10 ALE 7 74 ARDY 8 73 TMROUT1/PIO1 S2 9 72 TMRIN1/PIO0 S1 10 71 RST S0 11 70 GND GND 12 69 MCS3/RFSH/PIO25 X1 13 68 MCS2/PIO24 R8820LV X2 14 VCC 15 CLKOUTA 16 CLKOUTB 17 64 GND GND 18 63 PCS2/CTS1/ENRX1/PIO18 A19/PIO9 19 62 PCS3/RTS1/RTR1/PIO19 A18/PIO8 20 61 VCC VCC 21 60 PCS5/A1/PIO3 A17/PIO7 22 59 PCS6/A2/PIO2 A16 23 58 LCS/ONCE0 A15 24 57 UCS/ONCE1 A14 25 56 INT0 A13 26 55 INT1/SELECT A12 27 54 INT2/INTA0/PIO31 A11 28 53 INT3/INTA1/IRQ A10 29 52 INT4/PIO30 A9 30 51 MCS1/PIO15 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A8 A7 A6 A5 A4 A3 A2 VCC A1 A0 GND WHB WLB HLDA HOLD SRDY/PIO6 NMI DT/R/PIO4 DEN/PIO5 MCS0/PIO14 Microcontroller 67 VCC 66 PCS0/PIO16 65 PCS1/PIO17 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 5 34 35 36 S0 GND X1 RDC Semiconductor Co. Subject to change without notice 6 44 45 46 47 48 49 50 A16 A15 A14 A13 A12 43 A18/PIO8 VCC 42 A17/PIO7 41 GND A19/PIO9 40 33 S1 CLKOUTB 32 S2 39 31 ARDY CLKOUTA 30 ALE 38 29 RD 37 28 WR X2 27 BHE/ADEN VCC 26 RTS0/RTR0/PIO20 MCS3/RFSH/PIO25 92 INT1/SELECT INT2/INTA0/PIO31 INT3/INTA1/IRQ 78 77 76 UCS/ONCE1 INT0 79 81 80 PCS6/A2/PIO2 LCS/ONCE0 82 VCC PCS5/A1/PIO3 85 83 PCS3/RTS1/RTR1/PIO19 86 84 GND PCS2/CTS1/ENRX1/PIO18 87 PCS1/PIO17 GND 93 PCS0/PIO16 RST 94 88 TMRIN1/PIO0 95 89 TMROUT1/PIO1 96 MCS2/PIO24 TMROUT0/PIO10 97 VCC TMRIN0/PIO11 98 90 DRQ1/INT6/PIO13 99 91 DRQ0/INT5/PIO12 100 RDC ® RISC DSP Controller R8820LV (LQFP) AD0 1 75 INT4/PIO30 AD8 2 74 MCS1/PIO15 AD1 3 73 MCS0/PIO14 AD9 4 72 DEN/PIO5 AD2 5 71 DT/R/PIO4 AD10 6 70 NMI AD3 7 69 SRDY/PIO6 AD11 8 68 HOLD AD4 9 67 HLDA AD12 10 66 WLB AD5 11 65 WHB GND 12 64 GND AD13 13 63 A0 AD6 14 62 A1 VCC 15 61 VCC AD14 16 60 A2 AD7 17 59 A3 AD15 18 58 A4 S6/CLKDIV2/PIO29 19 57 A5 UZI/PIO26 20 56 A6 TXD1/PIO27 21 55 A7 RXD1/PIO28 22 54 A8 CTS0/ENRX0/PIO21 23 53 A9 RXD0/PIO23 24 52 A10 TXD0/PIO22 25 51 A11 R8820LV Rev:1.0 RDC ® R8820LV RISC DSP Controller R8820LV Pin OUT Table Pin name AD0 AD8 AD1 AD9 AD2 AD10 AD3 AD11 AD4 AD12 AD5 GND AD13 AD6 VCC AD14 AD7 AD15 S6/ CLKDIV 2 /PI O29 LQFP Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PQFP Pin No. 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 Pin name A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 VCC A1 A0 GND WHB WLB HLDA HOLD SRDY/PI O6 LQFP Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 PQFP Pin No. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 UZI /PI O26 20 97 NMI 70 47 TXD1/PI O27 RXD1/PI O28 21 22 98 99 DT/ R /PI O4 DEN /PI O5 71 72 48 49 CTS 0 / ENRX 0 /PIO21 23 100 73 50 RXD0/PI O23 24 1 MCS0 /PI O14 MCS1 /PI O15 74 51 TXD0/PI O22 RTS 0 / RTR0 /PIO20 25 26 2 3 I NT4/ PI O30 I NT3/ INTA1 /I RQ 75 76 52 53 BHE / ADEN 27 4 I NT2/ INTA0 /PI O31 77 54 WR 28 5 I NT1/ SELECT I NT0 78 55 79 56 UCS / ONCE1 LCS / ONCE0 80 57 58 59 RD 29 6 ALE 30 7 ARDY 31 32 8 9 PCS6 /A2/PI O2 81 82 33 10 PCS5 /A1/PI O3 83 60 34 11 VCC 84 31 GND 35 12 85 62 X1 36 13 86 63 X2 VCC CLKOUTA CLKOUTB GND 37 38 39 40 41 14 15 16 17 18 PCS3 / RTS1 / RTR1 /PI O19 PCS2 / CTS1/ ENRX1 /PI O18 GND PCS1 /PI O17 PCS0 /PI O16 VCC 87 88 89 90 91 64 65 66 67 68 A19/PI O9 42 19 92 69 A18/PI O8 VCC 43 44 20 21 GND RST 93 94 70 71 A17/PI O7 A16 A15 A14 A13 A12 45 46 47 48 49 50 22 23 24 25 26 27 TMRI N1/PI O0 TMROUT1/PI O1 TMROUT0/PI O10 TMRI N0/PI O11 DRQ1/INT6/PI O13 DRQ0/INT5/PI O12 95 96 97 98 99 100 72 73 74 75 76 77 S2 S1 S0 MCS2 /PI O24 MCS3 / RFSH /PI O25 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 7 RDC ® R8820LV RISC DSP Controller 4. Pin Description Pin No.(PQFP) Symbol Type VCC Input GND Input 71 RST Input* 13 14 X1 X2 Input Output 16 CLKOUTA Output 17 CLKOUTB Output 15, 21, 38, 61, 67, 92 12, 18, 41, 64, 70, 89 Description System power: +3.3 volt power supply. System ground. Reset input. When RST is asserted, the CPU immediately terminate all operation, clears the internal registers & logic, and the address transfers to the reset address FFFF0h. Input to the oscillator amplifier. Output from the inverting oscillator amplifier. Clock output A. The CLKOUTA operation is the same as crystal input frequency (X1). CLKOUTA remains active during reset and bus hold conditions. Clock output B. The CLKOUTB operation is the same as crystal input frequency (X1). CLKOUTB remains active during reset and bus hold conditions. Asynchronous Serial Port Interface 1 RXD0/PIO23 2 TXD0/PIO22 3 RTS0 / RTR 0 /PIO20 100 CTS0 / ENRX0 /PIO21 98 TXD1/PIO27 99 RXD1/PIO28 62 PCS3 / RTS1 / RTR 1 /PIO18 Receive data for asynchronous serial port 0. This pin receives asynchronous serial data. Tranmit data for asynchronous serial port 0. This pin Output/Input transmits asynchronous serial data from the UART of the microcontrolles. Ready to send/Ready to Receive signal for asynchronous serial port 0. When the RTS0 bit in the AUXCON register is set and FC bit in the serial port 0 register is set the Output/Input RTS0 signal is enabled. Otherwise the RTS0 bit is cleared and FC bit is set the RTR 0 signal is enabled. Input/Output Clear to send/Enable Receiver Request signal for asynchronous serial port 0. when ENRX0 bit in the AUXCON register is cleared and the FC bit in the serial port Input/Output 0 control register is set the ENRX0 signal is enabled. Other when ENRX0 bit is set and the FC bit is set the ENRX0 signal is enabled. Tranmit data for asynchronous serial port 1. This pin Output/Input transmits asynchronous serial data from the UART of the microcontrolles. Receive data for asynchronous serial port 1. This pin receives Input/Output asynchronous serial data. Ready to send/Ready to Receive signal for asynchronous serial port 1. When the RTS1 bit in the AUXCON register is Output/Input set and FC bit in the serial port 1 register is set the RTS1 signal is enabled. Otherwise the RTS1 bit is cleared and FC bit is set the RTR 1 signal is enabled. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 8 RDC 63 ® R8820LV RISC DSP Controller Clear to send/Enable Receiver Request signal for asynchronous serial port 1. when ENRX0 bit in the AUXCON register is cleared and the FC bit in the serial port PCS2 / CTS1 / ENRX1 /PIO19 Input/Output 1 control register is set the ENRX1 signal is enabled. Other when ENRX1 bit is set and the FC bit is set the ENRX1 signal is enabled. Bus Interface Bus high enable/address enable. During a memory access, the BHE and (AD0 or A0) encodings indicate what type of the bus cycle. BHE is asserted during T1 and keeps the asserted to T3 and Tw. This pin is floating during bus hold and reset. 4 BHE / ADEN BHE and (AD0 or A0) Encodings AD0 or A0 Type of Bus Cycle BHE 0 0 Word transfer 0 1 High byte transfer (D15-D8) 1 0 Low byte transfer (D7-D0) Output/Input 1 1 Refresh The address portion of the AD bus can be enabled or disabled by DA bit in the LMCS and UMCS register during LCS or UCS bus cycle access, if BHE / ADEN is held high during power-on reset. The BHE / ADEN with a internal weak pull-up register, so no external pull-up register is required. The AD bus always drives both address and data during LCS or UCS bus cycle access, if the BHE / ADEN pin with external pull-low resister during reset. Write strobe. This pin indicates that the data on the bus is to 5 WR Output 6 RD Output 7 ALE Output 8 ARDY Input 9 10 11 S2 S1 S0 be written into a memory or an I/O device. WR is active during T2, T3 and Tw of any write cycle, floats during a bus hold or reset. Read Strobe. Active low signal which indicates that the microcontroller is performing a memory or I/O read cycle. RD floats during bus hold or reset. Address latch enable. Active high. This pin indicates that an address output on the AD bus. Address is guaranteed to be valid on the trailing edge of ALE. This pin is tri-stated during ONCE mode and is never floating during a bus hold or reset. Asynchronous ready. This pin performs the microcontroller that the address memory space or I/O device will complete a data transfer. The ARDY pin accepts a rising edge that is asynchronous to CLKOUTA and is active high. The falling edge of ARDY must be synchronized to CLKOUTA. Tie ARDY high, the microcontroller is always asserted in the ready condition. If the ARDY is not used, tie this pin low to yield control to SRDY. Bus cycle status. These pins are encoded to indicate the bus status. S2 can be used as memory or I/O indicator. S1 can Output be used as DT/ R indicator. These pins are floating during hold and reset. Bus Cycle Encoding Description Bus Cycle S2 S1 S0 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 9 RDC 19 20 22 23-37 39, 40 78,80,82,84,8 6,88 91,94 79,81,83,85,8 7,90 93,95 ® R8820LV RISC DSP Controller A19/PIO9 A18/PIO8 A17/PIO7 A16-A2 A1 , A0 AD0-AD7 AD8-AD15 42 WHB 43 WLB 44 HLDA 45 HOLD 46 SRDY/PIO6 48 DT/ R /PIO4 0 Interrupt acknowledge 0 0 1 Read data from I/O 0 0 0 Write data to I/O 1 0 1 Halt 1 0 0 Instruction fetch 0 1 1 Read data from memory 0 1 0 Write data to memory 1 1 1 Passive 1 1 Address bus. Non-multiplex memory or I/O address. The A bus is one-half of a CLKOUTA period earlier than the AD Output/Input bus. These pins are high-impedance during bus hold or reset. The multiplexed address and data bus for memory or I/O accessing. The address is present during the t1 clock phase, and the data bus phase is in t2-t4 cycle. The address phase of the AD bus can be disabled when the BHE / ADEN pin with external pull-Low resister during Input/Output reset. The AD bus is in high-impedance state during bus hold or reset condition and this bus also be used to load system configuration information (with pull-up or pull-Low resister) into the RESCON register when the reset input from low go high. Write high byte. This pin indicates the high byte data (AD15AD8) on the bus is to be written to a memory or I/O device. Output WHB is the logic OR of BHE , WR and AD0 inverting. This pin is floating during reset or bus hold. Write low byte. This pin indicates the low byte data (AD7AD0) on the bus is to be written to a memory or I/O device. Output WLB is the logic OR of BHE , WR and AD0. This pin is floating during reset or bus hold. Bus hold acknowledge. Active high. The microcontroller will issue a HLDA in response to a HOLD request by external bus master at the end of T4 or Ti. When the microcontroller is in hold status (HLDA is high), the AD15-AD0, A19-A0, WR , Output RD , DEN , S0 - S1 , S6 , BHE , DT/ R , WHB and WLB are floating, and the UCS , LCS , PCS6 - PCS5 , MCS3 MCS0 and PCS3 - PCS0 will be drive high. After HOLD is detected as being low, the microcontroller will lower HLDA. Bus Hold request. Active high. This pin indicates that another Input bus master is requesting the local bus. Synchronous ready. This pin performs the microcontroller that the address memory space or I/O device will complete a data transfer. The SRDY pin accepts a falling edge that is asynchronous to CLKOUTA and is active high. SRDY is Input/Output accomplished by elimination of the one-half clock period required to internally synchronize ARDY. Tie SRDY high the microcontroller is always assert in the ready condition. If the SRDY is not used, tie this pin low to yield control to ARDY. Data transmit or receive. This pin indicates the direction of Output/Input data flow through an external data-bus transceiver. DT/ R low, the microcontroller receives data. When DT/R is asserted high, the microcontroller writes data to the data bus. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 10 RDC ® R8820LV RISC DSP Controller 49 DEN /PIO5 96 S6/ CLKDIV /PIO29 97 UZI /PIO26 Data enable. This pin is provided as a data bus transceiver output enable. DEN is asserted during memory and I/O Output/Input access. DEN is drived high when DT/ R changes state. It is floating during bus hold or reset condition. Bus cycle status bit6/clock divided by 2. For S6 feature, this pin is low to indicate a microcontroller-initiated bus cycle or high to indicate a DMA-initiated bus cycle during T2, T3, Tw and T4. For CLKDIV2 feature. The internal clock of Output/Input microcontroller is the external clock be divided by 2. (CLKOUTA, CLKOUTB=X1/2), if this pin held low during power-on reset. The pin is sampled on the rising edge of RST . Upper zero indicate. This pin is the logical OR of the inverted Output/Input A19-A16. It asserts in the T1 and is held throughout the cycle. Chip Select Unit Interface 50 51 68 69 MCS0 /PIO14 MCS1 /PIO15 MCS2 /PIO24 MCS3 / RFSH /PIO25 Output/Input 57 UCS / ONCE1 Output/Input 58 LCS / ONCE0 Output/Input 59 60 PCS6 /A2/PIO2 PCS5 /A1/PIO3 Output/Input 62 63 PCS3 / RTS1 / RTR 1 /PIO19 Output/Input Midrange memory chip selects. For MCS feature, these pins are active low when enable the MMCS register to access a memory. The address ranges are programmable. MCS3 - MCS0 are held high during bus hold. When programming LMCS register, pin69 is as a RFSH pin to auto refresh the PSAM. Upper memory chip select/ONCE mode request 1. For UCS feature, this pin acts low when system accesses the defined portion memory block of the upper 512K bytes (80000hFFFFFh) memory region. UCS default acted address region is from F0000h to FFFFFh after power-on reset. The address range acting UCS is programmed by software. For ONCE1 feature. If ONCE0 and ONCE1 are sampled low on the rising edge of RST . The microcontroller enters ONCE mode. In ONCE mode, all pins are high-impedance. This pin incorporates weakly pull-up resistor. Lower memory chip select/ONCE mode request 0. For LCS feature, this pin acts low when the microcontroller accesses the defined portion memory block of the lower 512K (00000h7FFFFh) memory region. The address range acting LCS is programmed by software. For ONCE0 feature, see UCS / ONCE1 description. This pin incorporates weakly pull-up register. Peripheral chip selects/latched address bit. For PCS feature, these pins act low when the microcontroller accesses the fifth or sixth region of the peripheral memory (I/O or memory space). The base address of PCS is programmable. These pins assert with the AD address bus and are not float during bus hold. For latched address bit feature. These pins output the latched address A2, A1 when cleared the EX bit in the MCS and PCS auxiliary register. The A2, A1 retains previous latched data during bus hold. Peripheral chip selects. These pins act low when the microcontroller accesses the defined memory area of the Rev:1.0 RDC Semiconductor Co. Subject to change without notice 11 RDC 65 66 ® R8820LV RISC DSP Controller peripheral memory block (I/O or memory address). For I/O accessed, the base address can be programmed in the region 00000h to 0FFFFh. For memory address access, the base address can be located in the 1M byte memory address region. These pins assert with the multiplexed AD address bus and are not float during bus hold. PCS2 / STS1 / ENRX1 /PIO18 PCS1 /PIO17 PCS0 /PIO16 Interrupt Control Unit Interface 47 NMI Input 52 INT4/PIO30 Input/Output 53 INT3/ INTA1 /IRQ Input/Output 54 INT2/ INTA0 /PIO31 Input/Output 55 INT1/ SELECT Input/Output 56 INT0 / SO1 Input/Output Nonmaskable Interrupt. The NMI is the highest priority hardware interrupt and is nonmaskable. When this pin is asserted (NMI transition from low to high), the microcontroller always transfers the address bus to the location specified by the nonmaskable interrupt vector in the microcontroller interrupt vector table. The NMI pin must be asserted for at least one CLKOUTA period to guarantee that the interrupt is recognized. Maskable interrupt request 4. Act high. This pin indicates that an interrupt request has occurred. The microcontroller will jump to the INT4 address vector to execute the service routine if the INT4 is enable. The interrupt input can be configured to be either edge- or level-triggered. The requesting device must holt the INT4 until the request is acknowledged to guarantee interrupt recognition. Maskable interrupt request 3/interrupt acknowledge 1/slave interrupt request. For INT3 feature, except the difference interrupt line and interrupt address vector, the function of INT3 is the same as INT4. For INTA1 feature, in cascade mode or special fully-nested mode, this pin corresponds the INT1. For IRQ feature, when the microcontroller is as a slave device, this pin issues an interrupt request to the master interrupt controller. Maskable interrupt request 2/interrupt acknowledge 0. For INT2 feature, except the difference interrupt line and interrupt address vector, the function of INT2 is the same as INT4. For INTA0 feature, in cascade mode or special fully-nested mode, this pin corresponds the INT0. Maskable interrupt request 1/slave select. For INT1 feature, except the difference interrupt line and interrupt address vector, the function of INT1 is the same as INT4. For SELECT feature, when the microcontroller is as a slave device, this pin is drived from the master interrupt controller decoding. This pin acts to indicate that an interrupt appears on the address and data bus. The INT0 must act before SELECT acts when the interrupt type appears on the bus. Maskable interrupt request 0. Except the interrupt line and interrupt address vector, the function of INT0 is the same as INT4. Timer Control Unit Interface 72 75 TMRIN1/PIO0 TMRIN0/PIO11 73 74 TMROUT1/PIO1 TMROUT0/PIO10 Timer input. These pins can be as clock or control signal input, which depend upon the programmed timer mode. After Input/Output internally synchronizing low to high transitions on TMRIN, the timer controller increments. These pins must be pull-up if not being used. Timer output. Depending on timer mode select these pins Output/Input provide single pulse or continuous waveform. The duty cycle Rev:1.0 RDC Semiconductor Co. Subject to change without notice 12 RDC ® R8820LV RISC DSP Controller of the waveform can be programmable. These pins are floated during a bus hold or reset. DMA Unit Interface 76 77 DRQ1/INT6/PIO13 DRQ0/INT5/PIO12 DMA request. These pins are asserted high by an external device when the device is ready for DMA channel 1 or channel 0 to perform a transfer. These pins are level-triggered and internally synchronized. The DRQ signals must remain act until finish serviced and are not latched. Input/Output For INT6/INT5 function: When the DMA function is not being used, INT6/INT5 can be used as an additional external interrupt request. And they share the corresponding interrupt type and register control bits. The INT6/5 are edge-triggered only and must be hold until the interrupt is acknowledged. Notes: 1.When enable the PIO Data register, there are 32 MUX definition pins can be as a PIO pin. For example, the DRD1/PIO13 (pin76) can be as a PIO13 when enable the PIO Data register. 