Wideband Power Amplifier Product Features RWP06040-10 Application GaN on SiC Broadband High Power Amplifier UHF Television 450 to 880MHz Operation Bandwidth Small Signal Gain 38dB min 40W Typical. P3dB Package : DP-75 Description The RWP06040-10 is designed for Wideband Power Amplifier application frequencies from 450 to 880MHz. This module uses GaN HEMT technology which performs high breakdown voltage, high linearity, wide bandwidth and high efficiency. Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband performance is already applied. Improved thermal handling by patented technology. Typical Specifications No Item VCC = +28V; T = 25℃; ZS = ZL = 50Ω Conditions Min 1 Bandwidth 450 2 Small Signal Gain 38 3 Gain Variation vs Temperature 4 Gain Variation vs Frequency 5 P3dB -20°C to 60°C Typ 40 -2.0 ±1 Max Unit 880 MHz 42 dB +2.0 dB ±2 dBpp 450MHz to 880MHz 44 45 dBm 450MHz to 880MHz 49 51 dBm OIP3 @ Po = +33dBm 6 (1MHz Tone spacing, CW 2Tone) 7 Input Return Loss -12 -10 dB 8 Output Return Loss -11 -7 dB 9 ACLR@Pout=28dBm W-CDMA,64PCH,4FA Spectrum Analyzer Setting : RBW=30KHz, VBW=10KHz 10 Supply voltage 11 Quiescent Current consumption 12 On/Off Switch Time 13 △=5MHz 45 48 △=10MHz 48 51 △=5MHz 44 45 △=10MHz 47 48 27.5 28 30 V 2.5 2.7 A 3.0 5.0 uS 450MHz dBc 880MHz Vcc(=Vds) On: TTL "Low" Off: TTL "High"(300mA@Disable) Shut Down or Switch On/Off On : TTL “Low”(Enable) TTL Voltage Off : TTL “High” 0 0.5 V 2.5 5 5.5 ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Environmental Characteristics No Item Min Typ Max Unit 1 Operating Temperature -20 +60 °C 2 Storage Temperature -40 +105 °C 3 Vibration MIL-STD-810G Method 514.6 ANNEX C Absolute Maximum Ratings No Item Rating Unit 1 Operating Flange Temperature +85 °C 2 Input RF Power +12 dBm 3 Supply Voltage +30 V 4 Load Mismatch Value 3 : 1 @ all load phase * Input Signal Condition : CW 1-Tone Ordering Information No Part Number Package 1 RWP06040-10 Pallet 2 RWP06040-1H Module assembled with RWP06040-10 * RWP06040-1H is a SMA connectorized housing version of RWP06040-10. Electrical parameters are all same as RWP06040-10. For more information, please contact RFHIC. ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 RWP06040-10 Typical Performance @ 25℃ Frequency P1dB P3dB Current Current OIP3 W-CDMA 64CH 4FA @ 28dBm @P1dB @P3dB (30dBm/Tone) -5MHZ +5MHZ -10MHZ +10MHZ (MHz) (dBm) (dBm) (A) (A) (dBm) (dBc) (dBc) (dBc) (dBc) 450MHz 44.4 45.6 2.3 2.4 51.6 -48.0 -48.1 -50.8 -51.0 550MHz 42.5 44.9 2.4 3.1 50.8 -46.3 -46.4 -49.1 -49.3 650MHz 42.5 44.9 2.4 3.2 50.2 -45.4 -45.7 -48.1 -48.6 750MHz 43.0 45.4 2.5 3.0 50.5 -45.7 -46.1 -48.4 -48.9 880MHz 43.1 45.4 2.5 3.0 50.3 -45.5 -46.0 -48.2 -48.8 Gain Input Return Loss 45 0 40 -5 35 MAG(dB) M A G (dB ) -10 30 25 -15 -20 20 -25 15 -30 10 10 440 850 1300 10 1700 440 P3 1300 1700 OIP3 48.0 59.0 47.0 57.0 46.0 55.0 OIP3 (dBm) P3 (dBm) 850 FREQ(MHz) FREQ(MHz) 45.0 44.0 43.0 42.0 53.0 51.0 49.0 41.0 47.0 40.0 450MHz 650MHz Freq (MHz) 880MHz 45.0 450MHz 650MHz Freq (MHz) ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 880MHz Wideband Power Amplifier RWP06040-10 W-CDMA, 64PCH, 4FA ACLR, PAPR 11.3dB ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Precautions 1. This product is designed to be used for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst case scenario is when there is RF IN RF OUT no RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly. Temp Monitor Vcc(+28V) Shut Down (+5V) Switch ON/OFF Case temperature must maintain below 85°C. Right side drawing notes how to use a temperature monitoring +Vcc function to protect against overheating. + 2. Thermal Grease or Metal Thermal Interface Materials are - Ref Voltage recommended for heat dissipation. An example would be spreading thermal grease on the bottom of the device. Comparator Block (with hysteresis gap) ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Package Dimensions (Type: DP-75) (Unit : mm/[inch], Tolerance : ±0.2/[.008]) How to connect the amplifier to a target PCB Method-І (with Pin) Method-ΙІ (without Pin) - If you cut out the pin Pin Description Pin No Port Name Function 1 RF IN RF Input 2 Vcc (+28V) DC Supply 3 Shut Down (+5V) Shut Down @ TTL High, Enable @ TTL Low 4 Switch ON/OFF Disable @ TTL High (Switch Status : Off) 5 Temp Monitor 0.85V @ 25℃, Scale : 10mV/℃ (Accuracy : ±3℃) 6 RF OUT RF Output * Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket) * Recommended Screw Torque : 8.0kgf.cm±1 using SEMS M3 10mm Bolt ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1 Wideband Power Amplifier RWP06040-10 Note : RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5078 ▪ All specifications may change without notice. ▪ www.rfhic.com/contact ▪ Version 1.1