RSG CX-1SO.T.-03

CX-1-03 CRYSTAL
8 MHz to 160 MHz
Miniature AT-Cut Quartz Crystal
™
Fundamental Mode: 8 MHz - 70 MHz
Third Overtone Mode: 48 MHz - 160 MHz
DESCRIPTION
The CX-1 quartz crystal is a high quality miniature AT cut
quality resonator. The CX-1 is hermetically sealed in a
rugged, miniature ceramic package, one-fourth the size of an
eight-pin mini-DIP. The CX-1 crystal is manufactured using
the STATEK-developed photolithographic process, and was
designed utilizing the experience acquired by producing
millions of crystals for industrial, commercial, military and
medical applications.
FEATURES
actual size
side view
PACKAGE DIMENSIONS
Low-profile hermetically-sealed package
F
E
Excellent aging characteristics
Fundamental or 3rd overtone mode
High shock resistance
D
A
Full military testing available
Designed and manufactured in the USA
B
PACKAGE HANDLING
The CX crystal is hermetically sealed in a ceramic package.
Normal handling and soldering precautions for small, low
thermal mass parts are adequate when installing or testing
CX crystals. CX crystals may be wave soldered, with proper
precaution taken to avoid desoldering the leads. A slow
machine rate or too high a pre-heat temperature or solder
bath temperature can damage the crystals. Lead to
package solder interface temperature should not
exceed 175oC, glass lid to package seal rim
temperature should not exceed 210oC. If the seal rim
reaches temperatures above the maximum specified, the
package may lose its hermeticity resulting in degradation of
crystal performance. Mishandling of CX crystals can cause
cracking of the glass lid and loss of hermeticity.
C
TYP.
MAX.
DIM
INCHES
mm
INCHES
mm
A
.315
8.00
.330
8.38
B
.140
3.56
.155
3.94
C
.070
1.78
.080
2.03
D
.300
7.62
.310
7.87
E
.020
0.51
.040
1.02
F
.150
3.81
.160
4.06
Leads 0.013” x 0.018” (0.33 x 0.46 mm) typical.
EQUIVALENT CIRCUIT
C0
1
L1
C1
R1
2
R1 Motional Resistance L1 Motional Inductance
C1 Motional Capacitance C0 Shunt Capacitance
10127 - Rev D
RSG Electronic Components GmbH, Sprendlinger Landstr. 115, 63069 Offenbach, Germany, Tel. +49 69 - 984047-0, Fax: +49 69 - 9840-77, www.rsg-electronic.de
SPECIFICATIONS
CIRCUIT DESIGN
Specifications are typical at 25oC unless otherwise noted.
Specifications are subject to change without notice.
10 MHz 32MHz 155.52 MHz
A conventional CMOS Pierce Oscillator is shown below.
The crystal oscillates at a frequency fO above the crystal’s
series-resonant frequency fs. The crystal is effectively
inductive and, in combination with RA, Cd and Cg in the
feedback loop, provides approximately 180O phase shift
necessary to obtain oscillation. Typical component values
for a Pierce Oscillator using a 16 MHz crystal with a
74HC04 hex inverter are shown below:
Motional Resistance R1 (⍀) 50
20
50
Motional Capacitance C1 (fF) 5.5
7.8
0.5
Quality Factor Q (k)
36
41
2.6
3.2
80
Shunt Capacitance Co (pF) 2.2
Calibration Tolerance*
A
+
_
0.01% ( 100ppm)
B
+
_
0.1%
Typical Application as Pierce Oscillator
Using 74HC04 CMOS Hex Inverter at 5 VDC
+
_
Load Capacitance
C +_ 1.0%
20 pF (Unless specified by customer)
Drive Level
500 ␮W MAX.
Frequency-Temperature
Stability**
CONVENTIONAL CMOS
PIERCE OSCILLATOR CIRCUIT
-10OC to +70OC from
+
_
10ppm
-40OC to +85OC from
+
_
20ppm
-55OC to +125OC from
+
_
30ppm
Aging, first year
5ppm MAX.
Shock, survival***
3,000g, .3 msec., 1/2 sine
Vibration, survival
20g rms, 10-2,000 Hz random
Operating Temperature
Range
-10OC to +70OC Commercial
-40OC to +85OC Industrial
-55OC to +125OC Military
Storage Temperature
-55OC to +125OC
Rf
BUFFER
CG
Note: The characteristics of the frequency temperature stability follow that of AT
cut thickness-shear mode*
* Tighter tolerances available as low as +_ 5 ppm
** Does not include calibration tolerance
*** Higher shock version available, refer to data sheet model CX-1HG (10108)
OSC
Freq (fO)
RA
AMPLIFIER
CS
Contact factory for
design guidelines
CD
CX-1
STANDARD FREQUENCIES
10.0
11.0592
12.0
14.318
16.0
PACKAGING
CX-1-03 - Tray Pack (Standard)
MHz
MHz
MHz
MHz
MHz
19.6608
20.0
24.0
24.576
30.0
MHz
MHz
MHz
MHz
MHz
32.0
MHz
35.2512 MHz
36.0
MHz
40.0
MHz
HOW TO ORDER CX-1-03 CRYSTALS
CX-1
“S” if special or
custom design.
Blank if Std.
-03
O.T.=3RD O.T. Mode C=Ceramic Lid
Blank=Fundamental Blank=Glass Lid
Mode
*Other calibration fill in ppm.
32 MHz
Frequency
(
25ppm
Calibration
Tolerance*
@25OC
(A)
(B)
(C)
/
25ppm
/
50ppm
/
I
)
Frequency
Total Frequency Temp. Range:
Stability over Tolerance
C = Commercial
Temp. Range
I = Industrial
M = Military
S = Specify
10127 - Rev D
RSG Electronic Components GmbH, Sprendlinger Landstr. 115, 63069 Offenbach, Germany, Tel. +49 69 - 984047-0, Fax: +49 69 - 9840-77, www.rsg-electronic.de