RFHIC RWP05020-10

Wideband Power Amplifier
Product Features
RWP05020-10
Application
0B
1B
GaN on SiC Broadband High Power Amplifier
HF/VHF/UHF
20 to 1000MHz Operation Bandwidth
Small Signal Gain 38dB min
20W Typical. P3dB
Package : DP-75
Description
2B
The power amplifier module is designed for Broadcasting, Telecommunication, Medical and Other markets.
Operating frequency range is from 20MHz to 1000MHz.
Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband
performance is already applied.
Improved thermal handling by patented technology.
Typical Specifications
No
Item
VCC = +28V; T = 25℃; ZS = ZL = 50Ω
Conditions
Min
1
Bandwidth
20
2
Small Signal Gain
38
3
Gain Variation vs Temperature
4
Gain Variation vs Frequency
5
P3dB
6
OIP3 @ Po = +33dBm
(1MHz Tone spacing, CW 2-Tone)
-20°C to 60°C
Typ
40
-2
±1
20MHz to 400MHz
42
44
400 MHz to 1000MHz
41
43
20MHz to 400 MHz
50
53
400 MHz to 700 MHz
47
50
700 MHz to 1000 MHz
45
47
Max
Unit
1000
MHz
42
dB
+2
dB
±1.5
dBpp
dBm
dBm
7
Input Return Loss
-15
-10
dB
8
Output Return Loss
-10
-7
dB
9
2nd Harmonic suppression
-35
-30
dBc
10
Supply Voltage
27.5
28
30
V
11
Quiescent Current consumption
1.7
1.9
2.1
A
12
Current Consumption @ P3dB
2.3
3
A
13
On/Off Switching Time
3
5
uS
14
CW 1-tone
@Po = +30dBm, Freq 500MHz
Vcc(=Vds)
CW 1-tone
On : TTL "Low"
Off : TTL "High"(300mA@Disable)
Shut Down or Switch On/Off
On : TTL “Low”(Enable)
TTL Voltage
Off : TTL “High”
0
2.5
0.5
5
V
5.5
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1
Wideband Power Amplifier
RWP05020-10
Environmental Characteristics
No
Item
Min
Typ
Max
Unit
1
Operating Temperature
-20
+60
°C
2
Storage Temperature
-40
+105
°C
3
Vibration
MIL-STD-810G Method 514.6 ANNEX C
Absolute Maximum Ratings
No
Item
Rating
Unit
1
Operating Flange Temperature
+85
°C
2
Input RF Power
+10
dBm
3
Supply Voltage
+30
V
4
Load Mismatch Value
3 : 1 @ all load phase
* Input Signal Condition : CW 1-Tone
Ordering Information
No
Part Number
Package
1
RWP05020-10
Pallet
2
RWP05020-1H
Module assembled with RWP05020-10
* RWP05020-1H is a SMA connectorized housing version of RWP05020-10. Electrical parameters are all same as RWP05020-10.