2.The PIO status during Power-On reset : PIO1, PIO10, PIO22, PIO23 are input with pull-down, PIO4 to PIO9 are normal operation and the others are input with pull-up. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 13 RDC ® R8820LV RISC DSP Controller 5. Basic Application System Block & Read/Write timing Diagram Flash ROM AD15-AD0 Data(16) A19-A1 X1 Address WR WE RD OE UCS CE X2 SRAM RS232 Serial port0 Level Data(16) Converter Address R8820LV RS232 WE Serial port1 Level OE Converter LCS CE Timer0-1 Peripheral INTx Data DMA VCC Address PIO PCSx CS 100K WE RST OE 1uF BASIC APPLICATION SYSTEM BLOCK (A) Flash ROM AD15-AD0 Low Byte D15-D8 D7-D0 Address Address RD OE OE UCS CE CE WHB WE WE A19-A1 X1 High Byte X2 WLB RS232 Level SRAM Serial port0 High Byte Low Byte Converter D15-D8 RS232 Level R8820LV Address Serial port1 LCS Converter D7-D0 Address OE OE CE CE WE WE Timer0-1 INTx Peripheral DMA VCC Data PIO Address PCSx CS WR WE 100K RST OE 1uF BASIC APPLICATION SYSTEM BLOCK (B) Rev:1.0 RDC Semiconductor Co. Subject to change without notice 14 RDC ® R8820LV RISC DSP Controller T1 T2 T3 CLKOUTA T4 TW A19:A0 ADDRESS S6 AD15:AD0 ADDRESS DATA ALE RD BHE UCS,LCS PCSx,MCSX DEN DT/R S2:S0 STATUS UZI READ CYCLE Rev:1.0 RDC Semiconductor Co. Subject to change without notice 15 RDC ® R8820LV RISC DSP Controller T1 T2 T3 CLKOUTA T4 TW A19:A0 ADDRESS S6 AD15:AD0 ADDRESS DATA ALE WR WHB,WLB BHE UCS,LCS PCSx,MCSX DEN DT/R S2:S0 STATUS UZI WRITE CYCLE Rev:1.0 RDC Semiconductor Co. Subject to change without notice 16 RDC ® R8820LV RISC DSP Controller 6. Oscillator Characteristics & System Clock X1 Rf C1 X2 R8820LV C2 L C3 200PF For fundamental-mode crystal: For third-overtone mode crystal: C1 -------------- 20pF ± 20% C1 -------------- 20pF ± 20% C2 -------------- 20pF ± 20% C2 -------------- 20pF ± 20% Rf --------------- 1 mega-ohm C3 -------------- 200pf C3 -------------- Don’t care Rf --------------- 1 mega-ohm L --------------- 3.0uH ± 20% (40MHz) L -------------- Don’t care 4.7uH ± 20% (33MHz) 8.2uH ± 20% (25MHz) 12uH ± 20% (20MHZ) Rev:1.0 RDC Semiconductor Co. Subject to change without notice 17 RDC ® R8820LV RISC DSP Controller 7. Execution Unit 7.1 General Register The R8820LV has eight 16-bit general registers. And the AX,BX,CX,DX can be subdivided into two 8-bit register (AH,AL,BH, BL,CH,CL,DH,DL). The functions of these registers are described as follows. AX : Word Divide , Word Multiply, Word I/O operation. AH : Byte Divide , Byte Multiply, Byte I/O , Decimal Arithmetic, Translate operation. AL : Byte Divide , Byte Multiply operation. BX : Translate operation. CX : Loops, String operation CL : Variable Shift and Rotate operation. DX : Word Divide , Word Multiply, Indirect I/O operation SP : Stack operations (POP, POPA, POPF, PUSH, PUSHA, PUSHF) BP : General-purpose register which can be used to determine offset address of operands in Memory. SI : String operations DI : String operations High 15 Data Group Index Group and Pointer Low 8 7 0 AX AH AL Accumulator BX BH BL Base Register CX CH CL Count/Loop/Repeat/Shift DX DH DL Data SP Stack Pointer BP Base Pointer SI Source Index DI Destination Index GENERAL REGISTERS 7.2 Segment Register R8820LV has four 16-bit segment registers, CS, DS, SS, ES. The segment registers contain the base addresses (starting location) of these memory segments, and they are immediately addressable for code (CS), data (DS & ES), and stack (SS) memory. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 18 RDC ® R8820LV RISC DSP Controller CS (Code Segment) : The CS register points to the current code segment, which contains instruction to be fetched. The default location memory space for all instruction is 64K. The initial value of CS register is 0FFFFh. DS (Data Segment) : The DS register points to the current data segment, which generally contains program variables. The DS register initialize to 0000H. SS (Stack Segment ) : The SS register points to the current stack segment, which is for all stack operations, such as pushes and pops. The stack segment is used for temporary space. The SS register initialize to 0000H. ES (Extra Segment) : The ES register points to the current extra segment which is typically for data storage, such as large string operations and large data structures. The DS register initialize to 0000H. 15 8 7 0 CS Code Segment DS Data Segment SS Stack Segment ES Extra Segment SEGMENT REGISTERS 7.3 Instruction Pointer and Status Flags Register IP (Instruction Pointer) : The IP is a 16-bit register and it contains the offset of the next instruction to be fetched. Software can not to direct access the IP register and this register is updated by the Bus Interface Unit. It can change, be saved or be restored as a result of program execution. The IP register initialize to 0000H and the CS:IP starting execution address is at 0FFFF0H. FLAGS Reset Value : 0000h Processor Status Flags Registers 15 14 13 12 Reserved 11 10 9 8 7 6 5 4 3 2 1 0 OF DF IF TF SF ZF Res AF Res PF Res CF These flags reflect the status after the Execution Unit is executed. Bit 15-12 : Reserved Bit 11: OF, Overflow Flag. An arithmetic overflow has occurred, this flag will be set. Bit 10 : DF, Direction Flag. If this flag is set, the string instructions are increment address process. If DF is cleared, the string instructions are decrement address process. Refer the STD and CLD instructions for how to set and clear the DF flag. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 19 RDC ® R8820LV RISC DSP Controller Bit 9 : IF, Interrupt-Enable Flag. Refer the STI and CLI instructions for how to set and clear the IF flag. Set to 1 : The CPU enables the maskable interrupt request. Set to 0 : The CPU disables the maskable interrupt request. Bit 8: TF, Trace Flag. Set to enable single-step mode for debugging; Clear to disable the single-step mode. If an application program sets the TF flag using POPF or IRET instruction, a debug exception is generated after the instruction (The CPU automatically generates an interrupt after each instruction) that follows the POPF or IRET instruction. Bit 7: SF, Sign Flag. If this flag is set, the high-order bit of the result of an operation is 1,indicating it is negative. Bit 6: ZF, Zero Flag. The result of operation is zero, this flag is set. Bit 5: Reserved Bit 4: AF, Auxiliary Flag. If this flag is set, there has been a carry from the low nibble to the high or a borrow from the high nibble to the low nibble of the AL general-purpose register. Used in BCD operation. Bit 3: Reserved. Bit 2: PF, Parity Flag. The result of low-order 8 bits operation has even parity, this flag is set. Bit 1: Reserved Bit 0: CF, Carry Flag. If CF is set, there has been a carry out or a borrow into the high-order bit of the instruction result. 7.4 Address generation The Execution Unit generates a 20-bit physical address to Bus Interface Unit by the Address Generation. Memory is organized in sets of segments. Each segment contains a 16 bits value. Memory is addressed using a two-component address that consists of a 16-bit segment and 16-bit offset. The Physical Address Generation figure describes how the logical address transfers to the physical address. Shift left 4 bits 1 2 F 15 1 2 F 9 19 0 0 0 1 15 1 0 2 0 9 Segment Base 0 0 1 15 2 Logical Address Offset 0 2 0 F A 19 2 Physical Address 0 TO Memory Physical Address Generation Rev:1.0 RDC Semiconductor Co. Subject to change without notice 20 RDC ® R8820LV RISC DSP Controller 8. Peripheral Control Block Register The peripheral control block can be mapped into either memory or I/O space which is to program the FEh register. And it starts at FF00h in I/O space when reset the microprocessor. The following table is the definition of all the peripheral Control Block Register , and the detail description will arrange on the relation Block Unit. Offset (HEX) FE F6 F4 F2 F0 E6 E4 E2 E0 DA D8 D6 D4 D2 D0 CA C8 C6 C4 C2 C0 A8 A6 A4 A2 A0 88 86 84 82 80 7A 78 76 74 72 Register Name Peripheral Control Block Relocation Register Reset Configuration Register Processor Release Level Register Auxiliary configuration Register System configuration register Watchdog timer control register Enable RCU Register Clock Prescaler Register Memory Partition Register DMA 1 Control Register DMA 1 Transfer Count Register DMA 1 Destination Address High Register DMA 1 Destination Address Low Register DMA 1 Source Address High Register DMA 1 Source Address Low Register DMA 0 Control Register DMA 0 Transfer Count Register DMA 0 Destination Address High Register DMA 0 Destination Address Low Register DMA 0 Source Address High Register DMA 0 Source Address Low Register PCS and MCS Auxiliary Register Midrange Memory Chip Select Register Peripheral Chip Select Register Low Memory Chip Select Register Upper Memory Chip Select Register Serial Port 0 Baud Rate Divisor Register Serial Port 0 Receive Register Serial Port 0 Transmit Register Serial Port 0 Status Register Serial Port 0 Control Register PIO Data 1 Register PIO Direction 1 Register PIO Mode 1 Register PIO Data 0 Register PIO Direction 0 Register Page 22 25 22 30 23 68 80 80 80 56 58 58 59 59 59 55 55 55 56 56 56 34 33 35 32 31 75 75 74 74 72 78 78 78 79 79 Offset (HEX) 70 66 62 60 5E 5C 5A 58 56 54 52 50 44 42 40 3E 3C 3A 38 36 34 32 30 2E 2C 2A 28 26 24 22 20 18 16 14 12 10 Register Name Page PIO Mode 0 Register Timer 2 Mode / Control Register Timer 2 Maxcount Compare A Register Timer 2 Count Register Timer 1 Mode / Control Register Timer 1 Maxcount Compare B Register Timer 1 Maxcount Compare A Register Timer 1 Count Register Timer 0 Mode / Control Register Timer 0 Maxcount Compare B Register Timer 0 Maxcount Compare A Register Timer 0 Count Register Serial Port 0 interrupt control register Serial port 1 interrupt control register INT4 Control Register INT3 Control Register INT2 Control Register INT1 Control Register INT0 Control Register DMA 1/INT6 Interrupt Control Register DMA 0/INT5 Interrupt Control Register Timer Interrupt Control Register Interrupt Status Register Interrupt Request Register Interrupt In-service Register InterruptPriority Mask Register Interrupt Mask Register Interrupt Poll Status Register Interrupt Poll Register Interrupt End-of-Interrupt Interrupt Vector Register Serial port 1 baud rate divisor Serial port 1 receive register Serial port 1 transmit register Serial port 1 status register Serial port 1 control register 79 65 66 66 63 65 65 65 62 63 63 62 40 41 42 42 43 43 44 45 45 46 47 47 48 49 50 51 51 52 52 76 76 76 75 75 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 21 RDC ® R8820LV RISC DSP Controller Peripheral Control Block Relocation Register: 15 14 13 12 Res S/M Res M/IO 11 10 9 8 7 Offset : FEh Reset Value : 20FFh 6 5 4 3 2 1 0 R19 - R8 The peripheral control block is mapped into either memory or I/O space by programming this register. When the other chip selects ( PCSx or MCSx ) are programmed to zero wait states and ignore the external ready, the PCSx or MCSx can overlap the control block. Bit 15: Reserved Bit 14: S/ M , Slave/Master – Configures the interrupt controller set 0 : Master mode, set 1: Slaved mode Bit 13 : Reserved Bit 12: M/ IO , Memory/IO space. At reset, this bit is set to 0 and the PCB map start at FF00h in I/O space. set 1- The peripheral control block (PCB) is located in memory space. set 0- The PCB is located in I/O space. Bit 11-0 : R19-R8 , Relocation Address Bits The upper address bits of the PCB base address. The lower eight bits default to 00h. When the PCB is mapped to I/O space, the R19-R16 must be programmed to 0000b. Offset : F4h Reset Value : F9h Processor Release Level Register 15 14 13 12 11 10 9 PRL 8 7 6 5 4 3 2 1 0 1 1 0 1 1 0 0 1 Read only register that specifies the processor release version and RDC identify number Bit 15-8 : Processor version 01h : version A , 02h : version B, 03h : version C, 04h : version D Bit 7-0 : RDC identify number - D9h Rev:1.0 RDC Semiconductor Co. Subject to change without notice 22 RDC ® R8820LV RISC DSP Controller 9. System Clock Block PSEN(F0h.15) enable/disable X1 CLKIN X2 CLKIN or CLKIN/2 Microprocessor Internal Clock CLOCK Divisior (CLK/2-CLK/128) CLK MUX CLKOUTA CAD(F0h.8) CLKIN/2 Select Divisor Select CAF(F0h.9) F2-F0(F0h.2-F0h.0) S6/CLKDIV2 MUX CLKOUTB CBD(F0h.10) CBF(F0h.11) System Clock Offset : F0h Reset Value : 0000h 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PSEN MCSBIT Power-Save Control Register 0 0 CBF CBD CAF CAD 0 0 0 0 0 F2 F1 F0 Bit 15: PSEN , Enable Power-save Mode. This bit is cleared by hardware when an external interrupt occurs. This bit does not be changed when software interrupts (INT instruction) and exceptions occurs. Set 1: enable power-save mode and divides the internal operating clock by the value in F2-F0. Bit14 : MCSBIT, MCS0 control bit. Set to 0: The MCS0 operate normally. Set to 1: MCS0 is active over the entire MCSx range Bit13-12: Reserved Bit 11: CBF, CLKOUTB Output Frequency selection. Set 1: CLKOUTB output frequency is same as crystal input frequency. Set 0 : CLKOUTB output frequency is from the clock divisor, which frequency is same as that of microprocessor internal clock. Bit 10 : CBD, CLKOUTB Drive Disable Set 1: Disable the CLKOUTB. This pin will be three-state. Set 0 : Enable the CLKOUTB. Bit 9: CAF, CLKOUTA Output Frequency selection. Set 1: CLKOUTA output frequency is same as crystal input frequency. Set 0 : CLKOUTB output frequency is from the clock divisor, which frequency is same as that of microprocessor Rev:1.0 RDC Semiconductor Co. Subject to change without notice 23 RDC ® R8820LV RISC DSP Controller internal clock . Bit 8: CAD, CLKOUTA Drive Disable. Set 1: Disable the CLKOUTA. This pin will be three-state. Set 0 : Enable the CLKOUTA. Bit 7-3 : Reserved Bit 2-0: F2- F0, Clock Divisor Select. F2, F1, F0 ----- Divider Factor 0, 0, 0 ---- Divide by 1 0, 0, 1 ---- Divide by 2 0, 1, 0 ---- Divide by 4 0, 1, 1 ---- Divide by 8 1, 0, 0 ---- Divide by 16 1, 0, 1 ---- Divide by 32 1, 1, 0 ---- Divide by 64 1, 1, 1 ---- Divide by 128 10. Reset Processor initialization is accomplished with activation of the RST pin. To reset the processor, this pin should be held low for at least seven oscillator periods. The Reset Status Figure shows the status of the RST pin and others relation pins. When RST from low go high , the state of input pin (with weakly pull-up or pull-down) will be latched , and each pin will perform the individual function. The AD15-AD0 will be latched into the register F6h. UCS / ONCE1 , LCS / ONCE0 will enter ONCE mode (All of the pins will floating except X1 , X2) when with pull-low resisters. The input clock will divide by 2 when S6/ CLKDIV2 with pull-low resister. The AD15-AD0 bus will not drive the address phase during UCS , LCS cycle if BHE / ADEN with pull-low resister Rev:1.0 RDC Semiconductor Co. Subject to change without notice 24 RDC ® R8820LV RISC DSP Controller CLKOUTA RST min 7T A19-A0 ffff0 (float) (input) S6 AD15-AD0 (input) ea fff0 ALE (float) (float) RD (input) BHE (input) UCS (float) DEN DT/R (float) S2-S0 7 (float) 4 7 4 Reset Status Offset : F6h Reset Value : AD15-AD0 Reset Configuration Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RC Bit 15- 0 : RC ,Reset Configuration AD15 – AD0. The AD15 to AD0 must with weakly pull-up or pull-down resistors to correspond the contents when AD15-AD0 be latched into this register during the RST pin from low go high. And the value of the reset configuration register provides the system information when software read this register. This register is read only and the contents remain valid until the next processor reset. