CXO3M OSCILLATOR 300 kHz to 170 MHz Low-Profile Miniature Surface-Mount 3.3 V Crystal Oscillator ™ DESCRIPTION Statek’s surface-mount 3.3 V CXO3M oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. GM M 4.19 FEATURES Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques actual size side view 3.3 V operation CMOS and TTL compatible Low power consumption Optional Output Enable/Disable with Tri-State DIMENSIONS Low EMI emission High shock resistance D Full military testing available 2 Hermetically sealed ceramic package A TOP 3 BOTTOM APPLICATIONS 1 4 Military & Aerospace D Smart Munitions B Cockpit Systems E C Navigation Industrial, Computer & Communications TYPICAL Industrial Controls Instrumentation MAXIMUM DIM inches mm inches mm A 0.256 6.50 0.263 6.68 B Microprocessor Clocks Medical Infusion Pumps SUGGESTED LAND PATTERN 0.197 5.00 0.204 5.18 0.051 C (SM1) C (SM3/SM5) 0.055 1.30 1.40 0.055 0.063 1.40 1.60 D 0.055 1.40 0.065 1.65 E 0.060 1.52 0.070 1.78 0.070 (1.78) 0.067 (1.70) PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 3. Output 0.136 (3.45) 4. VDD GRID PLACEMENT COURTYARD 10126 Rev E ■ ■ 90 ■ Änderungen vorbehalten / subject to change without notice ■ 01 TEM C ERT I F I C AT N IO ■ YS IS O Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de S 0.137 (3.48) inches (mm) ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS O Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC for 20 seconds Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 3.3 V Calibration Tolerance2 + _ Frequency Stability Over Temperature3 + _ + _ 10% ENABLE/DISABLE OPTIONS (E/T/N) 100 ppm Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. 50 ppm for Commercial 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 2 mA 24 MHz 4 mA 30 MHz 6 mA 40 MHz 8 mA 50 MHz 10 mA + _ Supply Current (Typical) Output Load (CMOS)4 15 pF Start-up Time Rise/Fall Time 5 ms MAX 6 ns MAX Duty Cycle 40% MIN, 60% MAX Aging, first year COMPARISON OF ENABLE/DISABLE OPTIONS E AND T 10 ppm MAX Shock, survival 3,000 g, 0.3 ms, 1/2 sine Vibration, survival6 20 g, 10-2,000 Hz swept sine 5 E T When enabled (PIN 1 is high*) Operating Temp Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 5.0 V, see CXOM data sheet (10116). For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory about CXO3MHG. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Output Freq. output Freq. output Oscillator Oscillates Oscillates Current consumption Normal Normal Output High Z state High Z state Oscillator Stops Oscillates Current consumption Very low Lower than normal When disabled (PIN 1 is low) When re-enabled (PIN 1 changes from low to high) Output recovery Delayed Immediate PACKAGING OPTIONS * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. CXO3M- Tray Pack - 16 mm tape, 7˝ or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) HOW TO ORDER CXO3M SURFACE MOUNT CRYSTAL OSCILLATORS S T “S” if special or custom design; otherwise blank. SM3 Enable/Disable Option E, T, or N Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 32.0M , Frequency K = kHz M = MHz 100 / 100 / / Frequency Stability over Temp.Range (in ppm) Calibration Tolerance @ 250C (in ppm) Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 Total Frequency Tolerance (in ppm) Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10126 Rev E ■ ■ ■ YS 90 Änderungen vorbehalten / subject to change without notice I IS O ■ / 01 TEM C ERT I F I C AT N IO Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ I S CXO3M