Wideband Power Amplifier Product Features RWP15020-G1 Application UHF/Military GaN on SiC Broadband High Power Amplifier 1000 to 2000MHz Operation Bandwidth Small Signal Gain 27dB min 20W Typical. P3dB Description Package : DP-75 The power amplifier module is designed for Broadcasting, Telecommunication, Medical, Military and Other markets. Operating frequency range is from 1000MHz to 2000MHz. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology. Typical Specifications No Item 1 Bandwidth 2 Small Signal Gain 3 Gain Variation vs Temperature 4 Gain Variation vs Frequency 5 P3dB 6 VCC = +28V; T = 25℃; ZS = ZL = 50Ω Conditions Min Typ 1000 27 -20°C to 60°C 29 -2 ±1 1000MHz to 1200MHz 41 43 1200MHz to 2000MHz 42 44 OIP3 @ Po = +33dBm 1000MHz to 1600MHz 48 50 (1MHz Tone spacing, CW 2-Tone) 1600MHz to 2000MHz 46 48 Max Unit 2000 MHz 31 dB +2 dB ±2 dBpp dBm dBm 7 Input Return Loss -10 -6 dB 8 Output Return Loss -10 -5 dB 9 2nd Harmonic suppression -35 -28 dBc 10 Supply Voltage 28 30 V 11 Quiescent Current consumption 2.2 2.5 A 12 Current Consumption @ P3dB 3.6 A 13 On/Off Switching Time 5 uS 14 CW 1-tone @Po = +30dBm, Freq 1000MHz Vcc(=Vds) 27.5 CW 1-tone On : TTL "Low" 3 Off : TTL "High"(300mA@Disable) Shut Down or Switch On/Off On : TTL “Low”(Enable) TTL Voltage Off : TTL “High” 0 2.5 0.5 5 V 5.5 ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP15020-G1 Environmental Characteristics No Item Min Typ Max Unit 1 Operating Temperature -20 +60 °C 2 Storage Temperature -40 +105 °C 3 Vibration MIL-STD-810G Method 514.6 ANNEX C Absolute Maximum Ratings No Item Rating Unit 1 Operating Flange Temperature +85 °C 2 Input RF Power +20 dBm 3 Supply Voltage +30 V 4 Load Mismatch Value 3 : 1 @ all load phase * Input Signal Condition : CW 1-Tone Ordering Information No Part Number Package 1 RWP15020-G1 Pallet 2 RWP15020-GH Module assembled with RWP15020-G1 * RWP15020-GH is a SMA connectorized housing version of RWP15020-G1. Electrical parameters are all same as RWP15020-G1. For more information, please contact RFHIC. ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP15020-G1 RWP15020-G1 Typical Performance @ 25℃ Frequency P1dB P3dB Current@P1dB Current@P3dB 2nd Harm OIP3 (30dBm/Tone) (MHz) (dBm) (dBm) (A) (A) @30dBm(dBc) (dBm) 1000 39.4 42.5 2.3 2.9 -34.7 49.5 1100 39.8 42.9 2.4 3.1 -43.5 49.8 1200 40.6 43.8 2.1 3.3 -49.4 50.4 1300 41.5 44.5 2.5 3.3 -47.7 50.8 1400 42.1 44.5 2.5 3.3 -43.3 51.0 1500 42.3 45.2 2.5 3.2 -41.8 51.1 1600 43.0 45.4 2.4 3.0 -43.8 51.0 1700 43.2 45.4 2.3 2.7 -46.1 50.3 1800 42.6 44.8 2.1 2.5 -49.6 49.5 1900 42.4 44.3 2.0 2.3 -52.7 48.5 2000 42.0 43.9 2.0 2.3 -61.3 47.6 P3dB 2nd Harmonics OIP3 Power Gain @ Pin=18dBm ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP15020-G1 Precautions 1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is no RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly. Case temperature must maintain below 85°C. 2. Thermal Grease or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device. Package Dimensions (Type: DP-75) (Unit : mm/[inch], Tolerance : ±0.2/[.008]) 70 [2.756] 70 [2.756] 60 [2.362] 60 [2.362] 20 [.787] 38 [1.496] 50.8 [2] 45 [1.772] 20 [.787] 1.5 [.059] 15.6 [.616] 50.8 [2] 7.3 [.288] 'A' 7.3 [.286] 6.2 [.245] 6.9 [.273] C 38 [1.496] 6.9 [.273] 1 [.039] 17.1 [.673] 3.8 [.15] 5 [.197] 4 [.156] 2.5 [.098] 4.5 [.177] 4.1 [.161] 2 [.079] 1.5 [.059] How to connect the amplifier to a target PCB Method-І (with Pin) Method-ΙІ (without Pin) - If you cut out the pin ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP15020-G1 Pin Description Pin No Port Name Function 1 RF IN RF Input 2 Vcc (+28V) DC Supply 3 Shut Down (+5V) Shut Down @ TTL High, Enable @ TTL Low 4 Switch ON/OFF Disable @ TTL High (Switch Status : Off) 5 GND Ground 6 RF OUT RF Output * Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt Note : RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1