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 25 RDC ® R8820LV RISC DSP Controller 11. Bus Interface Unit The bus interface unit drives address, data, status and control information to define a bus cycle. The bus A19-A0 are nonmultiplex memory or I/O address. The AD15-AD0 are multiplexed address and data bus for memory or I/O accessing. The S2 - S1 are encoded to indicate the bus status, which is described in the Pin Description table in page 5. The Basic Application System Block (page 10) and Read/Write Timing Diagram (page 12) describe the basic bus operation. 11.1 Memory and I/O interface The memory space consists of 1M bytes (512k 16-bit port) and the I/O space consists of 64k bytes (32k 16-bit port). Memory devices exchange information with the CPU during memory read, memory write and instruction fetch bus cycles. I/O read and I/O write bus cycles use a separate I/O address space. Only IN/OUT instruction can access I/O address space, and information must be transferred between the peripheral device and the AX register. The first 256 bytes of I/O space can be accessed directly by the I/O instructions. The entire 64k bytes I/O address space can be accessed indirectly, through the DX register. I/O instructions always force address A19-A16 to low level. FFFFFH Memory Space 1M Bytes 0FFFFH I/O Space 0 64K Bytes 0 Memory and I/O Space A19:1 512K Bytes FFFFF FFFFD 512K Bytes FFFFE FFFFC 5 3 1 4 2 0 D15:8 BHE D7:0 A0 Physical Data Bus Models 11.2 Data Bus The memory address space data bus is physically implemented by dividing the address space into two banks of up to 512k bytes. Each one bank connects to the lower half of the data bus and contains the even-addressed bytes (A0=0). The other Rev:1.0 RDC Semiconductor Co. Subject to change without notice 26 RDC ® R8820LV RISC DSP Controller bank connects to the upper half of the data bus and contains odd-addressed bytes (A0=1). A0 and BHE determine whether one bank or both banks participate in the data transfer. 11.3 Wait States Wait states extend the data phase of the bus cycle. The ARDY or SRDY input with high level will insert wait states. To avoid wait states, ARDY and SRDY must be low within a specified setup time prior to phase 2 of T2. To insert wait states, ARDY or SRDY must drive high within a specified setup time prior to phase 2 of T2 or phase 1 of T3. If the ARDY is not used, tie this pin low to yield control to SRDY. If the SRDY is not used, tie this pin low to yield control to ARDY. The SRDY/PIO6 is multi function pin, and SRDY internally pull-down when this pin is programmed for PIO function. Case 1 TW TW TW T4 Case 2 T3 TW TW T4 Case 3 T2 T3 TW T4 Case 4 T1 T2 T3 T4 CLKOUTA ARDY(Normally Not-Ready System) ARDY(Normally Ready System) Asynchronous Ready Waveforms Case 1 TW TW TW T4 Case 2 T3 TW TW T4 Case 3 T2 T3 TW T4 Case 4 T1 T2 T3 T4 CLKOUTA SRDY(Normally Not-Ready System) SRDY(Normally Ready System) Synchronous Ready Waveforms Rev:1.0 RDC Semiconductor Co. Subject to change without notice 27 RDC ® R8820LV RISC DSP Controller 11.4 Bus Hold When the bus hold requested ( HOLD pin active high) by the another bus master, the microprocessor will issue a HLDA in response to a HOLD request at the end of T4 or Ti. When the microprocessor is in hold status (HLDA is high), the AD15AD0, A19-A0, WR , RD , DEN , S1 - S0 , S6 , BHE , DT/ R , WHB and WLB are floating, and the UCS , LCS , PCS6 PCS5 , MCS3 - MCS0 and PCS3 - PCS0 will be drive high. After HOLD is detected as being low, the microprocessor will lower the HLDA. Case 1 Case 2 Ti T3 Ti T4 Ti Ti Ti Ti CLKOUTA HOLD HLDA AD15:AD0 Floating Floating A19:A0 Floating DEN Floating S6 Floating RD Floating WR Floating DT/R S2:S0 7 2 Floating Floating WLB BUS HOLD ENTER WAVEFORM Rev:1.0 RDC Semiconductor Co. Subject to change without notice 28 RDC ® R8820LV RISC DSP Controller Case 1 Case 2 Ti Ti Ti Ti Ti Ti Ti T4 T1 T1 CLKOUTA HOLD HLDA AD15:AD0 A19:A0 Floating DATA Floating ADDRESS Floating DEN S6 RD WR DT/R S2:S0 WLB Floating Floating Floating Floating Floating 7 6 Floating BUS HOLD LEAVE WAVEFORM Rev:1.0 RDC Semiconductor Co. Subject to change without notice 29 RDC ® R8820LV RISC DSP Controller 11.5 Bus Width The R8820LV default is 16 bits bus access. And the bus can be programmed as 8-bits or 16-bits access during memory or I/O access is located in the LCS or MCSx or PCSx address space. The UCS code- fetched selection is 16 bits bus width, which can not be changed by programmed the register. Offset : F2h Reset Value : 0000h 14 13 12 11 10 9 8 7 Reserved 6 5 4 RTS1 ENRX0 15 ENRX1 Auxiliary configuration Register 3 2 RTS0 LSIZ 1 0 MSIZ IOSIZ Bit 15-7: Reserved. Bit 6: ENRX1, Enable the Receiver Request of Serial port 1. Set 1: The CTS1 / ENRX1 pin is configured as ENRX1 Set 0: The CTS1 / ENRX1 pin is configured as CTS1 Bit 5: RTS1, Enable Request to Send of Serial port 1. Set 1: The RTR 1 / RTS1 pin is configured as RTS1 Set 0: The RTR 1 / RTS1 pin is configured as RTR 1 Bit 4: ENRX0, Enable the Receiver Request of Serial port 0. Set 1: The CTS0 / ENRX0 pin is configured as ENRX0 Set 0: The CTS0 / ENRX0 pin is configured as CTS0 Bit 3: RTS0, Enable Request to Send of Serial port 0. Set 1: The RTR 0 / RTS0 pin is configured as RTS0 Set 0: The RTR 0 / RTS0 pin is configured as RTR 0 Bit 2: LSIZ, LCS Data Bus Size selection. This bit can not be changed while executing from LCS space or while the Peripheral Control Block is overlaid with PCS space. Set 1: 8 bits data bus access when the memory access located in the LCS memory space. Set 0: 16 bits data bus access when the memory access located in the LCS memory space. Bit 1: MSIZ, MCSx , PCSx Memory Data Bus Size selection. This bit can not be changed while executing from the associated or while the Peripheral Control Block is overlaid on this address space. Set 1: 8 bits data bus access when the memory access locate in the selection memory space. Set 0 : 16 bits data bus access when the memory access locate in the selection memory space. Bit 0: IOSIZ, I/O Space Data Bus Size selection. This bit determines the width of the data bus for all I/O space accesses. Set 1: 8 bits data bus access. Set 0 : 16 bits data bus access. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 30 RDC ® R8820LV RISC DSP Controller 12. Chip Select Unit The Chip Select Unit provides 12 programmable chip select pins to access a specific memory or peripheral device. The chip selects are programmed through five peripheral control registers (A0h, A2h, A4h, A6h, A8h). And all of the chip selects can be insert wait states by programmed the peripheral control register. 12.1 UCS The UCS default to active on reset for program code access. The memory active range is upper 512k (80000h – FFFFFh), which is programmable. And the default memory active range of UCS is 64k ( F0000h – FFFFFh). The UCS active to drive low four CLKOUTA oscillators if no wait state inserts. There are three wait-states insert to UCS active cycle on reset. Offset : A0h Reset Value :F03Bh Upper Memory Chip Select Register 15 1 14 13 12 LB2 - LB0 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 DA 0 1 1 1 R2 R1 R0 Bit 15 : Reserved Bit 14-12 : LB2-LB0, Memory block size selection for UCS chip select pin. The UCS chip select pin active region can be configured by the LB2-LB0. The default memory block size is from F0000h to FFFFFh. LB2, LB1, LB0 ---- Memory Block size , Start address, End Address 1, 1, 1 ---- 64k , F0000h , FFFFFh 1, 1 , 0 ---- 128k , E0000h , FFFFFh 1, 0 , 0 ---- 256k , C0000h , FFFFFh 0, 0 , 0 ---- 512k , 80000h , FFFFFh Bit 11-8 : Reserved Bit 7 : DA , Disable Address. If the BHE / ADEN pin is held high on the rising edge of RST , then the DA bit is valid to enable/disable the address phase of the AD bus. If the BHE / ADEN pin is held high on the rising edge of RST , the AD bus always drive the address and data. Set 1 : Disable the address phase of the AD15 – AD0 bus cycle when UCS is asserted. Set 0 : Enable the address phase of the AD15 – AD0 bus cycle when UCS is asserted. Bit 6-3: Reserved Bit 2 : R2, Ready Mode. This bit is used to configure the ready mode for UCS chip select. Set 1: external ready is ignored. Set 0: external ready is required. Bit 1-0 : R1-R0, Wait-State value. When R2 is set to 0, it can inserted wait-state into an access to the UCS memory area. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 31 RDC ® R8820LV RISC DSP Controller (R1,R0) = (0,0) -- 0 wait-state ; (R1,R0) = (0,1) -- 1 wait-state (R1,R0) = (1,0) -- 2 wait-state ; (R1,R0) = (1,1) -- 3 wait-state 12.2 LCS The lower 512k bytes (00000h-7FFFFh) memory region chip selects. The memory active range is programmable, which has no default size on reset. So the A2h register must be programmed first before to access the target memory range. The LCS pin is not active on reset, but any read or write access to the A2h register activates this pin. Offset : A2h Reset Value : Low Memory Chip Select Register 15 0 14 13 12 UB2 - UB0 11 10 9 8 7 6 5 4 3 2 1 0 1 1 1 1 DA PSE 1 1 1 R2 R1 R0 Bit 15: Reserved Bit 14-12 : UB2-UB0, Memory block size selection for LCS chip select pin The LCS chip select pin active region can be configured by the UB2-UB0. The LCS pin is not active on reset, but any read or write access to the A2h (LMCS) register activates this pin. UB2, UB1, UB0 ---- Memory Block size , Start address, End Address 0, 0 , 0 ---- 64k , 00000h , 0FFFFh 0, 0 , 1 ---- 128k , 00000h , 1FFFFh 0, 1 , 1 ---- 256k , 00000h , 3FFFFh 1, 1 , 1 ---- 512k , 00000h , 7FFFFh Bit 11-8 : Reserved Bit 7 : DA , Disable Address. If the BHE / ADEN pin is held high on the rising edge of RST , then the DA bit is valid to enable/disable the address phase of the AD bus. If the BHE / ADEN pin is held low on the rising edge of RST , the AD bus always drive the address and data. Set 1 : Disable the address phase of the AD15 – AD0 bus cycle when LCS is asserted. Set 0 : Enable the address phase of the AD15 – AD0 bus cycle when LCS is asserted. Bit 6 : PSE, PSRAM Mode Enable. This bit is used to enable PSRAM support for the LCS chip select memory space. The refresh control unit registers E0h,E2h,E4h must be configured for auto refresh before PSRAM support is enabled. PSE set to 1: PSRAM support is enable PSE set to 0: PSRAM support is disable Bit 5-3: Reserved Bit 2 : R2, Ready Mode. This bit is used to configure the ready mode for LCS chip select. Set 1: external ready is ignored. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 32 RDC ® R8820LV RISC DSP Controller Set 0: external ready is required. Bit 1-0 : R1-R0, Wait-State value. When R2 is set to 0, it can inserted wait-state into an access to the LCS memory area. (R1,R0) = (0,0) -- 0 wait-state ; (R1,R0) = (0,1) -- 1 wait-state (R1,R0) = (1,0) -- 2 wait-state ; (R1,R0) = (1,1) -- 3 wait-state 12.3 MCSx The memory block of MCS4 - MCS0 can be located anywhere within the 1M bytes memory space, exclusive of the areas associated with the UCS and LCS chip selects. The maximum MCSx active memory range is 512k bytes. The MCSx chip selects are programmed through two registers A6h and A8h, and these select pins are not active on reset. Both A6h and A8h registers must be accessed with a read or write to activate MCS4 - MCS0 . There aren’t default value on A6h and A8h registers, so the A6h and A8h must be programmed first before MCS4 - MCS0 active. Offset : A6h Reset Value : Midranage Memory Chip Select Register 15 14 13 12 11 10 9 8 BA19 - BA13 7 6 5 4 3 2 1 0 1 1 1 1 1 R2 R1 R0 Bit 15-7 : BA19-BA13, Base Address. The BA19-BA13 correspond to bits 19-13 of the 1M bytes (20-bits) programmable base address of the MCS chip select block. The bits 12 to 0 of the base address are always 0. The base address can be set to any integer multiple of the size of the memory block size selected in these bits. For example, if the midrange block is 32Kbytes, only the bits BA19 to BA15 can be programmed. So the block address could be locate at 20000h or 38000h but not in 22000h. The base address of the MCS chip select can be set to 00000h only if the LCS chip select is not active. And the MCS chip select address range is not allowed to overlap the LCS chip select address range. The MCS chip select address range also is not allowed to overlap the UCS chip select address range. Bit 8-3 : Reserved Bit 2: R2, Ready Mode. This bit is configured to enable/disable the wait states inserted for the MCS chip selects. The R1,R0 bits of this register determine the number of wait state to insert. set to 1: external ready is ignored set to 0: external ready is required Bit 1-0 : R1-R0, Wait-State value. The R1,R0 determines the number of wait states inserted into a MCS access. (R1,R0) : (1,1) – 3 wait states , (1,0) – 2 wait states, (0,1) – 1 wait states , (0,0) – 0 wait states Rev:1.0 RDC Semiconductor Co. Subject to change without notice 33 RDC ® R8820LV RISC DSP Controller Offset : A8h Reset Value : PCS and MCS Auxiliary Register 15 14 13 12 1 11 10 9 8 M6 - M0 7 6 5 4 3 2 1 0 EX MS 1 1 1 R2 R1 R0 Bit 15: Reserved Bit 14-8: M6-M0, MCS Block Size. These bits determines the total block size for the MCS3 - MCS0 chip selects. Each individual chip select is active for one quarter of the total block size. For example, if the block size is 32K bytes and the base address is located at 20000h. The individual active memory address range of MCS3 to MCS0 is MCS0 – 20000h to 21FFF, MCS1-22000 to 23FFFh, MCS2 - 24000h to 25FFFh, MCS3 - 26000h to 27FFFh. MCSx total block size is defined by M6-M0, M6-M0 , Total block size, MCSx address active range 0000001b , 8k , 2k 0000010b , 16k , 4k 0000100b , 32k , 8k 0001000b , 64k , 16k 0010000b , 128k , 32k 0100000b , 256k , 64k 1000000b , 512k , 128k Bit 7 : EX, Pin Selector. This bit configures the multiplex output which the PCS6 - PCS5 pins as chip selects or A2-A1. Set 1 : PCS6 , PCS5 are configured as peripheral chip select pins. Set 0: PCS6 is configured as address bit A2, PCS5 is configured as A1. Bit 6: MS, Memory or I/O space Selector. Set 1: The PCSx pins are active for memory bus cycle. Set 0: The PCSx pins are active for I/O bus cycle. Bit 5-3 : Reserved Bit 2 : R2, Ready Mode. This bit is configured to enable/disable the wait states inserted for the PCS5,PCS6 chip selects. The R1,R0 bits of this register determine the number of wait state to insert. set to 1: external ready is ignored set to 0: external ready is required Bit 1-0 : R1-R0, Wait-State value. The R1,R0 determines the number of wait states inserted into a PCS5 - PCS6 access. (R1,R0) : (1,1) – 3 wait states , (1,0) – 2 wait states, (0,1) – 1 wait states , (0,0) – 0 wait states 12.4 PCSx The peripheral or memory chip selects which are programmed through A4h and A8h register to define these pins. