SF10L60U VOLTAGE 600V Elektronische Bauelemente 10 AMP Low Loss Super Fast Rectifiers RoHS Compliant Product ITO-220A A suffix of "-C" specifies halogen-free 10 0.5 0.2 0.1 3.2 4.5 0.2 0.3 2.8 * Plastic Material Used Carries Underwriters Laboratory Flammability Classification 94V-O 0.3 15 1 3 2 0.2 13Min 0.2 1.3 3.7 * High Surge Capacity * Glass Passivated Chip Junctions o * 150 C Operating Junction Temperature * Low Power Loss, High Effciency * High-Switching Speed 25 Nanosecond Recovery Time * Low Forward Voltage, High Current Capability * Low Stored Charge Majority Carrier Conduction 2.7 0.2 Features 5.08 0.7 0.2 0.2 Pin 1 Pin 3 0.2 0.5 2.6 0.2 Pin 2 Dimensions in millimeters Maximum Ratings and Electrical Characteristics Characteristic Symbol Peak Repetitive Reverse Voltage VRRM Working Peak Reverse Voltage VRWM SF10L60U Unit 600 V VR 480 V Averge Rectifier Forward Current IF(AV) 10 A Non-Repetitive Peak Surge Current (Surge Applied At Rate Load Conditions Halfware,Single Phase,60Hz) IFSM 120 DC Blocking Voltage Tj, Tstg -65~+150 Max. Instantaneous Forward Voltage (IF=10Amp,TC=25oC) VF 2.5 Max. Instantaneous Reverse Current o (Rated DC Voltage, TC=25 C) o (Rated DC Voltage, TC=100 C) IR Operating Junction and Storage Temperature Range Reverse Recovery Time (IF=0.5A,IR=1A,IRR=0.25A) Typical Junction Capacitance (Reverse Voltage of 4V & f=1MHz) Thermal Resistance http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A uA 500 25 CP 70 2.0 C V 10 TRR Rth(j to c) A o nS pF o C/W Any changing of specification will not be informed individual Page 1 of 2 SF10L60U VOLTAGE 600V Elektronische Bauelemente 10 AMP Low Loss Super Fast Rectifiers RATING AND CHARACTERISTIC CURVES FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr 10W NONINDUCTIVE ( ) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) 1W NONINDUCTIVE | | | | | | | | +0.5A (+) AVERAGE FORWARD CURRENT,(A) 50W NONINDUCTIVE 0 -0.25A (+) OSCILLISCOPE (NOTE 1) -1.0A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 1cm 2. Rise Time= 10ns max., Source Impedance= 50 ohms. 12 10 8 Single Phase 6 Half Wave 60Hz Resistive Or Inductive Load 4 2 0 SET TIME BASE FOR 0 25 50 75 100 125 150 175 CASE TEMPERATURE,( C) 50 / 10ns / cm FIG.3-TYPICAL FORWARD FIG.4-TYPICAL REVERSE CHARACTERISTICS CHARACTERISTICS 1000 10 REVERSE LEAKAGE CURRENT, ( A) INSTANTANEOUS FORWARD CURRENT,(A) 50 3.0 1.0 Tj=25 C Pulse Width 300us 1% Duty Cycle 0.1 .01 0 0.5 1.0 1.5 2.0 2.5 3.0 100 Tc=100 C 10 Tc=25 C 1.0 0.1 3.5 20 40 60 80 100 120 140 FIG.6-TYPICAL JUNCTION CAPACITANCE FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 125 JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) 0 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FORWARD VOLTAGE,(V) 100 75 Tj=25 C 8.3ms Single Half Sine Wave 50 JEDEC method 25 150 125 100 75 50 25 0 0 1 5 10 NUMBER OF CYCLES AT 60Hz http://www.SeCoSGmbH.com 01-Jun-2002 Rev. A 50 100 .01 .05 .1 .5 1 5 10 50 100 REVERSE VOLTAGE,(V) Any changing of specification will not be informed individual Page 2 of 2