For more information, please contact RFHIC
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1
Wideband Power Amplifier
RWP05020-10
RWP05020-10 Typical Performance @ 25℃
4B
Frequency
P1dB
P3dB
Current@P1dB
Current@P3dB
2nd Harm
OIP3 (30dBm/Tone)
(MHz)
(dBm)
(dBm)
(A)
(A)
@30dBm(dBc)
(dBm)
20
42.4
44.3
1.9
2.2
-43.4
54.4
100
42.5
44.5
2.0
2.2
-42.5
54.9
200
43.3
44.8
2.1
2.3
-39.9
55.1
300
44.2
45.4
2.1
2.3
-35.8
54.6
400
44.6
45.6
2.1
2.3
-33.4
53.6
500
43.7
45.3
2.0
2.3
-34.9
52.2
600
43.9
44.9
2.0
2.2
-47.1
51.4
700
43.4
44.5
1.9
2.1
-42.5
49.4
800
42.8
44.2
1.8
1.9
-47.3
48.3
900
42.0
43.7
1.8
2.0
-55.1
47.5
1000
41.7
44.1
2.0
2.3
-54.1
47.1
2nd Harmonics
48.0
-10.0
47.0
-15.0
46.0
-20.0
45.0
-25.0
44.0
-30.0
MAG(dBc)
-35.0
z
z
z
10
00
M
H
90
0M
H
z
80
0M
H
z
70
0M
H
z
z
60
0M
H
20
M
H
90
0M
H
z
z
80
0M
H
70
0M
H
60
0M
H
z
z
z
50
0M
H
z
z
40
0M
H
30
0M
H
z
z
20
0M
H
10
0M
H
20
M
H
z
10
00
M
H
z
Frequency (MHz)
Frequency (MHz)
IM3 @ 20MHz
IM3 @ 500MHz
-20
-20
-25
-25
-30
-30
-35
-35
MAG(dBc)
MAG(dBc)
50
0M
H
-60.0
z
38.0
40
0M
H
-55.0
30
0M
H
-50.0
39.0
z
-45.0
40.0
z
-40.0
41.0
z
42.0
20
0M
H
43.0
10
0M
H
MAG (dBm)
P3dB
-40
-45
-40
-45
-50
-50
-55
-55
-60
-60
-65
-65
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Output Power (dBm)
Output Power (dBm)
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1
35
Wideband Power Amplifier
RWP05020-10
IM3 @ 1000MHz
Gain
45
-10
-15
-20
40
-25
MAG(dB)
MAG(dBc)
-30
-35
-40
35
-45
-50
30
-55
-60
-65
25
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
10
35
250
500
750
Input Return Loss
1250
1500
1750
2000
1500
1750
2000
Output Return Loss
0
0
-5
-5
-10
-10
MAG(dB)
MAG(dB)
1000
FREQ(MHz)
Output Power (dBm)
-15
-15
-20
-20
-25
-25
-30
-30
10
250
500
750
1000
1250
1500
1750
2000
10
250
500
FREQ(MHz)
750
1000
1250
FREQ(MHz)
Precautions
3B
1. This product is designed to be used for broadband amplification.
Heat generation is higher when there is no RF signal in the
device. Therefore, the worst case scenario is when there is
RF IN
RF OUT
no RF signal, and the amplifier is “on” with current draw.
Temp Monitor
Vcc(+28V)
The temperature must be calculated properly.
Shut Down
(+5V)
Switch ON/OFF
Case temperature must maintain below 85°C.
Right side drawing notes how to use a temperature monitoring
+Vcc
function to protect against overheating.
+
2. Thermal Grease or Metal Thermal Interface Materials are
-
Ref Voltage
recommended for heat dissipation. An example would be spreading
thermal grease on the bottom of the device.
Comparator Block (with hysteresis gap)
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1
Wideband Power Amplifier
RWP05020-10
Package Dimensions (Type: DP-75)
(Unit : mm/[inch], Tolerance : ±0.2/[.008])
How to connect the amplifier to a target PCB
Method-І (with Pin)
Method-ΙІ (without Pin) - If you cut out the pin
Pin Description
Pin No
Port Name
Function
1
RF IN
RF Input
2
Vcc (+28V)
DC Supply
3
Shut Down (+5V)
Shut Down @ TTL High, Enable @ TTL Low
4
Switch ON/OFF
Disable @ TTL High (Switch Status : Off)
5
Temp Monitor
0.85V @ 25℃, Scale : 10mV/℃ (Accuracy : ±3℃)
6
RF OUT
RF Output
* Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket)
U
U
U
U
* Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1
Wideband Power Amplifier
RWP05020-10
Note :
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not
assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or
incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for
inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not
intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells
such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders,
employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of
whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
▪ Tel : 82-31-250-5078
▪ All specifications may change without notice.
▪ www.rfhic.com/contact
▪ Version 2.1