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 34 RDC ® R8820LV RISC DSP Controller The base address memory block can be located anywhere within the 1M bytes memory space, exclusive of the areas associated with the MCS4 , LCS and MCS chip elects. If the chip selects are mapped to I/O space, the access range is 64k bytes. PCS6 – PCS5 can be configured from 0 wait-state to 3 wait-states. PCS3 – PCS0 can be configured from 0 wait-state to 15 wait-states. Offset : A4h Reset Value : Peripheral Chip Select Register 15 14 13 12 11 10 9 8 7 BA19 - BA11 6 5 4 3 2 1 0 1 1 1 R3 R2 R1 R0 Bit 15-7 : BA19-BA11, Base Address. BA19-BA11 correspond to bit 19-11 of the 1M bytes (20-bits) programmable base address of the PCS chip select block. When the PCS chip selects are mapped to I/O space, BA19-BA16 must be wrote to 0000b because the I/O address bus in only 64K bytes (16-bits) wide. PCSx address range: PCS0 : Base Address - Base Address+255 PCS1 : Base Address+256 - Base Address+511 PCS2 : Base Address+512 - Base Address+767 PCS3 : Base Address+768 - Base Address+1023 PCS4 : Base Address+1280 - Base Address+1535 PCS5 : Base Address+1536 - Base Address+1791 Bit 6-4: Reserved Bit 3: R3; Bit 1-0: R1,R0 ,Wait-State Value. The R3,R1,R0 determines the number of wait-states inserted into a PCS3 PCS0 access. R3, R1, R0 -- Wait States 0, 0, 0 -- 0 0, 0, 1 -- 1 0, 1, 0 -- 2 0, 1, 1 -- 3 1, 0, 0 -- 5 1, 0, 1 -- 7 1, 1, 0 -- 9 1, 1, 1 -- 15 Bit 2 : R2, Ready Mode. This bit is configured to enable/disable the wait states inserted for the PCS3 - PCS0 chip selects. The R3,R1,R0 bits determine the number of wait state to insert. set to 1: external ready is ignored Rev:1.0 RDC Semiconductor Co. Subject to change without notice 35 RDC ® R8820LV RISC DSP Controller set to 0: external ready is required Rev:1.0 RDC Semiconductor Co. Subject to change without notice 36 RDC ® R8820LV RISC DSP Controller 13. Interrupt Controller Unit There are 16 interrupt requests source connect to the controller: 7 maskable interrupt pins ( INT0 – INT6); 2 non-maskable interrupts (NMI pin , WDT) ; 7 internal unit request source ( Timer 0, 1,2 ;DMA 0,1 ; Asynchronous serial port 0, 1). Master/Slave Mode Select (FEH.14) Timer0/1/2 Interrupt REQ. 0 Timer0 REQ. 1 INT0 0 Timer1 REQ. 1 Interrupt Type Execation Unit Interrupt REQ. NMI NMI Watchdog Timer 0 1 Timer2 REQ. DMA0 Interrupt REQ. Interrupt Control Logic INT5 DMA1 Interrupt REQ. 16 Bit INT6 INT2 INT3 EOI Register INT4 Acknowledge Asynchronous Serial Port 0 In-Service Register Asynchronous Serial Port 1 16 Bit Acknowledge to DMA, Timer,Serial port Unit Internal Address/Data Bus Interrupt Control Unit Block Diagram 13.1 Master Mode and Slave Mode The interrupt controller can be programmed as a master or slave mode. (program FEh , bit 14). The master mode has two connections : Fully Nested Mode connection or Cascade Mode connection. INT0 INT1 INT2 INT3 INT4 INT5 INT6 Interrupt Interrupt Interrupt Interrupt Interrupt Interrupt Interrupt Source Source Source Source Source Source Source R8820LV Fully Nested Mode Connections Rev:1.0 RDC Semiconductor Co. Subject to change without notice 37 RDC ® R8820LV RISC DSP Controller Interrupt Sources INT IR7 INT0 INT4 8259 INT5 8259 INT6 INTA Interrupt Sources CAS3-CAS0 INTA0 CAS3-CAS0 R8820LV IR7 INT1 Interrupt Sources 8259 8259 INTA1 INT CAS3-CAS0 INTA Interrupt Sources CAS3-CAS0 Cascade Mode Connection INT0 8259 INTA0 R8820LV Cascade Address Dccode Select IRQ Slave Mode Connection 13.2 Interrupt Vector, Type and Priority The following table shows the interrupt vector addresses, type and the priority. The maskable interrupt priority can be changed by programmed the priority register. The Vector addresses for each interrupt are fixed. Interrupt source Interrupt Vector EOI Priority Type Address Type Divide Error Exception 00h 00h 1 Trace interrupt 01h 04h 1-1 * NMI 02h 08h 1-2 * Breakpoint Interrupt 03h 0Ch 1 Note Rev:1.0 RDC Semiconductor Co. Subject to change without notice 38 RDC ® R8820LV RISC DSP Controller INTO Detected Over Flow Exception Array Bounds Exception Undefined Opcode Exception ESC Opcode Exception Timer 0 Reserved DMA 0/INT5 DMA 1/INT6 INT0 INT1 INT2 INT3 INT4 Asynchronous Serial port 1 Timer 1 Timer 2 Asynchronous Serial port 0 Reserved 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h-1Fh 10h 14h 18h 1Ch 20h 08 1 1 1 1 2-1 28h 2Ch 30h 34h 38h 3Ch 40h 44h 48h 4Ch 50h 0A 0B 0C 0D 0E 0F 10 11 08 08 14 3 4 5 6 7 8 9 9 2-2 2-3 9 */** ** ** */** */** Note * : When the interrupt occurs in the same time, the priority is (1-1 > 1-2) ; (2-1> 2-2 > 2-3) Note **: The interrupt types of these sources are programmable in slave mode. 13.3 Interrupt Request When an interrupt is request, the internal interrupt controller verifies the interrupt is enable (The IF flag is enable, no MSK bit set ) and that there are no higher priority interrupt requests being serviced or pending. If the interrupt is granted , the interrupt controller uses the interrupt type to access a vector from the interrupt vector table. If the external INT is active (level-trigger) to request the interrupt controller service, and the INT pins must hold till the microcontroller enter the interrupt service routine. There is no interrupt-acknowledge output when running in fully nested mode, so it should use PIO pin to simulate the interrupt-acknowledge pin if necessary. 13.4 Interrupt Acknowledge The processor requires the interrupt type as an index into the interrupt table. The internal interrupt can provide the interrupt type or an external controller can provide the interrupt type. The internal interrupt controller provides the interrupt type to processor without external bus cycles generation. When an external interrupt controller is supplying the interrupt type, the processor generates two acknowledge bus cycles, and the interrupt type is written to the AD7-AD0 lines by the external interrupt controller. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 39 RDC ® R8820LV RISC DSP Controller T1 T2 T3 T4 T1 T2 T3 T4 CLKOUTA ADDRESS[19:0] ADDRESS S6 Interrupt TYPE AD15:AD0 ALE BHE INTA0,INTA1 DEN DT/R S2:S0 7 0 7 0 INTR ACK INTR ACK INTERRUPT ACKNOWLEDGE CYCLE (CASECADE OR SLAVE MODE) 13.5 Programming the Registers Software is programmed through the registers ( Master mode: 44h, 42h, 40h, 3Eh, 3Ch, 3Ah, 38h, 36h, 34h, 32h, 30h, 2Eh, 2Ch, 2Ah, 28h, 26h, 24h, 22h; Slave Mode: 3Ah, 38h, 36h, 34h, 32h, 30h, 2Eh, 2Ch, 2Ah, 28h,22h, 20h ) to define the interrupt controller operation. Offset : 44h Reset Value : 000Fh Serial Port 0 Interrupt Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 1 MSK 2 1 0 PR1 PR0 (Master Mode) Bit 15-4 : Reserved Bit 3: MSK, Mask. Set 1: Mask the interrupt source of the asynchronous serial port 0. Set 0: Enable the serial port 0 interrupt. Bit 2-0 : PR2-PR0, Priority. These bits determine the priority of the serial port relative to the other interrupt signals. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 40 RDC ® R8820LV RISC DSP Controller The priority selection: PR2, PR1, PR0 -- Priority 0 , 0 , 0 -- 0 0 , 0 , 1 -- 1 0 , 1 , 0 -- 2 0 , 1 , 1 -- 3 1 , 0 , 0 -- 4 1 , 0 , 1 -- 5 1 , 1 , 0 -- 6 1 , 1 , 1 -- 7 ( High) ( Low ) Offset : 42h Reset Value : 000Fh Serial Port 1 Interrupt Control Register 15 14 12 11 9 8 6 5 3 1 MSK 2 0 PR1 PR0 (Master Mode) Bit 15-4 : Reserved Bit 3: MSK, Mask. Set 1: Mask the interrupt source of the asynchronous serial port 1. Set 0: Enable the serial port 1 interrupt. Bit 2-0 : PR2-PR0, Priority. These bits determine the priority of the serial port relative to the other interrupt signals. The priority selection: PR2, PR1, PR0 -- Priority 0 , 0 , 0 -- 0 0 , 0 , 1 -- 1 0 , 1 , 0 -- 2 0 , 1 , 1 -- 3 1 , 0 , 0 -- 4 1 , 0 , 1 -- 5 1 , 1 , 0 -- 6 1 , 1 , 1 -- 7 ( High) ( Low ) Rev:1.0 RDC Semiconductor Co. Subject to change without notice 41 RDC ® R8820LV RISC DSP Controller Offset : 40h Reset Value : 000Fh INT4 Control Register 15 14 12 11 9 8 6 5 LTM 3 2 0 MSK PR2 PR0 (Master Mode) Bit 15- 8, bit 6-5 : Reserved Bit 7: ETM, Edge trigger enable. When this bit set to 1 and Bit 4 set to 0, interrupt is triggered by low go high edge. The low go high edge will be latched (one level) till this interrupt is been serviced. Bit 4: LTM, Level-Triggered Mode. Set 1: Interrupt is triggered by high active level Set 0 : Interrupt is triggered by low go high edge. Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the INT4 Set 0: Enable the INT4 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of 44h Offset : 3Eh Reset Value : 000Fh INT3 Control Register 15 14 13 12 11 10 9 Reserved 8 7 6 ETM 5 4 3 2 1 0 LTM MSK PR2 PR1 PR0 (Master Mode) Bit 15- 8, bit 6- 5 : Reserved Bit 7: ETM, Edge trigger enable. When this bit set to 1 and Bit 4 set to 0, interrupt is triggered by low go high edge. The low go high edge will be latched (one level) till this interrupt is been serviced. Bit 4: LTM, Level-Triggered Mode. Set 1: Interrupt is triggered by high active level Set 0 : Interrupt is triggered by low go high edge. Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the INT3 Set 0: Enable the INT3 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of 44h Rev:1.0 RDC Semiconductor Co. Subject to change without notice 42 RDC ® R8820LV RISC DSP Controller Offset : 3Ch Reset Value : 000Fh INT2 Control Register 15 14 13 12 11 10 9 8 Reserved 7 6 5 ETM 4 3 2 1 0 LTM MSK PR2 PR1 PR0 (Master Mode) Bit 15- 8, bit 6-5 : Reserved Bit 7: ETM, Edge trigger enable. When this bit set to 1 and Bit 4 set to 0, interrupt is triggered by low go high edge. The low go high edge will be latched (one level) till this interrupt is been serviced. Bit 4: LTM, Level-Triggered Mode. Set 1: Interrupt is triggered by high active level Set 0 : Interrupt is triggered by low go high edge. Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the INT2 Set 0: Enable the INT2 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Offset : 3Ah Reset Value : 000Fh INT1 Control Register 15 14 13 12 11 10 9 8 Reserved 7 6 ETM SFNM 5 4 3 2 1 0 C LTM MSK PR2 PR1 PR0 (Master Mode) Bit 15-8 : Reserved Bit 7: ETM, Edge trigger enable. When this bit set to 1 and Bit 4 set to 0, interrupt is triggered by low go high edge. The low go high edge will be latched (one level) till this interrupt is been serviced. Bit 6: SFNM, Special Fully Nested Mode. Set 1: Enable the special fully nested mode of INT1 Bit 5: C, Cascade Mode. Set this bit to 1 to enable the cascade mode for INT1 or INT0. Bit 4: LTM, Level-Triggered Mode. Set 1: Interrupt is triggered by high active level Set 0 : Interrupt is triggered by low go high edge. Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the INT1 Set 0: Enable the INT1 interrupt. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 43 RDC ® R8820LV RISC DSP Controller Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h (Slave Mode) , This register is for timer 2 interrupt control, reset value is 0000h Bit 15- 4 : Reserved Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the Timer 2 Set 0: Enable the Timer 2 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Offset : 38h Reset Value : 000Fh INT0 Control Register 15 14 13 12 11 10 9 8 Reserved 7 6 ETM SFNM 5 4 3 2 1 0 C LTM MSK PR2 PR1 PR0 (Master Mode) Bit 15-8 : Reserved Bit 7: ETM, Edge trigger enable. When this bit set to 1 and Bit 4 set to 0, interrupt is triggered by low go high edge. The low go high edge will be latched (one level) till this interrupt is been serviced. Bit 6: SFNM, Special Fully Nested Mode. Set 1: Enable the special fully nested mode of INT0. Bit 5: C, Cascade Mode. Set this bit to 1 to enable the cascade mode for INT1 or INT0. Bit 4: LTM, Level-Triggered Mode. Set 1: Interrupt is triggered by high active level Set 0 : Interrupt is triggered by low go high edge. Bit 3 : MSK, Mask. Set 1: Mask the interrupt source of the INT0 Set 0: Enable the INT0 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h (Slave Mode),For Timer 1 interrupt control register, reset value is 0000h Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the timer 1 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 44 RDC ® R8820LV RISC DSP Controller Set 0: Enable the timer 1 interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Offset : 36h Reset Value : 000Fh DMA 1/INT6 Interrupt Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 MSK PR2 PR1 PR0 (Master Mode) Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the DMA 1 controller Set 0: Enable the DMA 1 controller interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h (Slave Mode), reset value is 0000h Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the DMA 1 controller Set 0: Enable the DMA 1 controller interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Offset : 34h Reset Value : 000Fh DMA 0/INT5 Interrupt Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 MSK PR2 PR1 PR0 (Master Mode) Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the DMA 0 controller Set 0: Enable the DMA 0 controller interrupt. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 45 RDC ® R8820LV RISC DSP Controller Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h (Slave Mode), reset value is 0000h Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the DMA 0 controller Set 0: Enable the DMA 1 controller interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Offset : 32h Reset Value : 000Fh Timer Interrupt Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 MSK PR2 PR1 PR0 (Master Mode) Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the timer controller Set 0: Enable the timer controller interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h (Slave Mode), reset value is 0000h Bit 15-4 : Reserved Bit 3: MSK , Mask. Set 1: Mask the interrupt source of the timer 0 controller Set 0: Enable the timer 0 controller interrupt. Bit 2-0: PR, Interrupt Priority These bits setting for priority selection is same as bit 2-0 of the register 44h Rev:1.0 RDC Semiconductor Co. Subject to change without notice 46 RDC ® R8820LV RISC DSP Controller Offset : 30h Reset Value : Interrupt Status Register 15 14 13 12 11 10 9 DHLT 8 7 6 5 4 3 Reserved 2 1 0 TMR2 TMR1 TMR0 (Master Mode), Reset value undefine Bit 15 : DHLT, DMA Halt. Set 1: halts any DMA activity. When non-maskable interrupts occur. Set 0: When an IRET instruction is executed. Bit 14-3 : Reserved. Bit 2-0 : TMR2-TMR0, Set 1: indicates the corresponding timer has an interrupt request pending. (Slave Mode), Reset value is 0000h Bit 15 : DHLT, DMA Halt. Set 1: halts any DMA activity. When non-maskable interrupts occur. Set 0: When an IRET instruction is executed. Bit 14-3 : Reserved. Bit 2-0 : TMR2-TMR0, Set 1: indicates the corresponding timer has an interrupt request pending. Offset : 2Eh Reset Value : Interrupt Request Register 15 14 13 12 Reserved 11 10 9 8 7 6 5 4 SP0 SP1 I4 I3 I2 I1 I0 3 2 D1/I6 D0/I5 1 0 Res TMR (Master Mode) The Interrupt Request register is a read-only register. For internal interrupts (SP0, SP1, D1/I6, D0/I5, and TMR), the corresponding bit is set to 1 when the device requests an interrupt. The bit is reset during the internally generated interrupt acknowledge. For INT4-INT0 external interrupts, the corresponding bit (I4-I0) reflects the current value of the external signal. Bit 15-11 : Reserved. Bit 10 : SP0, Serial Port 0 Interrupt Request. Indicates the interrupt state of the serial port 0. Bit 9 : SP1, Serial Port 1 Interrupt Request. Indicates the interrupt state of the serial port 1. Bit 8-4 : I4-I0, Interrupt Requests. Set 1: The corresponding INT pin has an interrupt pending. Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt Request. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 47 RDC ® R8820LV RISC DSP Controller Set 1: The corresponding DMA channel or INT has an interrupt pending. Bit 1: Reserved. Bit 0 : TMR, Timer Interrupt Request. Set 1: The timer control unit has an interrupt pending. Offset : 2Eh Reset Value : 0000h Interrupt Request Register 15 14 13 12 11 10 9 8 7 6 Reserved 5 4 3 2 TMR2 TMR1 D1/I6 D0/I5 1 0 Res TMR0 (Slave Mode) The Interrupt Request register is a read-only register. For internal interrupts (D1/I6, D0/I5, TMR2, TMR1, and TMR0), the corresponding bit is set to 1 when the device requests an interrupt. The bit is reset during the internally generated interrupt acknowledge. Bit 15-6 : Reserved. Bit 5-4 : TMR2/TMR1, Timer2/Timer1 Interrupt Request. Set 1: Indicates the state of any interrupt requests form the associated timer. Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt Request. Set 1: Indicates the corresponding DMA channel or INT has an interrupt pending. Bit 1 : Reserved. Bit 0 : TMR0, Timer 0 Interrupt Request. Set 1: Indicates the state of an interrupt request from Timer 0. Offset : 2Ch Reset Value : 0000h In - Service Register 15 14 13 12 Reserved 11 10 9 8 7 6 5 4 SP0 SP1 I4 I3 I2 I1 I0 3 2 D1/I6 D0/I5 1 0 Res TMR (Master Mode) The bits in the INSERV register are set by the interrupt controller when the interrupt is taken. Each bit in the register is cleared by writing the corresponding interrupt type to the EOI register. Bit 15-11 : Reserved. Bit 10 : SP0, Serial Port 0 Interrupt In-Service. Set 1: the serial port 0 interrupt is currently being serviced. Bit 9 : SP1, Serial Port 1 Interrupt In-Service. Set 1: the serial port 1 interrupt is currently being serviced. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 48 RDC ® R8820LV RISC DSP Controller Bit 8-4 : I4-I0, Interrupt In-Service. Set 1: the corresponding INT interrupt is currently being serviced. Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt In-Service. Set 1: the corresponding DMA channel or INT interrupt is currently being serviced. Bit 1 : Reserved. Bit 0 : TMR, Timer Interrupt In-Service. Set 1: the timer interrupt is currently being serviced. Offset : 2Ch Reset Value : 0000h In - Service Register 15 14 13 12 11 10 9 8 7 6 Reserved 5 4 TMR2 TMR1 3 2 1 0 D1 D0 Res TMR0 (Slave Mode) The bits in the In-Service register are set by the interrupt controller when the interrupt is taken. The in-service bits are cleared by writing to the EOI register. Bit 15-6 : Reserved. Bit 5-4 : TMR2-TMR1, Timer2/Timer1 Interrupt In-Service. Set 1: the corresponding timer interrupt is currently being serviced. Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt In-Service. Set 1: the corresponding DMA Channel or INT Interrupt is currently being serviced. Bit 1 : Reserved. Bit 0 : TMR0, Timer 0 Interrupt In-Service. Set 1: the Timer 0 interrupt is currently being serviced. Offset : 2Ah Reset Value : 0007h Priority Mask Register 15 14 13 12 11 10 9 8 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 0 0 0 2 1 0 PRM2 PRM1 PRM0 (Master Mode) Determining the minimum priority level at which maskable interrupts can generate an interrupt. Bit 15-3 : Reserved. Bit 2-0 : PRM2-PRM0, Priority Field Mask. Determining the minimum priority that is required in order for a maskable interrupt source to generate an interrupt. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 49 RDC ® R8820LV RISC DSP Controller Priority (High) 0 1 2 3 4 5 6 (Low) 7 PR2-PR0 000 001 010 011 100 101 110 111 (Slave Mode) Determining the minimum priority level at which maskable interrupts can generate an interrupt. Bit 15-3 : Reserved. Bit 2-0 : PRM2-PRM0, Priority Field Mask. Determining the minimum priority that is required in order for a maskable interrupt source to generate an interrupt. Priority PR2-PR0 (High) 0 000 1 001 2 010 3 011 4 100 5 101 6 110 (Low) 7 111 Offset : 28h Reset Value : 07FDh Interrupt Mask Register 15 14 13 12 Reserved 11 10 9 8 7 6 5 4 SP0 SP1 I4 I3 I2 I1 I0 3 2 D1/I6 D0/I5 1 0 Res TMR (Master Mode) Bit 15-11 : Reserved. Bit 10 : SP0, Serial Port 0 Interrupt Mask. The state of the mask bit of the asynchronous serial port 0 interrupt. Bit 9 : SP1, Serial Port 1 Interrupt Mask. The state of the mask bit of the asynchronous serial port 1 interrupt. Bit 8-4 : I4-I0, Interrupt Masks. Indicates the state of the mask bit of the corresponding interrupt. Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt Masks. Indicates the state of the mask bit of the corresponding DMA Channel or INT interrupt. Bit 1: Reserved. Bit 0 : TMR, Timer Interrupt Mask. The state of the mask bit of the timer control unit . Rev:1.0 RDC Semiconductor Co. Subject to change without notice 50 RDC ® R8820LV RISC DSP Controller Offset : 28h Reset Value : 003Dh Interrupt Request Register 15 14 13 12 11 10 9 8 7 6 Reserved 5 4 3 2 TMR2 TMR1 D1/I6 D0/I5 1 0 Res TMR0 (Slave Mode) Bit 15-6 : Reserved. Bit 5-4 : TMR2-TMR1, Timer 2/Timer1 Interrupt Mask. The state of the mask bit of the Timer Interrupt Control register. Set 1: Timer2 or Time1 has its interrupt requests masked Bit 3-2 : D1/I6-D0/I5, DMA Channel or INT Interrupt Mask. Indicating the state of the mask bits of the corresponding DMA or INT6/INT5 control register. Bit 1 : Reserved. Bit 0 : TMR0, Timer 0 Interrupt Mask. The state of the mask bit of the Timer Interrupt Control Register Offset : 26h Reset Value : Poll Status Register 15 14 13 12 11 IREQ 10 9 8 7 6 5 4 3 Reserved 2 1 0 S4 - S0 (Master Mode) The Poll Status (POLLST) register mirrors the current state of the Poll register. the POLLST register can be read without affecting the current interrupt request. Bit 15 : IREQ, Interrupt Request. Set 1: if an interrupt is pending. The S4-S0 field contains valid data. Bit 14-5 : Reserved. Bit 4-0 : S4-S0, Poll Status. Indicates the interrupt type of the highest priority pending interrupt. Offset : 24h Reset Value : Poll Register 15 14 13 IREQ 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 S4 - S0 (Master Mode) When the Poll register is read, the current interrupt is acknowledged and the next interrupt takes its place in the Poll register. Bit 15 : IREQ, Interrupt Request. Set 1: if an interrupt is pending. The S4-S0 field contains valid data. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 51 RDC ® R8820LV RISC DSP Controller Bit 14-5 : Reserved. Bit 4-0 : S4-S0, Poll Status. Indicates the interrupt type of the highest priority pending interrupt. Offset : 22h Reset Value : End - Of - Interrupt 14 13 12 11 10 9 8 7 6 5 4 3 NSPEC 15 2 1 0 S4 - S0 (Master Mode) Bit 15 : NSPEC, Non-Specific EOI. Set 1: indicates non-specific EOI. Set 0: indicates the specific EOI interrupt type in S4-S0. Bit 14-5 : Reserved. Bit 4-0: S4-S0, Source EOI Type. Specifies the EOI type of the interrupt that is currently being processed. Offset : 22h Reset Value : 0000h End - Of - Interrupt 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 L2 L1 L0 (Slave Mode) Bit 15-3 : Reserved. Bit 2-0 : L2-L0, Interrupt Type. Encoded value indicating the priority of the IS(interrupt service) bit to reset. Writes to these bits cause an EOI to be issued for the interrupt type in slave mode. Offset : 20h Reset Value : Interrupt Vector Register 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 7 6 5 4 3 T4 - T0 2 1 0 0 0 0 (Slave Mode) Bit 15-8 : Reserved Bit 7-3 : T4-T0, Interrupt Type. The following interrupt type of slave mode can be programmed. Timer 2 interrupt controller : (T4,T3,T2,T1,T0, 1, 0, 1)b Timer 1 interrupt controller : (T4,T3,T2,T1,T0, 1, 0, 0)b DMA 1 interrupt controller : (T4,T3,T2,T1,T0, 0, 1, 1)b Rev:1.0 RDC Semiconductor Co. Subject to change without notice 52 RDC ® R8820LV RISC DSP Controller DMA 0 interrupt controller : (T4,T3,T2,T1,T0, 0, 1, 0)b Timer 0 interrupt controller : (T4,T3,T2,T1,T0, 0, 0, 0)b Bit 2-0 :Reserved Rev:1.0 RDC Semiconductor Co. Subject to change without notice 53 RDC ® R8820LV RISC DSP Controller 14. DMA Unit The DMA controller provides the data transfer between the memory and peripherals without the intervention of the CPU. There are two DMA channels in the DMA unit. Each channel can accept DMA request from one of three sources: external pin (DRQ0 for channel 0 or DRQ1 for channel 1) or serial port (port 0 or port 1) or Timer 2 overflow. The data transfer from source to destination can be memory to memory ,or memory to I/O, or I/O to I/O, or I/O to memory. Either bytes or words can be transferred to or from even or odd addresses and two bus cycles are necessary (read from source and write to destination) for each data transfer. Adder Control Logic 20-bit Adder/Subtractor CAH.4-Channel 0 TDRQ DAH.4-Channel 1 20 bit Timer 2 Request C8h-Transfer Counter Channel 0 C2h,C0h-Source Address Channel 0 C6h,C4h-Destination Address Channel 0 D8h-Transfer Counter Channel 1 DMA Control Logic DRQ0 Request Arbitration Logic DRQ1 Serial Port0 Serial Port1 D2h,D0h-Source Address Channel 1 Interrupt Request D6h,D4h-Destination Address Channel 1 CAh.8-Channel 0 INT CAh.8-Channel 1 Channel Control Register0,CAh 20 bit Channel Control Register1,DAh 16 bit Internal Address/Data Bus DMA Unit Block 14.1 DMA Operation Every DMA transfer consists of two bus cycles (figure of Typical DMA Transfer) and the two bus cycles can not be separated by a bus hold request, a refresh request or another DMA request. The registers ( CAh, C8h, C6h, C4h, C2h, C0h, DAh, D8h, D6h, D4h, D2h, D0h) are used to configure and operate the two DMA channels. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 54 RDC ® R8820LV RISC DSP Controller T1 T2 T3 T4 T1 T2 T3 T4 CLKOUTA ALE A19-A0 Address AD15-AD0 Address Data Address Data Address RD WR Typical DMA Trarsfer Offset : CAh (DMA0) Reset Value : FFF9h DMA Control Registers 15 14 13 12 11 10 DM/IO DDEC DINC SM/IO SDEC SINC 9 8 TC INT 7 6 SYN1 SYN0 5 P 4 3 TDRQ Res 2 1 0 CHG ST B/W The definition of Bits 15-0 for DMA0 are same as the Bits 15-0 of register DAh for DMA1. Offset : C8h (DMA0) Reset Value : DMA Transfer Count Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0: TC15-TC0, DMA 0 transfer Count. The value of this register is decremented by 1 after each transfer. Offset : C6h (DMA0) Reset Value : DMA Destination Address High Register 15 14 13 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 DDA19 - DDA16 Bit 15-4: Reserved Rev:1.0 RDC Semiconductor Co. Subject to change without notice 55 RDC ® R8820LV RISC DSP Controller Bit 3-0: DDA19-DDA16, High DMA 0 Destination Address. These bits are map to A19- A16 during a DMA transfer when the destination address is in memory space or I/O space. If the destination address is in I/O space (64Kbytes), these bits must be programmed to 0000b. Offset : C4h (DMA0) Reset Value : DMA Destination Address Low Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DDA15 - DDA0 Bit 15-0: DDA15-DDA0, Low DMA 0 Destination Address. These bits are mapped to A15- A0 during a DMA transfer. The value of (DDA19-DDA0)b will increment or decrement by 2 after each DMA transfer. Offset : C2h (DMA0) Reset Value : DMA Source Address High Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DSA19 - DSA16 Bit 15-4: Reserved Bit 3-0: DSA19-DSA16, High DMA 0 Source Address. These bits are mapped to A19- A16 during a DMA transfer when the source address is in memory space or I/O space. If the source address is in I/O space (64Kbytes), these bits must be programmed to 0000b. Offset : C0h (DMA0) Reset Value : DMA Source Address Low Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DSA15 - DSA0 Bit 15-0: DSA15-DSA0, Low DMA 0 Source Address. These bits are mapped to A15- A0 during a DMA transfer. The value of (DSA19-DSA0)b will increment or decrement by 2 after each DMA transfer. Offset : DAh (DMA1) Reset Value : FFF9h DMA Control Registers 15 14 13 12 11 10 DM/IO DDEC DINC SM/IO SDEC SINC 9 8 TC INT 7 6 SYN1 SYN0 5 P 4 3 TDRQ Res 2 1 0 CHG ST B/W Rev:1.0 RDC Semiconductor Co. Subject to change without notice 56 RDC ® R8820LV RISC DSP Controller Bit 15: DM / IO , Destination Address Space Select. Set 1: The destination address is in memory space. Set 0: The destination address is in I/O space. Bit 14: DDEC, Destination Decrement. Set 1: The destination address is automatically decrement after each transfer. The B /W (bit 0) bit determines the decrement value which is by 1 or 2 When both DDEC and DINC bits are set to 1, the address remains constant Set 0 : Disable the decrement function. Bit 13: DINC, Destination Increment. Set 1: The destination address is automatically increment after each transfer. The B /W (bit 0) bit determines the increment value which is by 1 or 2 Set 0 : Disable the decrement function. Bit 12: SM/ IO , Source Address Space Select. Set 1: The Source address is in memory space. Set 0: The Source address is in I/O space Bit 11: SDEC, Source Decrement. Set 1: The Source address is automatically decrement after each transfer. The B /W (bit 0) bit determines the decrement value which is by 1 or 2 When both SDEC and SINC bits are set to 1, the address remains constant Set 0 : Disable the decrement function. Bit 10: SINC, Source Increment. Set 1: The Source address is automatically increment after each transfer. The B /W (bit 0) bit determines the increment value which is by 1 or 2 Set 0 : Disable the decrement function Bit 9 : TC, Terminal Count. Set 1: The synchronized DMA transfer is terminated when the DMA transfer count register reaches 0. Set 0: The synchronized DMA transfer is terminated when the DMA transfer count register reaches 0. Unsynchronized DMA transfer is always terminated when the DMA transfer count register reaches 0, regardless the setting of this bit. Bit 8 : INT, Interrupt. Set 1: DMA unit generates an interrupt request when complete the transfer count . The TC bit must set to 1 to generate an interrupt. Bit 7-6: SYN1-SYN0, Synchronization Type Selection. SYN1 , SYN0 -- Synchronization Type 0 , 0 -- Unsynchronized 0 , 1 -- Source synchronized Rev:1.0 RDC Semiconductor Co. Subject to change without notice 57 RDC ® R8820LV RISC DSP Controller 1 , 0 -- Destination synchronized 1 , 1 -- Reserved Bit 5: P , Priority. Set 1: It selects high priority for this channel when both DMA 0 and DMA 1 are transfer in same time. Bit 4: TDRQ, Timer Enable/Disable Request Set 1: Enable the DMA requests from timer 2. Set 0: Disable the DMA requests from timer 2. Bit 3: Reserved Bit 2: CHG, Changed Start Bit. This bit must set to 1 when will modify the ST bit. Bit 1: ST, Start/Stop DMA channel. Set 1: Start the DMA channel Set 0: Stop the DMA channel Bit 0 : B /W, Byte/Word Select. Set 1: The address is incremented or decremented by 2 after each transfer. Set 0 :The address is incremented or decremented by 1 after each transfer. Offset : D8h (DMA1) Reset Value : DMA Transfer Count Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0: TC15-TC0, DMA 1 transfer Count. The value of this register is decremented by 1 after each transfer. Offset : D6h (DMA1) Reset Value : DMA Destination Address High Register 15 14 13 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 DDA19 - DDA16 Bit 15-4: Reserved Bit 3-0: DDA19-DDA16, High DMA 1 Destination Address. These bits are map to A19- A16 during a DMA transfer when the destination address is in memory space or I/O space. If the destination address is in I/O space (64Kbytes), these bits must be programmed to 0000b. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 58 RDC ® R8820LV RISC DSP Controller Offset : D4h (DMA1) Reset Value : DMA Destination Address Low Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DDA15 - DDA0 Bit 15-0: DDA15-DDA0, Low DMA 1 Destination Address. These bits are mapped to A15- A0 during a DMA transfer. The value of (DDA19-DDA0)b will increment or decrement by 2 after each DMA transfer. Offset : D2h (DMA1) Reset Value : DMA Source Address High Register 15 14 13 12 11 10 9 8 7 6 5 4 3 Reserved 2 1 0 DSA19 - DSA16 Bit 15-4: Reserved Bit 3-0: DSA19-DSA16, High DMA 1 Source Address. These bits are mapped to A19- A16 during a DMA transfer when the source address is in memory space or I/O space. If the source address is in I/O space (64Kbytes), these bits must be programmed to 0000b. Offset : D0h (DMA1) Reset Value : DMA Source Address Low Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DSA15 - DSA0 Bit 15-0: DSA15-DSA0, Low DMA 1 Source Address. These bits are map to A15- A0 during a DMA transfer. The value of (DSA19-DSA0)b will increment or decrement by 2 after each DMA transfer. 14.2 External Requests External DMA requests are asserted on the DRQ pins. The DRQ pins are sampled on the falling edge of CLKOUTA. It takes a minimum of four clocks before the DMA cycle is initiated by the Bus Interface. The DMA request is cleared four clocks before the end of the DMA cycle. And no DMA acknowledge is provided, since the chip-selects (MCSx, PCSx) can be programmed to be active for a given block of memory or I/O space, and the DMA source and destination address registers can be programmed to point to the same given block. DMA transfer can be either source or destination synchronized, and it can also be unsynchronized. The Source-Synchronized Transfer figure shows the typical source-synchronized transfer which provides the source device at least three clock cycles from the time it is acknowledged to deassert its DRQ line. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 59 RDC ® R8820LV RISC DSP Controller Fetch Cycle T1 T2 T3 Fetch Cycle T4 T1 T2 T3 T4 CLKOUTA DRQ(Case1) DRQ(Case2) NOTES: Case1 : Current source synchronized transfer will not be immediately followed by another DMA transfer. Case2 : Current source synchronized transfer will be immediately followed by antoher DMA transfer. Source-Synchronized Transfers The Destination-Synchronized Transfer figure shows the typical destination-synchronized transfer which differs from a sourcesynchronized transfer in that two idle states are added to the end of the deposit cycle. The two idle states extend the DMA cycle to allow the destination device to deassert its DRQ pin four clocks before the end of the cycle. If the two idle states were not inserted, the destination device would not have time to deassert its DRQ signal. Fetch Cycle T1 T2 T3 Fetch Cycle T4 T1 T2 T3 T4 TI TI CLKOUTA DRQ(Case1) DRQ(Case2) NETES: Case1 : Current destination synchronized transfer will not be immediately followed by another DMA transfer. Case2 : Current destination synchronized transfer will be immediately followed by another DMA transfer. Destination-Synchronized Transfers Rev:1.0 RDC Semiconductor Co. Subject to change without notice 60 RDC ® R8820LV RISC DSP Controller 14.3 Serial Port/DMA Transfer The serial port data can be DMA transfer to or from memory( or IO) space. And the B /W bit of DMA control Register must be set 1 for byte transfer. The map address of Transmit Data Register is written to the DMA Destination Address Register and the memory (or I/O) address is written to the DMA Source Address Register, when transmit data. The map address of Receive Data Register is written to the DMA Source Address Register and the memory (or I/O) address is written to the DMA Destination Address Register, when receive data. The software is programmed through the Serial Port Control Register to perform the serial port/ DMA transfer. When a DMA channel is in use by a serial port, the corresponding external DMA request signal is deactivated. For DMA to the serial port, the DMA channel should be configured as destination synchronized. For DMA from the serial port, the DMA channel should be configured as source synchronized. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 61 RDC ® R8820LV RISC DSP Controller 15. Timer Control Unit TMRIN1 TMRIN0 Microprocessor Clock 50h,Timer 0 Count Register TMROUT1 52h,54h,Timer0 Maxcount Compare Register Counter Element & Control Logic 58h,Timer 1 Compare Register 5Ah,5Ch,Timer 1 Maxcount Compare Register 60h,Timer 2 count Register TMROUT2 (Timer2) (Timer0,1,2) DMA Request Interrupt Request 62h,Timer 2 Count Register 16 bit 56h,Timer 0 Control Register 16 bit 5Eh,Timer 1 Control Register 66h,Timer 2 Control Register 16 bit Internal Address/Data Bus Timer / Counter Unit Block There are three 16-bit programmable timers in the R8820LV. The timer operation is independent of the CPU. The three timers can be programmed as a timer element or as a counter element. Timers 0 and 1 are each connect to two external pins (TMRIN0, TMROUT0, TMRIN1, TMROUT1) which can be used to count or time external events, or they can be used to generate a variable-duty-cycle waveforms. Timer 2 is not connected any external pins. It can be used as a prescale to timer 0 and timer 1 or as a DMA request source. Offset : 56h Reset Value : 0000h Timer 0 Mode / Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 EN INH INT RIU 0 0 0 0 0 0 MC RTG P EXT 1 0 ALT CONT These bits definition for timer 0 are same as the bits of register 5Eh for timer 1. Offset : 50h Reset Value : Timer 0 Count Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 62 RDC ® R8820LV RISC DSP Controller Bit 15 – 0: TC15-TC0, Timer 0 Count Value. This register contains the current count of timer 0. The count is incremented by one every four internal processor clocks or by prescaled the timer 2, or by one every four external clock which is configured the external clock select bit to refer the TMRIN1 signal. Offset : 52h Reset Value : Timer 0 Maxcount Compare A Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0 : TC15 – TC0, Timer 0 Compare A Value. Offset : 54h Reset Value : Timer 0 Maxcount Compare B Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0 : TC15 – TC0, Timer 0 Compare B Value. Offset : 5Eh Reset Value : 0000h Timer 1 Mode / Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 EN INH INT RIU 0 0 0 0 0 0 MC RTG P EXT 1 0 ALT CONT Bit 15: EN, Enable Bit. Set 1: The timer 1 is enable. Set 0: The timer 1 is inhibited from counting. The INH bit must be set 1 during writing the EN bit, and the INH bit and EN bit must be in the same write. Bit 14: INH , Inhibit Bit. This bit is allows selective updating the EN bit. The INH bit must be set 1 during writing the EN bit, and both the INH bit and EN bit must be in the same write. This bit is not stored and is always read as 0. Bit 13: INT, Interrupt Bit. Set 1: A interrupt request is generated when the count register equals a maximum count. If the timer is configured in dual max-count mode, an interrupt is generated each time the count reaches max-count A or max-count B Set 0: Timer 1 will not issue interrupt request. Bit 12: RIU, Register in Use Bit. Set 1: The Maxcount Compare B register of timer 1 is being used Rev:1.0 RDC Semiconductor Co. Subject to change without notice 63 RDC ® R8820LV RISC DSP Controller Set 0: The Maxcount Compare A register of timer 1 is being used Bit 11-6 : Reserved. Bit 5: MC, Maximum Count Bit. When the timer reaches its maximum count, the MC bit will set to 1 by H/W. In dual maxcount mode, this bit is set each time either Maxcount Compare A or Maxcount Compare B register is reached. This bit is set regardless of the EN bit (66h.15). Bit 4: RTG, Re-trigger Bit. This bit define the control function by the input signal of TMRIN1 pin. When EXT=1 (5Eh.2), this bit is ignored. Set 1: Timer1 Count Register (58h) counts internal events; Reset the counting on every TMRIN1 input signal from low go high (rising edge trigger). Set 0: Low input holds the timer 1 Count Register (58h) value; High input enables the counting which counts internal events. The definition of setting the (EXT , RTG ) ( 0 , 0 ) – Timer1 counts the internal events. if the TMRIN1 pin remains high. ( 0 , 1 ) -- Timer1 counts the internal events; count register reset on every rising transition on the TMRIN1 pin ( 1 , x ) -- TMRIN1 pin input acts as clock source and timer1 count register increase one every four external clock. Bit 3: P, Prescaler Bit. This bit and EXT(5Eh.2) define the timer 1 clock source. The definition of setting the (EXT , P ) ( 0 , 0 ) – Timer1 Count Register increase one every four internal processor clock. ( 0 , 1 ) – Timer1 count register increase one which prescal by timer 2. ( 1 , x ) -- TMRIN1 pin input acts as clock source and Timer1 Count Register increase one every four external clock. Bit 2: EXT, External Clock Bit. Set 1: Timer 1 clock source from external Set 0: Timer 1 clock source from internal Bit 1 : ALT, Alternate Compare Bit. This bit controls whether the timer runs in single or dual maximum count mode. Set 1: Specify dual maximum count mode. In this mode the timer counts to Maxcount Compare A, then resets the count register to 0. Then the timer counts to Maxcount Compare B, then resets the count register to 0 again, and starts over with Maxcount Compare A. Set 0: Specify single maximum count mode. In this mode the timer will count to the valve contained in Maxcount Compare A and reset to 0, and then the timer counts to Maxcount Compare A again. Maxcount Compare B is not used in this mode. Bit 0: CONT, Continuous Mode Bit. Set 1: The timer to run continuously. Set 0: The timer will halt after each counting to the maximum count and the EN bit will be cleared. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 64 RDC ® R8820LV RISC DSP Controller Offset : 58h Reset Value : Timer 1 Count Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15 – 0: TC15-TC0, Timer 1 Count Value. This register contains the current count of timer 1. The count is incremented by one every four internal processor clocks or by prescaled the timer 2, or by one every four external clock which is configured the external clock select bit to refer the TMRIN1 signal. Offset : 5Ah Reset Value : Timer 1 Maxcount Compare A Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 3Bit 15-0 : TC15 – TC0, Timer 1 Compare A Value. Offset : 5Ch Reset Value : Timer 1 Maxcount Compare B Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0 : TC15 – TC0, Timer 1 Compare B Value. Offset : 66h Reset Value : 0000h Timer 2 Mode / Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EN INH INT 0 0 0 0 0 0 0 MC 0 0 0 0 CONT Bit 15: EN, Enable Bit. Set 1: The timer 2 is enable. Set 0: The timer 2 is inhibited from counting. The INH bit must be set 1 during writing the EN bit, and the INH bit and EN bit must be in the same write. Bit 14: INH , Inhibit Bit. This bit is allows selective updating the EN bit. The INH bit must be set 1 during writing the EN bit, and both the INH bit and EN bit must be in the same write. This bit is not stored and is always read as 0. Bit 13: INT, Interrupt Bit. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 65 RDC ® R8820LV RISC DSP Controller Set 1: A interrupt request is generated when the count register equals a maximum count. Set 0: Timer 2 will not issue interrupt request. Bit 12-6 : Reserved. Bit 5: MC, Maximum Count Bit. When the timer reaches its maximum count, the MC bit will set to 1 by H/W. This bit is set regardless of the EN bit (66h.15). Bit 4-1: Reserved. Bit 0: COUNT, Continuous Mode Bit. Set 1: Timer is continuously running when timer reaches the maximum count. Set 0: The EN bit (66h.15) is cleared and the timer is hold after each timer count reaches the maximum count. Offset : 60h Reset Value : Timer 2 Count Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15 – 0: TC15-TC0, Timer 2 Count Value. This register contains the current count of timer 2. The count is incremented by one every four internal processor clocks. Offset : 62h Reset Value : Timer 2 Maxcount Compare A Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TC15 - TC0 Bit 15-0 : TC15 – TC0, Timer 2 Compare A Value. 15.1 Timer/Counter Unit Output Mode Timers 0 and 1 can use one maximum count value or two maximum count value. Timer 2 can use only one maximum count value. Timer 0 and timer1 can be configured to single or dual Maximum Compare count mode, the TMROUT0 or TMROUT1 signals can be used to generated waveform of various duty cycle. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 66 RDC ® R8820LV RISC DSP Controller Maxcount A Maxcount B Maxcount A Maxcount B Dual Maximum Count Mode Single Maximum Count Mode Maxcount A 1T Maxcount A 1T Maxcount A * 1T:One Microprocessor clock Timer/Counter Unit Output Modes Rev:1.0 RDC Semiconductor Co. Subject to change without notice 67 RDC ® R8820LV RISC DSP Controller 16. Watchdog Timer R8820LV has one independent watchdog timer, which is programmable. The watchdog timer is active after reset and the timeout count with a maximum count value. The keyed sequence ( 3333h, CCCCh ) must be written to the register (E6h) first then writing new configuration to the Watchdog Timer Control Register. It is a single write so every one writing to Watchdog Timer Control Register must follow the rule. To read the Watchdog Timer Control Register, the keyed sequence (5555h, AAAAh) must be written to the register (E6h) first. The current count should be reset before modifying the Watchdog Timer timeout period to ensure that an immediate timeout dose not occur. Offset : E6h Reset Value : C080h 15 14 13 12 ENA WRST RSTFLAG NMIFLAG Watchdog Timer Control Register 11 10 9 8 7 Res 6 5 4 3 2 1 0 COUNT Bit 15: ENA, Enable Watchdog Timer. Set 1 : Enable Watchdog Timer. Set 0 : Disable Watchdog Timer. Bit 14: WRST, Watchdog Reset. Set 1: WDT generates a system reset when WDT timeout count is reached. Set 0 : WDT generates a NMI interrupt when WDT timeout count is reached if the NMIFLAG bit is 0. If the NMIFLAG bit is 1, the WDT will generate a system reset when timeout. Bit 13: RSTFLAG, Reset Flag. When watchdog timer reset event has occurred, hardware will set this bit to 1. This bit will be cleared by any keyed sequence write to this register or external reset. This bit is 0 after an external reset or 1 after watchdog timer reset. Bit 12: NMIFLAG, NMI Flag. After WDT generates a NMI interrupt, this bit will be set to 1 by H/W. This bit will be cleared by any keyed sequence write to this register. Bit 11-8 : Reserved. Bit 7-0 : COUNT, Timeout Count. The COUNT setting determines the duration of the watchdog timer timeout interval. a. The duration equation : Duration = 2 Exponent / Frequency b. The Exponent of the COUNT setting: (Bit 7, Bit 6, Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, Bit 0) = ( Exponent) ( 0 , 0 , 0 , 0, 0 , 0 , 0 , 0 ) = (N/A) ( x , x , x , x, x , x , x , x ) = ( 10 ) (x , x , x , x, x , x , 1 , 0 ) = ( 20 ) (x , x , x , x, x , 1 , 0 , 0 ) = ( 21 ) Rev:1.0 RDC Semiconductor Co. Subject to change without notice 68 RDC ® R8820LV RISC DSP Controller (x , x , x , x, 1 , 0 , 0 , 0 ) = ( 22 ) (x , x , x , 1, 0 , 0 , 0 , 0 ) = ( 23 ) (x , x , 1 , 0, 0 , 0 , 0 , 0 ) = ( 24 ) ( x , 1 , 0 , 0, 0 , 0 , 0 , 0 ) = ( 25 ) ( 1 , 0 , 0 , 0, 0 , 0 , 0 , 0 ) = ( 26 ) c. Watchdog timer Duration reference table: Frequency\Exponent 20 MHz 25 MHz 33 MHz 40 MHz 50 MHz 10 51 us 40 us 30 us 25 us 20.5 us 20 52 ms 41 ms 31 ms 26 ms 21 ms 21 104 ms 83 ms 62 ms 52 ms 41.9 ms 22 209 ms 167 ms 125 ms 104 ms 83.9ms 23 24 419 ms 838 ms 335 ms 671 ms 251 ms 503 ms 209 ms 419 ms 167.8 ms 335.5 ms 25 1.67 s 1.34 s 1.00 s 838 ms 671 ms 26 3.35 s 2.68 s 2.01 s 1.67 s 1.34 s Rev:1.0 RDC Semiconductor Co. Subject to change without notice 69 RDC ® R8820LV RISC DSP Controller 17. Asynchronous Serial Port R8820LV has two asynchronous serial ports, which provide the TXD, RXD pins for the full duplex bi-directional data transfer and with handshaking signals CTS , ENRX , RTS , RTR . The serial ports support : 9-bit, 8-bit or 7-bit data transfer; odd parity, even parity, or no parity; 1 stop bits; Error detection; DMA transfers through the serial port; Multi-drop protocol (9-bit) support; Double buffers for transmit and receive. The receive/transmit clock is based on the microprocessor clock. The serial port can be used in power-saved mode, but the transfer rate must be adjusted to correctly reflect the new internal operating frequency. Software is programmed through the registers ,(80h, 82h, 84h, 86h, 88h – for port 0), ( 10h,12h,14h,16h,18h – for port 1) to configure the asynchronous serial port. Internal Address/Data Bus 16 bit 16 bit Transmit Data Register(84h),(14h) Receive Data Register(86h),(16h) 16 bit 8 bit 8 bit 8 bit TXD Transmit Shift Regoster Transmit Hold Register Receive Buffer 8 bit Interrupt Request RTS ENRX CTS RTR Control Register(80h),(10h) Control Logic Receive Shift Register Status Register(82h),(12h) Baud Rate Divisor Register(88h),(18h) RXD Serial Port Block Diagram 17.1 Serial Port Flow Control The two serial ports provided with two data pins (RXD and TXD) and two flow control signals ( RTS , RTR ). Hardware flow control is enabled when the FC bit in the Serial Port control Register is set. And the flow control signals are configured by software to support several different protocols. 17.1.1 DCE/DTE Protocol The R8820LV can be as a DCE (Data Communication Equipment) or as a DTE ( Data Terminal Equipment). This protocol provides flow control where one serial port is receiving data and other serial port is sending data. To implement the DCE device, the ENRX bit should be set and the RTS bit should be cleared for the associated serial port. To implement the DTE device, the ENRX bit should be cleared and the RTS bit should be set for the associated serial port. The ENRX bit and RTS bit are in the register F2h. The DCE/DTE protocol is asymmetric interface since the DTE device can not signal the DCE device that is ready to receive Rev:1.0 RDC Semiconductor Co. Subject to change without notice 70 RDC ® R8820LV RISC DSP Controller data, and the DCE can not send the request to send signal. ENRX RTS DCE RTS:Request to send CTS:Clear to send RTR:Ready to receive ENRX:Enable receiver request DTE RTR CTS DCE/DTE Protocol Connection The DCE/DTE protocol communication step: a. DTE send data to DCE b. RTS signal is asserted by DTE when data is available. c. The RTS signal is interpreted by the DCE device as a request to enable its receiver. d. The DCE asserts the RTR signal to response that DCE is ready to receive data. 17.1.2 CTS/RTR Protocol The serial port can be programmed as a CTS/RTS protocol by clearing both ENRX bit and RTS bit. This protocol is a symmetric interface, which provides flow control when both ports are sending and receiving data. CTS RTR CTS:Clear to send RTR:Ready to receive RTR CTS CTS/RTR Protocol Connection 17.2 DMA Transfer to/from a serial port function DMA transfers to the serial port function as destination-synchronized DMA transfers. A new transfer is requested when the Transmit Holding Register is empty. When the port is configured for DMA transmits, the corresponding transmit interrupt is disabled regardless of the TXIE bit setting. DMA transfers from the serial port function as source-synchronized DMA transfers. A new transfer is requested when the Receive Buffer contains valid data. When the port is configured for DMA receives, the corresponding receive interrupt is disabled regardless of the RXIE bit setting. The DMA request is generated internally when a DMA channel is being used for serial port transfers. And the DRQ0 or DRQ1 are not active when a serial port DMA transfers. Hardware handshaking may be used in conjunction with serial port DMA transfers. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 71 RDC ® R8820LV RISC DSP Controller 17.3 The Asynchronous Modes description There are 4 modes operation in the asynchronous serial port. Mode1: Mode 1 is the 8-bit asynchronous communications mode. Each frame consists of a start bit, eight data bits and a stop bit. when parity is used, the eighth data bit becomes the parity bit. Mode 2: Mode 2 is used together with Mode 3 for multiprocessor communications over a common serial link. In mode 2, the RX machine will not complete a reception unless the ninth data bit is a one. Any character received with the ninth bit equal to zero is ignored. No flags are set, no interrupts occur and no data is transferred to Receive Data Register. In mode 3, characters are received regardless of the state of the ninth data bit. Mode 3: Mode 3 is the 9-bit asynchronous communications mode. Mode 3 is the same as mode 1 except that a frame contains nine data bits. The ninth data bit becomes the parity bit when the parity feature is enabled. Mode 4: Mode 4 is the 7-bit asynchronous communications mode. Each frame consists of a start bit, seven data bits and a stop bit. Parity bit is not available in mode 4. Offset : 80h Reset Value : 0000h 14 DMA 13 12 11 10 9 RISE BRK TB8 FC 8 7 TXIE RXIE 6 5 4 3 RMODD 15 TMODE Serial Port 0 Contrl Register EVN PE 2 1 0 MODE Bit 15-13: DMA, DMA Control Field. These bits configure the serial port for use with DMA transfers. DMA control bits (Bit 15, bit 14, bit 13)b --- Receive --- Transmit ( 0, 0, 0 ) --- No DMA --- No DMA ( 0, 0, 1 ) --- DMA 0 --- DMA 1 ( 0, 1, 0 ) --- DMA 1 --- DMA 0 ( 0, 1, 1 ) --- N/A --- N/A ( 1, 0, 0 ) --- DMA 0 --- No DMA ( 1, 0, 1 ) --- DMA 1 --- No DMA ( 1, 1, 0 ) --- No DMA --- DMA 0 ( 1, 1, 1 ) --- No DMA --- DMA 1 Bit 12: RSIE, Receive Status Interrupt Enable. An exception occurs during data reception or error detection occur will generate an interrupt. Set 1: Enable the serial port 0 to generate an interrupt request. Bit 11: BRK, Send Break. Set this bit to 1 , the TXD pin always drives low. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 72 RDC ® R8820LV RISC DSP Controller Long Break : The TXD is driven low for grater than (2M+3) bit times; Short break : The TXD is driven low for grater than M bit times; * M= start bit + data bits number + parity bit + stop bit Bit 10 : TB8, Transmit Bit 8. This bit is transmitted as ninth data bit in mode 2 and mode 3. This bit is cleared after every transmission. Bit 9: FC, Flow Control Enable. Set 1: Enable the hardware flow control for serial port 0. Set 0 : Disable the hardware flow control for serial port 0. Bit 8 : TXIE, Transmitter Ready Interrupt Enable. When the Transmit Holding Register is empty ( THRE bit in Status Register is set ),it will have an interrupt occurs. Set 1: Enable the Interrupt. Set 0 : Disable the interrupt. Bit 7: RXIE, Receive Data Ready Interrupt Enable. When the receiver buffer contains valid data ( RDR bit in Status Register is set) , it will generate an interrupt. Set 1: Enable the Interrupt. Set 0 : Disable the interrupt. Bit 6 : TMODE, Transmit Mode. Set 1: Enable the TX machines. Set 1: Disable the TX machines. Bit 5: RMODE, Received Mode. Set 1: Enable the RX machines. Set 1: Disable the RX machines. Bit 4: EVN, Even Parity. This bit is valid only when the PE bit is set. Set 1: the even parity checking is enforced (even number of 1s in frame). Set 0: odd parity checking is enforced (odd number of 1s in frame). Bit 3: PE, Parity Enable. Set 1 : Enable the parity checking. Set 0 : Disable the parity checking. Bit 2-0: MODE, Mode of Operation. ( bit 2, bit 1, bit 0) MODE ( 0 , 0 , 1) Mode 1 ( 0 , 1 , 0) Mode 2 ( 0 , 1 , 1) Mode 3 ( 1 , 0 , 0) Mode 4 Data Bits 7 or 8 9 8 or 9 7 Parity Bits 1 or 0 N/A 1 or 0 N/A Stop Bits 1 1 1 1 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 73 RDC ® R8820LV RISC DSP Controller Offset : 82h Reset Value : Serial Port 0 Status Register 15 14 13 12 11 Reserved 10 9 BRK1 BRK0 8 RB8 7 6 5 RDR THRE FER 4 OER 3 2 1 PER TEMT HS0 0 Res The Serial Port 0 Status Register provides information about the current status of the serial port 0. Bit 15-11: Reserved. Bit 10: BRK1, Long Break Detected. This bit should be reset by software. When a long break is detected, this bit will be set high. Bit 9 : BRK0, Short Break Detected. This bit should be reset by software. When a short break is detected, this bit will be set high Bit 8: RB8,Received Bit 8. This bit should be reset by software. This bit contains the ninth data bit received in mode 2 and mode 3. Bit 7: RDR, Received Data Ready. Read only. The Received Data Register contains valid data, this bit is set high. This bit can only be reset by reading the Serial Port 0 Receive Register. Bit 6: THRE, Transmit Hold Register Empty. Read only. When the Transmit Hold Register is ready to accept data, this bit will be set. This bit will be reset when writing data to the Transmit Hold Register. Bit 5: FER, Framing Error detected. This bit should be reset by software. This bit is set when a framing error is detected. Bit 4: OER, Overrun Error Detected. This bit should be reset by software. This bit is set when an overrun error is detected. Bit 3: PER, Parity Error Detected. This bit should be reset by software. This bit is set when a parity error ( for mode 1 and mode 3) is detected. Bit 2: TEMT, Transmitter Empty. This bit is read only. When the Transmit Shift Register is empty, this bit will be set. Bit 1: HS0, Handshake Signal 0. This bit is read only. This bit reflects the inverted value of the external CTS0 pin. Bit 0 : Reserved. Offset : 84h Reset Value : Serial Port 0 Transmit Register 15 14 13 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 TDATA Bit 15-8: Reserved Rev:1.0 RDC Semiconductor Co. Subject to change without notice 74 RDC ® R8820LV RISC DSP Controller Bit 7-0 : TDATA, Transmit Data. Software writes this register with data to be transmitted on the serial port 0. Offset : 86h Reset Value : Serial Port 0 Receive Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RDATA Reserved Bit 15-8: Reserved Bit 7-0: RDATA, Received DATA. The RDR bit should be read as 1 before read the RDATA register to avoid reading invalid data. Offset : 88h Reset Value : 0000h Serial Port 0 Baud Rate Divisor Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BAVDDIV Bit 15-0: BAUDDIV, Baud Rate Divisor. The general formula for baud rate divisor is Baud Rate = Microprocessor Clock / (16 x BAUDIV) For example, The Microprocessor clock is 22.1184MHz and the BBDIV=5 (Decimal), the baud rate of serial port is 115.2k. Offset : 10h Reset Value : 0000h 14 13 DMA 12 11 10 9 RISE BRK TB8 FC 8 7 TXIE RXIE 6 5 4 3 RMODD 15 TMODE Serial Port 1 Contrl Register EVN PE 2 1 0 MODE These bits definition are same as the bits definition of Register 80h Offset : 12h Reset Value : Serial Port 1 Status Register 15 14 13 Reserved 12 11 10 9 BRK1 BRK0 8 RB8 7 6 5 4 RDR THRE FER OER 3 2 1 PER TEMT HS0 0 Res These bits definition are same as the bits definition of Register 82h Rev:1.0 RDC Semiconductor Co. Subject to change without notice 75 RDC ® R8820LV RISC DSP Controller Offset : 14h Reset Value : Serial Port 1 Transmit Register 15 14 13 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 TDATA These bits definition are same as the bits definition of Register 84h Offset : 16h Reset Value : Serial Port 1 Receive Register 15 14 13 12 11 10 9 8 7 6 5 4 Reserved 3 2 1 0 RDATA These bits definition are same as the bits definition of Register 86h Offset : 18h Reset Value : 0000h Serial Port 1 Baud Rate Divisor Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BAVDDIV These bits definition are same as the bits definition of Register 88h Rev:1.0 RDC Semiconductor Co. Subject to change without notice 76 RDC ® R8820LV RISC DSP Controller 18. PIO Unit R8820LV provides 32 programmable I/O signals, which are multi-function pins with others normal function signals. Software is programmed through the registers ( 7Ah, 78h, 76h, 74h, 72h, 70h) to configure the multi-function pins for PIO or normal function. For internal pull-up VCC PIO PIO Mode Direction Normal Function Pin D PIO Data In/Out Q VCC Write PDATA Q Read PDATA D OE Microprocessor Clock For internal pull-down Normal Data In "0":un-normal function PIO pin Operation Diagram 18.1 PIO multi-function Pin list table PIO No. 0 1 2 Pin No. 72 73 59 Multi Function TMRIN1 TMROUT1 PCS6 /A2 Reset status/PIO internal resister Input with 10k pull-up Input with 10k pull-down Input with 10k pull-up 3 60 PCS5 /A1 4 5 48 49 6 7 8 9 10 11 12 13 14 46 22 20 19 74 75 77 76 50 DT/ R DEN SRDY A17 A18 A19 TMROUT0 TMRIN0 DRQ0/INT5 DRQ1/INT6 MCS0 15 51 MCS1 Input with 10k pull-up 16 66 PCS0 Input with 10k pull-up 17 65 PCS1 Input with 10k pull-up Input with 10k pull-up Normal operation/ Input with 10k pull-up Normal operation/ Input with 10k pull-up Normal operation/ Input with 10k pull-down Normal operation/ Input with 10k pull-up Normal operation/ Input with 10k pull-up Normal operation/ Input with 10k pull-up Input with 10k pull-down Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Rev:1.0 RDC Semiconductor Co. Subject to change without notice 77 RDC ® R8820LV RISC DSP Controller 18 63 PCS2 / CTS1 / ENRX1 Input with 10k pull-up 19 62 PCS3 / RTS1 / RTR 1 Input with 10k pull-up 20 3 RTS0 / RTR 0 Input with 10k pull-up 21 100 Input with 10k pull-up 22 23 24 2 1 68 CTS0 / ENRX0 TXD0 RXD0 MCS2 25 69 MCS3 / RFSH Input with 10k pull-up 26 97 Input with 10k pull-up 27 28 29 98 99 96 30 31 52 54 UZI TXD1 RXD1 S6/ CLKDIV INT4 INT2 Input with 10k pull-down Input with 10k pull-down Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Input with 10k pull-up Offset : 7Ah Reset Value : PIO Data 1 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PDATA (31 - 16) Bit 15- 0 : PDATA31-PDATA16, PIO Data Bits. These bits PDATA31- PDATA16 map to the PIO31 –PIO16 which indicate the driven level when the PIO pin as an output or reflects the external level when the PIO pin as an input . Offset : 78h Reset Value : FFFFh PIO Direction 1 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PDIR (31 - 16) Bit 15-0 : PDIR 31- PDIR16, PIO Direction Register. Set 1: Configure the PIO pin as an input. Set 0: Configure the PIO pin as an output or as normal pin function. Offset : 76h Reset Value : 0000h PIO Mode 1 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PMODE (31 - 16) Bit 15-0: PMODE31-PMODE16, PIO Mode Bit. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 78 RDC ® R8820LV RISC DSP Controller The definition of PIO pins are configured by the combination of PIO Mode and PIO Direction. And the PIO pin is programmed individual. The definition (PIO Mode, PIO Direction) for PIO pin function: ( 0 , 0 ) – Normal operation , ( 0 , 1 ) – PIO input with pull-up/pull-down ( 1 , 0 ) – PIO output , ( 1 , 1 ) -- PIO input without pull-up/pull-down Offset : 74h Reset Value : PIO Data 0 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PDATA (15 - 0) Bit 15-0 : PDATA15- PDATA0 : PIO Data Bus. These bits PDATA15- PDATA0 map to the PIO15 –PIO0 which indicate the driven level when the PIO pin as an output or reflects the external level when the PIO pin as an input. Offset : 72h Reset Value : FFFFh PIO Direction 0 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PDIR (15 - 0) Bit 15-0 : PDIR 15- PDIR0, PIO Direction Register. Set 1: Configure the PIO pin as an input. Set 0: Configure the PIO pin as an output or as normal pin function. Offset : 70h Reset Value : 0000h PIO Mode 0 Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PMODE (15 - 0) Bit 15-0: PMODE15-PMODE0, PIO Mode Bit. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 79 RDC ® R8820LV RISC DSP Controller 19. PSRAM Control Unit The PSRAM interface is provided by the R8820LV and the refresh control unit automatically generates refresh bus cycles. The refresh control unit uses the internal microprocessor clock as a operating source clock. if the power-saved mode is enabled, the refresh control unit must be programmed to reflect the new clock rate. Software programs the registers (E0, E2, E4) to control the refresh control unit operation. Offset : E0h Reset Value : 0000h Memory Partition Register 15 14 13 12 11 10 9 M6 - M0 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 Bit 15-9: M6-M0, Refresh Base. M6-M0 map to A19-A13 of the 20-bit memory refresh address. Bit 8-0 : Reserved. Offset : E2h Reset Value : Clock Prescaler Register 15 14 13 12 11 10 9 0 0 0 0 0 0 0 8 7 6 5 4 3 2 1 0 RC8 - RC0 Bit 15-9 : Reserved Bit 8-0: RC8-RC0, Refresh Counter Reload Value. Offset : E4h Reset Value : 0000h Enable RCU Register 15 14 13 12 11 10 9 E 0 0 0 0 0 0 8 7 6 5 4 3 2 1 0 T8 - T0 Bit 15: E, Enable RCU. Set 1: Enable the refresh counter unit Set 0 : Disable the refresh counter unit. Bit 14-9 : Reserved Bit 8-0: T8-T0, Refresh Count. Read only bits and these bits present value of the down counter which triggers refresh requests. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 80 RDC ® R8820LV RISC DSP Controller 20. INSTUCTION SET OPCODES AND CLOCK CYCLES Function DATA TRANSFER INSTRUCTIONS MOV = Move register to register/memory register/memory to register immediate to register/memory immediate to register memory to accumulator accumulator to memory register/memory to segment register segment register to register/memory PUSH = Push memory register segment register immediate POP = Pop memory register segment register PUSHA = Push all POPA = Pop all XCHG = Exchange register/memory register with accumulator XTAL = Translate byte to AL IN = Input from fixed port variable port OUT = Output from fixed port variable port LEA = Load EA to register LDS = Load pointer to DS LES = Load pointer to ES ENTER = Build stack frame L=0 L=1 L>1 LEAVE = Tear down stack frame LAHF = Load AH with flags SAHF = Store AH into flags PUSHF = Push flags POPF = Pop flags ARITHMETIC INSTRUCTIONS ADD = Add reg/memory with register to either immediate to register/memory immediate to accumulator Format 1000100w 1000101w 1100011w mod reg r/m mod reg r/m mod 000 r/m 1011w reg data 1010000w 1010001w 10001110 10001100 addr-low addr-low mod 0 reg r/m mod 0 reg r/m 11111111 01010 reg 000reg110 011010s0 mod 110 r/m data data data if w=1 addr-high addr-high Clocks data if w=1 1/1 1/6 1/1 1 6 1 3/8 2/2 8 3 2 1 data if s=0 10001111 mod 000 r/m 01011 reg 01) 000 reg 111 (reg¡ Ú 01100000 01100001 8 6 8 36 44 1000011w 10010 reg 11010111 mod reg r/m 3/8 3 10 1110010w 1110110w port 12 12 1110010w 1110110w port 10001101 11000101 11000100 11001000 mod reg r/m mod reg r/m mod reg r/m data-low 12 12 1 14 14 (mod¡ Ú 11) (mod¡ Ú 11) data-high L 7 11 11+10(L-1) 7 2 2 2 11 11001001 10011111 10011110 10011100 10011101 000000dw 100000sw 0000010w Notes mod reg r/m mod 000 r/m data data data if w=1 data if sw=01 1/7 1/8 1 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 81 RDC ® R8820LV RISC DSP Controller Function ADC = Add with carry reg/memory with register to either immediate to register/memory immediate to accumulator INC = Increment register/memory register SUB = Subtract reg/memory with register to either immediate from register/memory immediate from accumulator SBB = Subtract with borrow reg/memory with register to either immediate from register/memory immediate from accumulator DEC = Decrement register/memory register NEG = Change sign register/memory CMP = Compare register/memory with register register with register/memory immediate with register/memory immediate with accumulator Format Clocks 000100dw 100000sw 0001010w mod reg r/m mod 010 r/m data 1111111w 01000 reg mod 000 r/m 001010dw 100000sw 0001110w mod reg r/m mod 101 r/m data 000110dw 100000sw 0001110w mod reg r/m mod 011 r/m data 1111111w 01001 reg mod 001 r/m 1/8 1 1111011w mod reg r/m 1/8 0011101w 0011100w 100000sw 0011110w mod reg r/m mod reg r/m mod 111 r/m data 1/7 1/7 1/7 1 MUL = multiply (unsigned) register-byte register-word memory-byte memory-word IMUL = Integer multiply (signed) register-byte register-word memory-byte memory-word register/memory multiply immediate (signed) 1111011w mod 100 r/m 011010s1 mod reg r/m DIV = Divide (unsigned) register-byte register-word memory-byte memory-word IDIV = Integer divide (signed) register-byte register-word memory-byte memory-word 1111011W mod 110 r/m AAS = ASCII adjust for subtraction DAS = Decimal adjust for subtraction AAA = ASCII adjust for addition DAA = Decimal adjust for addition AAD = ASCII adjust for divide AAM = ASCII adjust for multiply CBW = Corrvert byte to word CWD = Convert word to double-word 00111111 00101111 00110111 00100111 11010101 11010100 10011000 10011001 data data if w=1 data if sw=01 Notes 1/7 1/8 1 1/8 1 data data if w=1 data if sw=01 1/7 1/8 1 data if w=1 data data if w=1 1/7 1/8 1 data if sw=01 13 21 18 26 1111011w mod 101 r/m data data if s=0 16 24 21 29 23/28 18 26 23 31 1111011w mod 111 r/m 18 26 23 31 00001010 00001010 3 2 3 2 14 15 2 2 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 82 RDC ® R8820LV RISC DSP Controller Function BIT MANIPULATION INSTRUCTUIONS NOT = Invert register/memory AND = And reg/memory and register to either immediate to register/memory immediate to accumulator OR = Or reg/memory and register to either immediate to register/memory immediate to accumulator XOR = Exclusive or reg/memory and register to either immediate to register/memory immediate to accumulator TEST = And function to flags , no result register/memory and register immediate data and register/memory immediate data and accumulator Sifts/Rotates register/memory by 1 register/memory by CL register/memory by Count STRING MANIPULATION INSTRUCTIONS MOVS = Move byte/word INS = Input byte/word from DX port OUTS = Output byte/word to DX port CMPS = Compare byte/word SCAS = Scan byte/word LODS = Load byte/word to AL/AX STOS = Store byte/word from AL/AX Format Clocks 1111011w mod 010 r/m 001000dw 1000000w 0010010w mod reg r/m mod 100 r/m data data data if w=1 data if w=1 1/7 1/8 1 000010dw 1000000w 0000110w mod reg r/m mod 001 r/m data data data if w=1 data if w=1 1/7 1/8 1 001100dw 1000000w 0011010w mod reg r/m mod 110 r/m data data data if w=1 data if w=1 1/7 1/8 1 1000010w 1111011w 1010100w mod reg r/m mod 000 r/m data data data if w=1 data if w=1 1/7 1/8 1 1101000w 1101001w 1100000w mod TTT r/m mod TTT r/m mod TTT r/m 1010010w 0110110w 0110111w 1010011w 101011w 1010110w 1010101w Notes 1/7 count 2/8 1+n / 7+n 1+n / 7+n 13 13 13 18 13 13 7 Repeated by count in CX: MOVS = Move byte/word INS = Input byte/word from DX port OUTS = Output byte/word to DX port CMPS = Compare byte/word SCAS = Scan byte/word LODS = Load byte/word to AL/AX STOS = Store byte/word from AL/AX PROGRAM TRANSFER INSTRUCTIONS Conditional Transfers ¡ Xjump if: JE/JZ = equal/zero JL/JNGE = less/not greater or equal JLE/JNG = less or equal/not greater JC/JB/JNAE = carry/below/not above or equal JBE/JNA = below or equal/not above JP/JPE = parity/parity even JO = overflow JS = sign JNE/JNZ = not equal/not zero JNL/JGE = not less/greater or equal JNLE/JG = not less or equal/greater JNC/JNB/JAE = not carry/not below /above or equal JNBE/JA = not below or equal/above JNP/JPO = not parity/parity odd JNO = not overflow JNS = not sign 11110010 11110010 11110010 1111011z 1111001z 11110010 11110100 1010010w 0110110w 0110111w 1010011w 1010111w 0101001w 0101001w 4+9n 5+9n 5+9n 4+18n 4+13n 3+9n 4+3n 01110100 01111100 01111110 01110010 01110110 01111010 01110000 01111000 01110101 01111101 01111111 01110011 disp disp disp disp disp disp disp disp disp disp disp disp 1/9 1/9 1/9 1/9 1/9 1/9 1/9 1/9 1/9 1/9 1/9 1/9 01110111 01111011 01110001 01111001 disp disp disp disp 1/9 1/9 1/9 1/9 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 83 RDC ® R8820LV RISC DSP Controller Function Format Clocks Notes Unconditional Transfers CALL = Call procedure direct within segment reg/memory indirect within segment indirect intersegment direct intersegment 11101000 11111111 11111111 10011010 disp-low mod 010 r/m mod 011 r/m segment offset selector disp-high data-low data-high data-low data-high (mod¡ Ú 11) 11 12/17 25 18 RET = Retum from procedure within segment within segment adding immed to SP intersegment instersegment adding immed to SP JMP = Unconditional jump short/long direct within segment reg/memory indirect within segment indirect intersegment direct intersegment 11101011 11101001 11111111 11111111 11101010 disp-low disp-low mod 100 r/m mod 101 r/m segment offset selector Iteration Control LOOP = Loop CX times LOOPZ/LOOPE = Loop while zero/equal LOOPNZ/LOOPNE = Loop while not zero/equal JCXZ = Jump if CX = zero 11100010 11100001 11100000 11100011 disp disp disp disp 7/16 7/16 7/16 7/15 Interrupt INT = Interrupt Type specified Type 3 INTO = Interrupt on overflow BOUND = Detect value out of range IRET = Interrupt return 11001101 11001100 11001110 01100010 11001111 type 41 41 43/4 21-60 31 PROCESSOR CONTROL INSTRUCTIONS CLC = clear carry CMC = Complement carry STC = Set carry CLD = Clear direction STD = Set direction CLI = Clear interrupt STI = Set interrupt HLT = Halt WAIT = Wait LOCK = Bus lock prefix ESC = Math coprocessor escape NOP = No operation 11111000 11110101 11111001 11111100 11111101 11111010 11111011 11110100 10011011 11110000 11011MMM mod PPP r/m 10010000 2 2 2 2 2 5 5 1 1 1 1 1 SEGMENT OVERRIDE PREFIX CS SS DS ES 00101110 00110110 00111110 00100110 2 2 2 2 11000011 11000010 11001011 1001010 mod reg r/m disp-high (mod ?11) 16 16 23 23 9/9 9 11/16 18 11 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 84 RDC ® R8820LV RISC DSP Controller 20.1 R8820LV Execution Timings The above instruction timing represent the minimum execution time in clock cycles for each instruction. The timings given are based on the following assumptions: 1. The opcode, along with and data or displacement required for execution, has been prefetched and resides in the instruction queue at the time is needed. 2. No wait states or bus HOLDs occur. 3. All word -data is located on even-address boundaries. 4. One RISC micro operation(uOP) maps one cycle(according the pipeline stages described below) , except the following case: Pipeline Stages for single micro operation(one cycle): Fetch à Decode à op_r à ALU à WB (For ALU function uOP) Fetch à Decode à EA à Access à WB (For Memory function uOP) 4.1 Memory read uOP need 6 cycles for bus. Pipeline stages for Memory read uOP(6 cycles): Fetch à Decode àEA à Access à Idle à T0 à T1 à T2 à T3 à WB Bus Cycle 4.2 Memory push uOP need 1 cycle if it has no previous Memory push uOP, and 5 cycles if it has previous Memory push or Memory Write uOP. Pipeline stages for Memory push uOP after Memory push uOP (another 5 cycles): Fetch à Decode à EA à Access à Idle à (2nd uOP) Fetch à Decode àEA à Access à T0 à T1 à T2 à T3 à WB Accessà Accessà Accessà Access (1st Memory push uOP) àIdle à T0 à T1 à T2 à T3 à WB pipeline stall 4.3 MUL uOP and DIV of ALU function uOP for 8 bits operation need both 8 cycles, for 16 bits operation need both 16 cycles. 4.4 All jumps, calls, ret and loopXX instructions required to fetch the next instruction for the destination address(Unconditional Fetch uOP) will need 9 cycles. Pipeline stages for unconditional fetch: Fetch à Decode à EA à Accessà (next uOP) Fetchà Decodeà EA Idle à T0 à T1 à T2 à T3 àFetch (Fetch uOP) à Accessà Accessà Accessà Accessà AccessàIdle à T0à T1à T2àT3àWB will be flushed àFetchà Decodeàfollowing stages...(New uOP) These 9 cycles caused branch penalty Note: op_r: operand read stage, EA: Calculate Effective Address stage, Idle: Bus Idle stage, T0..T3: Bus T0..T3 stage, Access: Access data from cache memory stage. Rev:1.0 RDC Semiconductor Co. Subject to change without notice 85 RDC ® R8820LV RISC DSP Controller 21. DC Characteristics Absolute Maximum Rating Symbol Rating Vterm Terminal Voltage with Respect To GND Ta Operating Temperature Pt Power Dissipation Recommended DC Operating Conditions Symbol Parameter Vcc Supply Voltage GND Ground Commercial -0.5 to Vcc+0.5 V V Unit 0 to +70 Centigrade 1.5 W Note Min. Typ. Max. Unit 3.0 3.3 3.6 V 0 0 0 V --- Vcc+0.5 V Vih Input High Voltage(1) 2.0 Vih1 Input High Voltage(RES) 2.5 Vcc+0.5 V Vih2 Input High Voltage (X1) 2.5 Vcc+0.5 V Input Low voltage -0.5 0.8 V Vil 0 Note 1: RST ,X1 pins not included DC Electrical Characteristics Symbol Parameter Ili Input Leakage Current (for 32 Pio Pins) Ili Input Leakage Current (Others) Ilo Output Leakage Current VOL Output Low Voltage VOH Output High Voltagr Note1:Vmax=3.6V Test Condition Min Unit 300 uA 80 uA 300 uA _____ 0.4 V 2.4 ____ V Vcc=Vmax Vin=GND to Vcc Vcc=Vmax Vin=GND to Vcc Vcc=Vmax Vin=GND to Vcc Iol=2mA, Vcc=Min. Ioh=-2.4mA, Vcc=Min. Max Vmin=3.0V Rev:1.0 RDC Semiconductor Co. Subject to change without notice 86 RDC ® R8820LV RISC DSP Controller DC Electrical Characteristics Symbol Parameter Icc Max Operating Current Fmax Max operation clock frequency Fmax Max operation clock frequency Test condition Vcc=3.6V, 33MHz Min --- Max 85 Unit mA Note 5 33 Mhz Vcc+-5% 5 25 Mhz Vcc+-10% Rev:1.0 RDC Semiconductor Co. Subject to change without notice 87 RDC ® R8820LV RISC DSP Controller 22.AC Characteristics T1 T2 T3 CLKOUTA T4 TW 2 A19:A0 ADDRESS 1 4 3 S6 6 5 AD15:AD0 8 ADDRESS DATA 10 9 ALE 11 7 12 13 15 14 RD BHE 16 17 UCS,LCS 18 19 PCS x,MCSX 20 21 DEN 22 23 DTR 24 25 S2:S0 STATUS 26 27 UZI READ CYCLE Rev:1.0 RDC Semiconductor Co. Subject to change without notice 88 RDC ® R8820LV RISC DSP Controller No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Description CLKOUTA high to A Address Valid A address valid to RD low S6 active delay S6 inactive delay AD address Valid Delay Address Hold Data in setup Data in Hold ALE active delay ALE inactive delay Address Valid after ALE inactive ALE width RD active delay RD Pulse Width RD inactive delay CLKOUTA HIGH to LCS UCS valid UCS,LCS inactive delay PCS , MCS active delay MIN 0 1.5T-12 0 0 0 0 10 3 0 0 1/2T-10 T-10 0 2T-15 0 0 0 0 MAX 15 20 20 20 20 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 19 20 20 20 12 20 20 15 PCS , MCS inactive delay 0 20 ns 20 DEN active delay 0 20 ns 21 22 23 24 25 26 DEN inactive delay DTR active delay DTR inactive delay Status active delay Status inactive delay UZI active delay 0 0 0 0 0 0 20 20 20 20 20 20 ns ns ns ns ns ns 27 UZI inactive delay 0 20 ns 1. T means a clock period time 2. All timing parameters are measured at 1.5V with 50 PF loading on CLKOUTA . All output test conditions are with CL=50 pF Rev:1.0 RDC Semiconductor Co. Subject to change without notice 89 RDC ® R8820LV RISC DSP Controller T1 T2 T3 CLKOUTA T4 TW 2 A19:A0 ADDRESS 1 4 3 S6 5 6 AD15:AD0 ADDRESS 7 DATA 9 8 ALE 10 11 13 12 WR 14 15 WHB,WLB 16 17 BHE 18 19 UCS,LCS 20 21 PCSx,MCSX 22 23 DEN 24 25 DTR 26 27 S2:S0 STATUS 28 29 UZI WRITE CYCLE Rev:1.0 RDC Semiconductor Co. Subject to change without notice 90 RDC ® R8820LV RISC DSP Controller No. 1 2 3 4 5 6 7 8 9 10 11 Description CLKOUTA high to A Address Valid A address valid to WR low S6 active delay S6 inactive delay AD address Valid Delay Address Hold ALE active delay ALE width ALE inactive delay Address valid after ALE inactive WR active delay MIN 0 1.5T-12 0 0 0 MAX 15 0 20 T-10 0 20 1/2T-10 0 15 Unit ns ns ns ns ns ns ns ns ns ns ns 12 WR pulse width 2T-15 ns 13 WR inactive delay 0 15 ns 14 WHB , WLB active delay 0 20 ns 15 16 17 18 WHB , WLB inactive delay BHE active delay BHE inactive delay CLKOUTA high to UCS , LCS valid 0 0 0 0 20 20 20 20 ns ns ns ns 19 UCS , LCS inactive delay 0 20 ns 20 PCS , MCS active delay 0 20 ns 21 PCS , MCS inactive delay 0 20 ns 22 DEN active delay 0 20 ns 23 24 25 26 27 28 DEN inactive delay DTR active delay DTR inactive delay Status active delay Status inactive delay UZI active delay 0 0 0 0 0 0 20 20 20 20 20 20 ns ns ns ns ns ns 29 UZI inactive delay 0 20 ns 20 20 15 Rev:1.0 RDC Semiconductor Co. Subject to change without notice 91 RDC ® R8820LV RISC DSP Controller T1 T2 T3 T4 T1 T2 T3 T4 T1 CLKOUTA A19:A0 d00C0 AD15:AD0 c0000 0 20000 2211 0 0 2211 101fc * 1fc * ALE RD WR WLB WHB UCS DEN DT/R S2:S0 7 5 7 6 7 6 S6 1 DRQ0 DMA (1) * The source-synchronized transfer is not followed immediately by another DMA transfer No. Description 1 DRQ is confirmed time MIN 0 MAX 10 Unit ns Rev:1.0 RDC Semiconductor Co. Subject to change without notice 92 RDC ® R8820LV RISC DSP Controller T1 T2 T3 T4 T1 T2 T3 T4 T1 T2 T3 T4 T1 T2 T3 T4 T1 CLKOUTA A19:A0 AD15:AD0 c0000 0 20000 2211 0 * C0002 2211 2 20002 4433 2 * 4433 101fc 1fc ALE RD WR WLB WHB UCS DEN DT/R S2:S0 5 7 6 7 5 7 6 7 6 S6 1 DRQ0 DMA (2) * The source-synchronized transfer is followed immediately by another DMA transfer No. 1 Description DRQ is confirmed time MIN 0 MAX 3 Unit ns Rev:1.0 RDC Semiconductor Co. Subject to change without notice 93 RDC ® R8820LV RISC DSP Controller T1 T2 T3 Tw Tw Tw T4 Ti Ti Ti Ti Ti Ti Ti Ti Ti Ti Ti Ti T1 CLKOUTA A19:A0 AD15:AD0 ffff4 ffff6 fff6 f0 fff* zZZZZ 0 fff6 f0000 0 b8 ALE RD WR WLB UCS DEN DT/R S2:S0 4 7 4 7 z 1 7 4 3 HOLD 2 4 HLDA HOLD/HLDA Timing No. 1 2 3 4 Description HOLD setup time HLDA Valid Delay HOLD hold time HLDA Valid Delay MIN 0 0 0 0 MAX 10 20 3 20 Unit ns ns ns ns Rev:1.0 RDC Semiconductor Co. Subject to change without notice 94 RDC ® R8820LV RISC DSP Controller T1 T2 T3 Tw Tw Tw Tw Tw Tw T4 T1 CLKOUTA ALE 2 1 ARDY SRDY LCS ARDY Timing No. 1 2 Description ARDY Resolution Transition setup time ARDY active hold time MIN 0 0 MAX 10 10 Unit ns ns Rev:1.0 RDC Semiconductor Co. Subject to change without notice 95 RDC ® R8820LV RISC DSP Controller T1 T2 T3 Tw Tw Tw Tw Tw T4 T1 CLKOUTA ALE ARDY 1 2 SRDY LCS SRDY Timing No. 1 2 Description SRDY transition setup time SRDY transition hold time MIN 0 0 MAX 10 3 Unit ns ns Rev:1.0 RDC Semiconductor Co. Subject to change without notice 96 RDC ® R8820LV RISC DSP Controller 23. PACKAGE INFORMATION (PQFP) D 23.20 0.25 D1 20.00 0.10 0.25 E 17.20 0.10 E1 14.00 "A" "A" 0.65 BSC 0.089 0.25 MIN A1 SEATING PLANE c 0.22/0.38 WITH PLATING c BASE METAL 0.13/0.23 b c1 0.13/0.17 b1 0.22/0.30/0.33 3.40 MAX A2 2.75 0.12 L1 0~7 L 7 TYP 15 TYP DETAIL A 1.60 REF 0.88 0.15 0.25 DETAIL A Rev:1.0 RDC Semiconductor Co. Subject to change without notice 97 RDC ® R8820LV RISC DSP Controller (LQFP) 16.00 0.10 14.00 0.10 25 51 50 0.127(TYP) 26 0.10 75 16.00 1 0.10 76 14.00 100 0.50(TYP) 0.22 0.05 "A" 0 ~ 7 0.10 0.60 0.2S(TYP) GAUGE PLANE 1.40 0.05 0.076(MAX) 0.05 1.60(MAX) Sealing Plane 0.15 1.00(REF) UNIT:mm Rev:1.0 RDC Semiconductor Co. Subject to change without notice 98